Description
The DRV8825 is the step up from the A4988 when a build needs finer steps or more current. It is built around the Texas Instruments DRV8825 chip, on a StepStick-format carrier board that drops into the same socket as an A4988, with the same STEP and DIR control. If your board already runs an A4988, this module fits the same footprint and the same wiring.
What changes is the resolution and the current. The DRV8825 runs six step resolutions, from full step down to 1/32 step, where the A4988 stops at 1/16. The module is rated 1.5 A per coil; the chip maximum is 2.5 A per coil with proper heatsinking at 24 V and 25 C, against the A4988’s 2 A rating. The extra resolution makes motion smoother and quieter on 3D printers, CNC machines, and robot arms, and the extra current headroom covers bigger NEMA 17 steppers that run hot on an A4988.
Set the step size with the M0, M1, and M2 pins. All three low is full step; the table below lists every combination. One mapping difference matters if you are swapping from an A4988: the M0-M2 setting that gives 1/16 step on the A4988 gives 1/32 step on the DRV8825. Check the table before you power up, or the motor moves half as far per step as you expect.
Set the current with the onboard trimpot before running the motor. Start low, measure, and raise it only as far as the motor needs. The chip protects itself against overcurrent, short circuits, and overtemperature, and the nFAULT pin flags a fault to your controller. The module runs from 8.2 V to 45 V on the motor supply and 3 V to 5.25 V on the logic supply, so it works with Arduino, ESP32, and 3D printer boards. A heatsink is included for sustained current; above about 1.5 A per coil, give the module airflow or a heatsink, or the chip throttles on temperature.
This is a single module. If you are building a 3D printer or a CNC machine that needs four or five drivers, buy one per axis. The TMC2209 5-pack is the quieter option if silence matters more than current; the A4988 single is the cheaper option if 1/16 step and 2 A are enough. The full comparison is in our guide, Best Motor Drivers for Arduino.
Shipped fast and securely from our secure facility in New York, providing fast, high quality USA shipping. Quality RC Parts ships within the USA only.
Step resolution:
- M0 Low, M1 Low, M2 Low: Full step
- M0 High, M1 Low, M2 Low: Half step
- M0 Low, M1 High, M2 Low: 1/4 step
- M0 High, M1 High, M2 Low: 1/8 step
- M0 Low, M1 Low, M2 High: 1/16 step
- M0 High, M1 Low, M2 High: 1/32 step
- M0 Low, M1 High, M2 High: 1/32 step
- M0 High, M1 High, M2 High: 1/32 step
Specs:
- Driver chip: Texas Instruments DRV8825
- Motor supply (VMOT): 8.2 V to 45 V
- Logic supply: 3 V to 5.25 V
- Rated current: 1.5 A per coil
- Chip maximum current: 2.5 A per coil, with proper heatsinking, 24 V, 25 C
- RMS current: 1.75 A per coil (chip figure, with proper heatsinking)
- Microstepping: Full, 1/2, 1/4, 1/8, 1/16, 1/32
- Interface: STEP/DIR, MODE0-MODE2, nFAULT, sleep
- Decay modes: Mixed, slow, fast, configurable
- Reference output: Built-in 3.3 V reference
- Format: StepStick, drop-in A4988 replacement
- Heatsink: Included
- Current limit setting: Onboard trimpot








Reviews
There are no reviews yet.