Identify RC Connector: XT60, JST, Bullet, and Balance Lead Checks
To identify RC connector types, measure the pin pitch first, count the pins, read the housing and latch, and check the wire gauge. Pitch separates JST families: 1.25mm, PH at 2.0mm, and XH at 2.54mm. Pin count separates balance leads by cell count. Housing shape separates XT60, EC3, and bare bullets. Measure the plug in hand before ordering a mate.
This guide is the identification method, not another chooser. The live catalog already has buying guides for XT60 connectors, silicone wire, and heat shrink; those are linked at the end. What follows is the procedure for the plug you already hold: how to measure it, how to name it, and how to check the wire and heat shrink that go with it. Prices were checked November 18, 2026. Shipped fast and securely from our secure facility in New York, providing fast, high quality USA shipping.
Identify RC connector types in four steps
Work in this order: pitch, pin count, housing, wire. Pitch first, because two white JST housings can look identical while their pins sit at different spacing, and a 2.0mm plug will never mate with a 2.54mm header. Pin count second, because balance leads are defined by cell count. Housing third, because the latch and keying decide whether a plug mates at all. Wire gauge last, because the wire tells you what current the lead was built for.
You need one tool for all four steps: a caliper. The Digital Caliper, 100mm / 150mm ($8.55 for 100mm, $9.78 for 150mm) reads to 0.01mm accuracy. Measure pin centers, not housing edges: close the jaws on the center of the first pin and the center of the last pin, then divide by the number of pins minus one. That is the method the JST guides below describe, and it removes housing width from the measurement. The caliper battery (AG13 cell) is not included.
Step 1: measure pitch and name the JST family
JST is a family of small white connectors, and pitch is what separates them. The CZT JST guide lists PH at 2.0mm pitch and XH at 2.5mm pitch, while the live listings state XH at 2.54mm. Treat those as the same part described two ways: guides round, listings state the exact 2.54mm spacing. Measure your connector and match to the nearest value in the table. A reading of 2.5mm on a caliper with 0.1mm resolution is consistent with a 2.54mm XH part.
| Family | Pitch | How to confirm | Live example |
|---|---|---|---|
| JST 1.25mm | 1.25mm | Smallest common pitch; 2-pin pigtails with 15cm 28AWG leads | 2-pin pigtails, 5 pairs $4.99 |
| JST-PH | 2.0mm | Mid-size white housing with latch; 2-pin pigtails with 20cm 26AWG leads | 2-pin pigtails, 5 pairs $6.46 |
| JST-XH | 2.54mm | Largest of the three; balance leads and board headers; 2-pin pigtails with 20cm 26AWG leads | 2-pin pigtails, 5 pairs $6.62 |
The JST 1.25mm / PH 2.0mm / XH 2.54mm 2-Pin Pigtail Connectors listing sells all three pitches as 2-pin male and female sets with wire leads, in 5-pair or 10-pair packs, rated 24V. It is the fastest way to confirm a pitch guess: order the pitch you measured and check the mate. For building custom leads, the JST-XH 2.54mm Connector Kit, 500pcs ($12.72) holds housings, crimp terminals, and through-hole pin headers in 2, 3, 4, 5, and 6-pin sizes, with nylon housings rated from -25C to +85C. This is a parts kit for building leads, not pre-made cables.
One labeling warning: the JST Wiring Connector Kit ($21.95) lists its contents as a 230-piece kit plus JST plug pairs and JST-XH balance wire extensions, but one contents line reads “230Pcs 2.54mm JST-PH”. PH is 2.0mm pitch and 2.54mm is XH, so that line mixes two families. The same listing also lists plug pairs at 1.25mm, PH 2.0mm, and XH 2.54mm separately. Before ordering mates for anything in that kit, measure the pitch of the parts in hand with a caliper and match the measured pitch, not the mixed label.
Step 2: count pins and name the balance lead
LiPo balance leads follow one rule: pins equal cells plus one. A 2S pack has a 3-pin balance plug, a 4S pack has 5 pins, and a 6S pack has 7 pins. Count the pins on the plug in hand, subtract one, and you have the cell count. Balance leads are almost always JST-XH at 2.54mm pitch, which the extension lead listing confirms.
| Battery | Balance pins | Extension lead (20cm, 22AWG, 5 pieces) |
|---|---|---|
| 1S | 2 | $7.37 |
| 2S | 3 | $7.77 |
| 3S | 4 | $8.09 |
| 4S | 5 | $8.77 |
| 5S | 6 | $9.97 |
| 6S | 7 | $10.65 |
The JST-XH 1S-6S Balance Extension Leads, 20cm, 5 Pieces extend a short balance lead so it reaches the charger without straining the battery lead. Match the lead to the battery: a 3S battery needs the 3S lead. For older packs with a non-XH balance tap, the JST to JST-XH Balance Adapter Set, 2S-6S ($5.99) adapts JST male balance taps to JST-XH chargers on 20AWG wire, covering 2S through 6S in one set. Balance leads take the most handling abuse in the hobby, so the 2S JST-XH Balance Connector Saver, 5-Pack ($4.50) and 4S JST-XH Balance Connector Saver, 5-Pack ($4.50) add a bigger grip so you pull the saver, not the wires.
