Measure 3D Printer Bearings, Bushings, Belts, and Nozzles Before You Order

Measure 3D Printer Bearings, Bushings, Belts, and Nozzles Before You Order

To measure 3D printer bearings, read three numbers with a caliper: bore, outside diameter, and width. A 608 bearing measures 8mm bore, 22mm outside diameter, and 7mm wide. Bushings, shaft supports, belts, and nozzles follow the same rule: measure the part in hand, read the size code, and match it exactly before ordering. Guessing a size costs a failed print and a return.

This guide is the measurement-first check for printer wear parts. It does not repeat the filament comparison or the bearing buying guides already live on this site; those are linked at the end. What follows is the caliper procedure for each part, the size codes that tell you what you hold, and the checks that prevent ordering the wrong replacement. Prices were checked November 18, 2026. Shipped fast and securely from our secure facility in New York, providing fast, high quality USA shipping.

Measure 3D printer bearings with three numbers

Every ball bearing is defined by bore (inside diameter), outside diameter, and width. Measure the bore across the inner ring, the outside diameter across the outer ring, and the width across the bearing standing on edge. A caliper is required: eyeballing a 1mm difference between bearing sizes is not reliable. The Digital Caliper, 100mm / 150mm ($8.55 for 100mm, $9.78 for 150mm) reads to 0.01mm accuracy with zero set anywhere, and the battery (AG13 cell) is not included.

The most common printer bearing is the 608. The 608ZZ / 608RS Ball Bearings, 8mm x 22mm x 7mm, 10-Pack ($7.99 for either type) are pre-lubricated chrome bearing steel. Choose 608ZZ with metal shields on both sides or 608RS with rubber seals on both sides for extra protection against dust and debris. The size code reads directly: 608 means 8mm bore, 22mm outside diameter, 7mm wide. If your measurement reads 8 x 22 x 7, a 608 is the replacement, and the only remaining choice is shields versus seals.

Flanged bearings add a lip that holds the bearing in its housing without a separate retaining clip. The F623ZZ / F624ZZ / F625ZZ Flanged Ball Bearings, 10-Pack are bearing steel (GCr15), single row, oil-grease lubricated, and the size code gives the three measurements directly:

Size code Bore x OD x width Price (10-pack)
F623ZZ 3 x 10 x 4mm $10.59
F623-2RS 3 x 10 x 4mm, rubber sealed $11.07
F624ZZ 4 x 13 x 5mm $10.59
F625ZZ 5 x 16 x 5mm $11.45
F626ZZ 6 x 19 x 6mm $12.90

Measure the flange too: the flange diameter decides whether the bearing seats in the housing. If the old bearing is pressed into a printed part or a pulley, remove it with the RC Bearing Puller and Installer Set, 2-14mm ($5.42), which has 9 stepped diameters (2, 3, 4, 5, 6, 8, 10, 12, 14mm) in aluminum alloy. Pressing a new bearing in by its inner ring damages it; the stepped tool pushes on the right ring.

Bushings and shaft supports: the number is the shaft size

Linear bushings ride on round shafts, and the number in the code is the shaft diameter. The LM8UU / LM6UU Linear Ball Bushings, 10-Pack are nickel-plated with double seals and 4 ball circuits each. The LM8UU measures 8mm inside diameter, 15mm outside diameter, and 24mm long, for 8mm shafts ($12.99). The LM6UU measures 6mm inside diameter, 12mm outside diameter, and 19mm long, for 6mm shafts ($11.99). Measure the shaft with the caliper first: an 8mm shaft needs LM8UU, a 6mm shaft needs LM6UU, and no bushing fits both. Also measure the housing bore the bushing presses into; it must match the bushing outside diameter.

Shaft supports hold the ends of those shafts and bolt to the frame. The SK8 / SK10 / SK12 / SK13 / SK16 Linear Shaft Supports, 4-Pack are aluminum with a clamping slot and bolt holes, and the number again names the shaft size. The mounting hole diameter is 5.5mm on all sizes, but the center height differs, and that height sets the axis position:

Support Shaft Size (mm) Center height Price (4-pack)
SK8 8mm 42 x 14 x 33 20mm $11.99
SK10 10mm 42 x 13 x 33 20mm $11.99
SK12 12mm 42.5 x 14 x 38 23mm $11.99
SK13 13mm 42 x 13.5 x 38 23mm $12.99
SK16 16mm 48 x 16 x 44 27mm $13.99

Measure the shaft, the mounting hole spacing on the frame, and the center height of the support you remove. A support with the right shaft size but the wrong center height shifts the whole axis. The listing notes these supports pair with LM8UU, LM10UU, LM12UU, and LM16UU bushings.

