Desoldering Wick Technique: How to Remove Solder Cleanly

Desoldering wick braid roll, 10 ft, 0.1 inch width, copper

Desoldering Wick Technique: How to Remove Solder Cleanly

Desoldering wick technique uses a copper braid to pull molten solder off a joint by capillary action. The wick roll at $13.99 gives you 10 ft of 0.1 in no-clean braid for PCB rework and component removal. Heat the wick on the joint with light pressure, wait for the solder to absorb, then cut off the used section.

Desoldering wick braid roll, 10 ft, 0.1 inch width, copper
Desoldering wick braid, 10 ft roll with 0.1 in width for PCB rework.
63-37 rosin core solder wire spool, 0.8 mm, 100 g
63/37 solder wire, 0.8 mm diameter, melting at 183C for clean joints.

Quick facts

Fact Value
Wick length and width 10 ft roll, 0.1 in width, no-clean
Wick material Copper braid, spool diameter 1.8 in
Solder wire 63/37 tin lead, 0.8 mm, 100 g spool
Solder melt point 183C (361F), 1.8% rosin flux core
Flux paste RMA-223 rosin, no-clean, 10cc syringe
Flux needle 1 mm inner diameter, 30 mm needle tip

How does desoldering wick technique work?

The copper braid absorbs molten solder fast through capillary action once heated.

The 0.1 in braid works from the tip of the wick, per its listing.

Place the wick on the joint, heat it with light pressure, and wait for absorption.

How do you avoid lifting pads?

Use light pressure only, and let the heat and the braid do the work.

The solder melts at 183C, so heat the joint just past that point and no further.

Cut off the used section of wick before you move to the next joint.

When do you add flux paste?

Add flux paste when old solder resists flow or the joint looks dull and dry.

The RMA-223 paste comes in a 10cc syringe with a 1 mm needle tip for precise placement.

No-clean flux needs no residue cleanup after soldering in most cases, per its listing.

What solder wire suits rework after wicking?

The 63/37 wire is a eutectic tin lead alloy with a 1.8% rosin flux core.

Its 0.8 mm diameter suits RC wiring, ESCs, motors, and board work.

A lead warning applies: this is tin lead solder, not lead free solder.

What did we check against the listings?

We matched the 10 ft length and 0.1 in width to the wick listing.

We matched the 183C melt point and the 0.8 mm diameter to the solder listing.

We counted 4 images on the wick listing, 3 on the solder listing, and 5 on the flux listing.

How the options compare

Product Size Amount Key spec Price
Desoldering wick 0.1 in wide 10 ft roll Copper braid, no-clean $13.99
Solder wire 0.8 mm 100 g spool Melts at 183C $17.99
Flux paste 1 mm needle 10cc syringe RMA-223, no-clean $6.64

How do you use desoldering wick in 5 steps?

  1. Add a drop of flux paste to the joint when the solder looks old or dull.
  2. Place the wick on the solder joint with the braid tip on the solder.
  3. Heat the wick with the iron tip using light pressure only.
  4. Wait for the solder to absorb into the braid, then lift the iron and wick together.
  5. Cut off the used section of wick before you start the next joint.

Parts that fit this guide

Check stock before you order, because in-stock parts ship from New York in 1-2 business days. Prices in this guide are the live store prices verified on November 12, 2026.

Desoldering Wick Braid, 10ft, 0.1in Width, No-Clean, 1 Roll ($13.99)

Desoldering wick braid at $13.99. It is a 10 ft roll of 0.1 in no-clean copper braid for PCB rework and component removal.

63/37 Rosin Core Solder Wire, 0.8mm, 100g ($17.99)

63/37 rosin core solder wire at $17.99. It is 0.8 mm wire on a 100 g spool that melts at 183C for clean joints.

Rosin Flux Paste, No-Clean, RMA-223, 10cc Syringe with Plunger & Needle Tip ($6.64)

Rosin flux paste at $6.64. It is RMA-223 no-clean paste in a 10cc syringe with a plunger and needle tip.

Shop the full range in the Tools and Soldering category at Quality RC Parts. See also: Related guide.

Frequently asked questions

Can you reuse a section of wick?

No. Cut off the used section after the solder absorbs, per the listing instructions.

Does the flux paste need cleanup?

No-clean flux needs no residue cleanup after soldering in most cases, per its listing.

Is the solder wire lead free?

No. It is 63/37 tin lead solder with a lead warning, not lead free solder.

What width is the wick braid?

The wick measures 0.1 in wide on a 10 ft roll, with a 1.8 in spool diameter.

Sources

Last updated: November 15, 2026.

Related guides

Orders earn QRC Rewards points.

Shipped fast and securely from our secure facility in New York, providing fast, high quality USA shipping.