Step 3: read the housing and latch for power connectors
Power connectors identify by housing, not pitch. XT60 has a yellow keyed nylon housing that prevents reverse polarity. EC3 has a blue housing over gold bullets and is also polarized. Bare bullets have no housing at all: a male pin and a female barrel, sized by diameter. MT60 packs three cores into one housing for three-wire motor and battery runs.
The XT60H Male and Female Connector Set, 10 Pairs ($13.99) is the standard high-current battery connector: gold-plated copper contacts, rated DC 500V, 30A rated current and 60A max, suited to 12AWG silicone wire, with a high-temperature nylon housing rated from -20C to +120C and 1000 mating cycles. The H variant adds a sheath housing and a half-open end for easier soldering. For a pre-wired option, the XT60 Extension Cable, 14AWG ($6.31 for one male pigtail, $6.33 for one female, $10.99 for five, $13.99 for ten) is an XT60 pigtail on 14AWG silicone wire in 10, 15, or 20cm lengths, rated 30A with 60A instantaneous.
Bullet connectors identify by barrel diameter, measured with the caliper across the male pin. The Gold Plated 3.5mm Bullet Connector Pair, 10 Sets ($6.99) is the standard for motor-to-ESC leads on most sport setups. The Gold Plated 4mm Bullet Connector Pair, 10 Sets ($8.99) handles the current that 3.5mm bullets struggle with on bigger setups. The 8.0mm Gold-Plated Bullet Connectors, 2 Pairs ($3.99) are sized for 8AWG wire, with solder-cup ends and cross holes. Solder the leads in and cover the joint with heat shrink: bare bullets have no housing to protect them. The EC3 Connector Male/Female Pair, 5 Sets ($5.99) solders the same way, then the plastic housings slide on to make a polarized connection that cannot plug in backwards. The MT60 3-Core Battery Connector (from $4.99 for a single connector) is an Amass three-core connector rated 36V, sold as male, female, or pairs, with or without 12AWG silicone wire leads in 10, 20, or 30cm lengths. Choose the gender, pair, and lead option on the listing that matches the harness in hand.
| What you see | What to measure | Likely connector |
|---|---|---|
| Yellow keyed housing, two solder cups | Cup size and wire gauge | XT60 or XT60H |
| Blue housing over gold bullets | Housing size, bullet diameter | EC3 |
| Bare gold pin and barrel, no housing | Barrel diameter with calipers | Bullet: 3.5mm, 4mm, or 8.0mm |
| Three cores in one housing | Housing size, wire count | MT60 |
| Small white housing, latch, 2 to 6 pins | Pin pitch, pin count | JST family: 1.25mm, PH, or XH |
Step 4: check the wire gauge and the heat shrink
Wire gauge is printed on the listing, not on the wire, so identification means measuring outside diameter and matching it to the listing table. The Silicone RC Wire, Red/Black, 10AWG to 26AWG listing gives strand counts and outside diameters for each gauge, rated from -65 to +200C, in 2-meter lengths (4 meters for 26AWG). Measure the outside diameter with the caliper and match it to the table. Insulation thickness varies by brand, so diameter alone is a guide, not proof; confirm by checking the gauge the connector and the ESC manual call for.
| Gauge | Strands x 0.08mm | Outside diameter | Price (2m, red/black) |
|---|---|---|---|
| 10AWG | 1050 | 5.5mm | $17.99 |
| 12AWG | 680 | 4.5mm | $11.99 |
| 14AWG | 400 | 3.5mm | $8.99 |
| 16AWG | 252 | 3.0mm | $6.99 |
| 18AWG | 150 | 2.3mm | $5.99 |
| 20AWG | 100 | 1.80mm | $6.44 |
| 22AWG | 60 | 1.70mm | $6.25 |
| 24AWG | Not stated | Not stated | $4.99 |
| 26AWG | Not stated | Not stated | $6.38 (4m) |
Longer rolls cover full builds: 12AWG Flexible Silicone Wire, 20ft ($19.99, 10ft red and 10ft black), Flexible 14AWG Silicone Wire, 20ft ($15.99), Flexible 16AWG Silicone Wire, 20ft ($14.99), and Flexible 22AWG Silicone Wire, 45ft ($11.99), all silicone-insulated and rated to 200C. Do not pick a gauge from a single ampacity number: published silicone-wire current ratings conflict across vendors, and insulation, bundling, and run length all change the safe current. Use the gauge the ESC, battery, and connector listings call for, and check the listing rating for the exact wire you buy. The PowerStream and Engineering ToolBox tables in the sources give AWG diameter and area references for the measurement step.