Belts and pulleys: pitch, width, and length

GT2 belts are the standard for printer linear motion, and the RepRap belt guide gives the identification method: GT2 means a 2mm tooth pitch, the belt pitch must match the pulley tooth profile, and at least 6 teeth should stay in contact with the pulley. Measure three things on the belt in hand: pitch (distance between tooth centers, 2mm for GT2), width (commonly 6mm, measured across the belt with the caliper), and length (measure the installed loop or count teeth and multiply by pitch). Measure the pulley too: count the teeth and check the bore against the motor shaft. A belt that fits the pitch but not the width will ride off the pulley, and a pulley with the wrong bore will not mount at all.

No GT2 belt or GT2 pulley listing could be verified live at the time of writing, so this section links no belt or pulley product. Check the 3D Printer Parts category for current stock before ordering, and measure pitch, width, length, tooth count, and bore first. Do not substitute a different tooth profile: an MXL pulley and a GT2 belt do not mesh, even if the bore matches. The same measurement discipline applies to the extruder drive gear below.

Nozzles: thread, bore, and length

Nozzle identification needs three measurements plus the hotend model: thread size, bore diameter, and overall length. The thread must match the heater block, the bore sets the extrusion width, and the length sets the nozzle tip position relative to the bed. No printer-nozzle listing could be verified live at the time of writing, so this section links no nozzle product. Check the 3D Printer Parts category for current stock, and confirm thread, bore, and length against your hotend documentation before ordering. A nozzle with the right bore and the wrong thread will not install, and a nozzle with the wrong length changes the first-layer gap. If the old nozzle is worn or clogged beyond cleaning, measure it before discarding it: the thread and length readings are the order specification.

Extruder gear, bed springs, and heat-set inserts

The extruder drive gear grips the filament and feeds it through the hotend. A worn gear slips and under-extrudes. The MK8 Extruder Drive Gear, Brass, 26T / 40T, 10-Pack ($9.06 for 26-tooth, $9.27 for 40-tooth) is brass with a 5mm bore, 11mm outer diameter, and 11mm length, and includes a 2.5mm hex wrench for the set screw. The listing states fit for CR-10, CR-10S, S4, S5, Ender 3, Ender 3 Pro, Anet A8 and A6, and most standard 3D printers. Count the teeth on the gear you remove and measure the bore: pick the tooth count that matches your existing gear, and confirm the 5mm bore fits your extruder motor shaft.

Bed leveling springs set the bed height and hold level while you fine-tune each corner. The 3D Printer Heated Bed Leveling Springs, 7mm OD x 20mm ($7.26 for 20 pieces, $8.87 for 30, $10.56 for 40, $11.76 for 50) measure 7mm outside diameter, 5mm inside diameter, and 20mm tall, with 1.2mm wire and 9 turns, in nickel-plated carbon steel. The listing states fit for Ender-3, CR-10, RepRap, Anet A8, and other printers with heated-bed leveling screws. Measure the old spring’s outside diameter and free height before ordering; a spring with the wrong outside diameter will not sit on the leveling screw.

Printed parts that need a reusable thread use heat-set inserts. The M3 Brass Heat-Set Threaded Inserts for 3D Prints, 5.7 x 4.6mm, 100-Pack ($13.99) are knurled brass, 5.7mm long with a 4.6mm outside diameter, rated for installation up to 300C, for PLA, PETG, ABS, and plastic parts. The check is the hole: measure the printed hole against the 4.6mm outside diameter. Too large a hole and the insert spins; too small and the plastic cracks or the insert seats crooked. Print a test hole and measure it with the caliper before committing a full part.

Filament checks: diameter, spool format, and storage

Filament measurement is a diameter check and a format check. Every filament listing in this section is 1.75mm diameter in a 1KG pack. Measure the filament diameter with the caliper at several points along the coil: the Anycubic PLA+ and PETG refills state a plus or minus 0.02mm tolerance, and the PLA+ spool states plus or minus 0.03mm. A reading that drifts well outside tolerance signals a bad coil or a measurement on a flattened section; measure again on a round section. This guide keeps filament selection short because two live posts already compare PLA, PLA+, and PETG in depth; they are linked at the end.

The format check matters more than the material choice for first-time buyers: refill coils ship without a spool, and full spools are ready to print. The Anycubic PLA Filament Refill, 1.75mm, 1KG ($19.99), Anycubic PLA+ Filament Refill, 1.75mm, 1KG ($24.99), and Anycubic PETG Filament Refill, 1.75mm, 1KG ($18.79) are refill coils only, with no spool included. Each needs an Anycubic reusable spool, a previous spool, or a printed spool, and each carries an intelligent identification chip for ACE Pro auto-identification. The PLA+ Filament, 1.75mm, 1KG ($24.99) is a full spool, ready to print, with nozzle settings of 200 to 230C and bed settings of 55 to 65C. The Polymaker HT-PLA Pro Filament, 1.75mm, 1KG ($29.99) is a full spool for parts that see heat, with nozzle settings of 220 to 230C and a build plate at 60 to 65C; the listing advises annealing printed parts at 100C for 30 minutes for the best heat resistance and drying the filament at 60C for 6 hours if it has absorbed moisture.

