Description
Two ESP32-CAM development boards, each with its own camera module. A matched pair for projects that need two wireless camera nodes, a spare board on the bench, or a side-by-side build and test setup. Each board runs a low-power dual-core 32-bit processor at up to 240 MHz with built-in WiFi and Bluetooth, and each ships with a camera module on a flex cable ready to plug into the board’s camera connector.
Specifications
| Processor | ESP32 low-power dual-core 32-bit CPU, up to 240 MHz, up to 600 DMIPS |
|---|---|
| Memory | 520 KB SRAM built in, external 8 MB PSRAM, SPIFlash default 32 Mbit |
| Wireless | WiFi 802.11 b/g/n + Bluetooth; STA, AP, and STA+AP working modes |
| Network setup | Smart Config / AirKiss one-click network configuration; WPA, WPA2, WPA2-Enterprise, WPS security |
| Interfaces | UART, SPI, I2C, PWM, ADC, DAC; 9 IO ports; serial port default 115200 bps |
| Camera | Camera module included with each board; board supports OV2640, OV3660, and OV7670 cameras |
| Storage | TF card supported, maximum 4 GB |
| Power | Working voltage 4.75-5.25 V; 180 mA at 5 V with flash off, 310 mA at 5 V with flash at maximum brightness |
| Sleep modes | Deep-sleep as low as 6 mA, modem-sleep as low as 20 mA, light-sleep as low as 6.7 mA (all at 5 V) |
| Firmware | Embedded LwIP and FreeRTOS; secondary development supported |
| Package | DIP package that plugs directly into a backplane for rapid production |
| Temperature | Working -20 C to 70 C; storage -40 C to 125 C, under 90% RH |
| Pinout | GPIO0, GPIO1, GPIO2, GPIO3, GPIO4, GPIO12, GPIO13, GPIO14, GPIO15, GPIO16, plus 5 V, 3.3 V, and GND pins; camera signals HS2 DATA0-DATA3, CLK, CMD, and CSIMCLK |
What does it work with?
The listing states compatibility with Arduino, and the board runs FreeRTOS with embedded LwIP for network projects. It supports OV2640, OV3660, and OV7670 camera modules, works in STA, AP, and STA+AP WiFi modes, and takes a TF card up to 4 GB for local storage. It connects over UART, SPI, I2C, PWM, ADC, and DAC to the sensors, displays, and peripherals in a typical IoT build.
What do I need?
A USB-to-serial (UART) adapter to program the board over its serial pins (default 115200 bps), a 5 V supply within the 4.75-5.25 V working range, and a TF card up to 4 GB if the project stores pictures or data locally. The TF card and the programming adapter are not in the package. The package holds the two boards and the two camera modules.
What is included: 2 x ESP32-CAM module, 2 x camera module.
What can I build with it?
Home smart devices, industrial wireless control, wireless monitoring, QR wireless identification, wireless positioning system signals, and picture wireless upload. The classic ESP32-CAM uses: a wireless camera that streams pictures over WiFi, a QR reader, a monitoring node that wakes, captures, and sleeps again on very little power, or any IoT device that needs eyes plus a radio.
Questions and answers
How many boards are in the pack? Two ESP32-CAM boards and two camera modules. This listing sells the whole 2-pack.
Which cameras does the board support? The board supports OV2640, OV3660, and OV7670 cameras. Each board ships with a camera module included.
Does it need a programmer? Yes, a USB-to-serial (UART) adapter is needed to program the board over its serial pins. The adapter is not included.
Can it store pictures locally? Yes, with a TF card up to 4 GB. The TF card is not included.
Prefer a single board? See the ESP32-CAM Development Board with OV2640 Camera Module, 4MB PSRAM.
This item is fulfilled in the USA. Shipped fast and securely from our secure facility in New York, providing fast, high quality USA shipping.
QRC Rewards: Earn points on every order, plus 100 points for an approved verified-purchase review, once per product. Learn how it works: How the Quality RC Parts Rewards Program Works.
Guides: How to Start with ESP32-CAM for WiFi Camera Projects, How to Choose ESP32-CAM Boards for WiFi Camera Projects, and How to Build a WiFi Security Camera with ESP32-CAM.







Reviews
There are no reviews yet.