Heat shrink sizing follows the joint, not the wire alone. The tube must slide over the soldered joint before shrinking and grip the wire after. The Heat Shrink Tubing Assortment, 4 Sizes ($15.95) covers 3mm, 4.5mm, 7mm, and 10mm in five packs of 20 pieces (10mm in red and black). The Heat Shrink Tubing Assortment (127/1600 Pieces) ($5.87 for 127 pieces, $25.99 for 1600 pieces with a box) is 2:1 polyolefin, flame retardant, rated from -55 to 125C, with a minimum shrink temperature of 84C and full shrink at 120C. A 2:1 ratio means the tube shrinks to half its diameter, so pick a size that fits over the joint with room to spare and still grips after shrinking. Shrink it with the Mini Heat Gun for Heat Shrink ($20.99), and strip the wire first with the Automatic Wire Stripper AWG 10-24 ($37.99), which covers the full range in the wire table above.
Identification checklist before you order
- Measure pin pitch center to center and divide by pins minus one. Name the JST family from the pitch.
- Count the pins. For balance leads, pins minus one equals cell count.
- Read the housing: color, keying, latch, and whether bullets sit inside a housing or bare.
- Measure bullet barrel diameter and wire outside diameter with the caliper.
- Check the wire gauge the ESC, battery, and connector listings call for. Do not guess from diameter alone.
- Pick heat shrink that fits over the finished joint and shrinks to grip the wire.
- Confirm the mate: order the gender, pin count, and pitch that match the plug in hand, not the one that looks close.
Limits of visual identification
Some connectors look alike and do not mate. JST-SH at 1.0mm pitch exists in the wider JST family and is smaller than the 1.25mm parts in this guide; if your pitch reading falls below 1.25mm, stop and measure again before ordering, because no listing in this guide covers that pitch. XT60 and XT90 share a shape at different sizes, so measure the housing and check the wire gauge rather than trusting color alone. Counterfeit and mislabeled kits exist, as the mixed JST-PH label warning above shows, so the caliper reading always wins over the label. If a plug will not mate with light pressure, do not force it: forced JST housings crack, and a cracked latch fails in flight or on the track.
Browse the full range in Connectors and Wiring and Heat Shrink and Tape. Related buying guides: Best Connectors and Wiring for RC, Best XT60 Connectors, Best XT60 and EC2 Connectors for RC, EC2 and EC3 Connector Family, JST-XH Balance Extension Leads for LiPo Charging, Best Silicone Wire for RC, Best Heat Shrink Tubing and Tape for RC, and Best Heat Shrink and Wire for FPV.
Frequently asked questions
How do I tell a JST-PH connector from a JST-XH connector?
Measure the pin pitch. PH is 2.0mm and XH is 2.54mm. Measure from the center of the first pin to the center of the last pin and divide by the number of pins minus one. The housings look alike, so pitch is the only reliable separator. Do not trust a kit label alone: one listing mixes a 2.54mm label with the PH name.
How do I measure connector pitch with calipers?
Close the caliper jaws on the center of the first pin and the center of the last pin, read the distance, and divide by pins minus one. Do not measure the outside edges of the housing; housing width includes wall thickness and gives a wrong pitch. A 0.01mm caliper gives a clean reading on 1.25mm, 2.0mm, and 2.54mm pitches.
How many pins does a 4S LiPo balance lead have, and why?
Five pins. Balance leads carry one wire per cell junction plus one ground, so pins equal cells plus one: 2S has 3 pins, 4S has 5, 6S has 7. Count the pins on the plug in hand and subtract one to get the cell count, then match the extension lead or adapter to that cell count.
What size bullet connector fits my motor and ESC wires?
Measure the barrel diameter of the bullet in hand with a caliper. The common sizes in this guide are 3.5mm for most sport motor-to-ESC leads, 4mm for bigger setups, and 8.0mm for 8AWG power runs. Match the diameter exactly: a 3.5mm male will not stay in a 4mm female, and a 4mm male will not fit a 3.5mm female.
What wire gauge do I need for a battery lead, and how do I check it?
Use the gauge the battery, ESC, and connector listings call for. XT60H suits 12AWG per its listing, and the XT60 pigtails here use 14AWG. Check the wire you hold by measuring outside diameter against the listing table, but confirm against the equipment ratings, because published ampacity numbers conflict across vendors and bundling and length change the safe current.
What size heat shrink fits over an XT60 solder joint?
Pick a tube that slides over the finished solder cup and the wire insulation with room to spare, then shrinks to grip. With 2:1 tubing, a 7mm or 10mm tube covers most XT60 joints on 12AWG to 14AWG wire. The 4-size assortment covers 3mm through 10mm, so one kit handles servo leads through battery joints.