Bed adhesion is the last filament-adjacent check. The Creality 3D Printer Glue Stick, 21g ($9.99) and the 3D Print Bed Adhesion Glue Stick, 21g ($11.99) both list PLA, ABS, PETG, PC, PA, and TPU. Apply a thin layer on a cold, clean plate, print, and let the plate cool fully before removing the part. Browse filament in 3D Printer Filament and wear parts in Bearings and Linear Motion.

Measurement checklist before you order

  1. Bearings: measure bore, outside diameter, and width. Match all three numbers, then pick shields or seals.
  2. Flanged bearings: measure the flange diameter too, and confirm the housing seats the flange.
  3. Bushings: measure the shaft diameter and the housing bore. The code number is the shaft size.
  4. Shaft supports: measure the shaft, the mounting hole spacing, and the center height.
  5. Belts: measure pitch, width, and length. Pulleys: count teeth and measure the bore.
  6. Nozzles: measure thread, bore, and length, and confirm against hotend documentation.
  7. Extruder gears: count teeth and measure the bore. Bed springs: measure outside diameter and free height.
  8. Heat-set inserts: measure the printed hole against the insert outside diameter with a test print.
  9. Filament: measure diameter at several points, and confirm refill coil versus full spool before checkout.

Limits of measurement

A caliper reading is only as good as the part it measures. Worn bearings measure smaller than their size code because the rings and balls have worn; if a 608 reads 7.9mm bore instead of 8mm, trust the size code family, not the worn reading, and confirm against the housing bore. Printed holes shrink and vary with material and settings, so always test-print an insert hole. Belt length measured on a stretched belt overstates the replacement length; count teeth and multiply by pitch for the true length. Printer-model compatibility in this guide is stated only where the live listing states it: the extruder gear and bed springs name CR-10, Ender 3, and Anet models, and the PETG refill listing states compatibility with 99% of FDM 3D printers. No other model claims are made.

Related guides: PLA vs PLA+ vs PETG: Best Filament for Drone Parts, PLA and PETG Filament Comparison, Best 3D Printer Parts for RC, Filament Refill vs Spool, How to Store Filament, Which Bearing Should You Buy?, Rebuild 3D Printer Axis Bearings, and 3D Printer Maintenance.

Frequently asked questions

How do I measure a 608 bearing to order the right replacement?

Measure three numbers with a caliper: bore across the inner ring (8mm), outside diameter across the outer ring (22mm), and width (7mm). A 608 reads 8 x 22 x 7. Then choose shields (ZZ, metal) or seals (RS, rubber) based on dust exposure. If the old bearing is worn, its readings run slightly small; confirm against the housing bore.

What do the numbers in 608ZZ, LM8UU, and SK8 mean?

In 608, the code names a bearing size: 8mm bore, 22mm outside diameter, 7mm wide, with ZZ for metal shields or RS for rubber seals. In LM8UU, the 8 is the shaft diameter in millimeters: an 8mm shaft bushing, 15mm outside diameter, 24mm long. In SK8, the 8 is again the shaft diameter: a support for an 8mm shaft with a 20mm center height.

How do I measure a GT2 belt for length, width, and pitch?

Measure pitch as the distance between tooth centers: 2mm for GT2. Measure width across the belt with the caliper. For length, count the teeth and multiply by pitch, because a stretched belt measures long. Check the pulley too: count its teeth and measure its bore against the motor shaft. Belt pitch and pulley profile must match.

How do I tell which nozzle thread and bore my hotend takes?

Measure the old nozzle before discarding it: thread size, bore diameter, and overall length. Confirm all three against your hotend documentation, because the thread must match the heater block and the length sets the tip position. No nozzle listing could be verified live at the time of writing, so confirm current stock in the 3D Printer Parts category.

Is my filament 1.75mm, and is a refill coil or a full spool the right buy?

Measure the filament diameter with a caliper at several points; the listings in this guide are 1.75mm with plus or minus 0.02mm or 0.03mm tolerance. A refill coil ships without a spool and needs a reusable, previous, or printed spool. A full spool is ready to print. Buy the refill only if you already have a spool it fits.

How do I check a printed part for the right heat-set insert size?

Measure the printed hole against the insert outside diameter: 4.6mm for the M3 inserts in this guide. Print a test hole first and measure it with a caliper, because printed holes vary with material and settings. Too large and the insert spins; too small and the plastic cracks or the insert seats crooked.

Sources