RC Car Replacement Parts: Measure and Match Before You Order
RC car replacement parts fit by part number and measurement, not by scale alone. Identify the chassis and version, match the part number in the manual, then measure the interface: hex size, shock length, shaft length, gear fitment, and screw size. Scale tells you what standards to expect, and the numbers confirm whether the part bolts on and works.
Last updated: November 18, 2026. Prices in this guide were checked on that date.
Why RC car replacement parts need the part number first
Two 1/10 cars can share a scale, a screw size, and a wheel diameter yet share almost no suspension or drivetrain parts. The chassis family, kit generation, wheelbase, and drivetrain layout decide whether a replacement bolts on, clears every moving part, and keeps the geometry the car was designed around. The most useful number on a replacement part is usually the manufacturer part number for your exact chassis version, not the scale printed on the box.
The listings in this guide show both styles of fitment. Some state a part number and tell you to match it: the F/R Differential Gear for 1:10 Scale Cars (31007) at $18.99 states part number 31007 and says fitment is by part number, not by brand or model name, and the Rear Shock Tower for 1:10 Scale Cars (31004) at $11.99 states part number 31004 with the same warning. Others state model fitment in the listing: the Oil Shock Absorber Set for 1:10 Traxxas Slash, Stampede, Rustler, Hoss, Bandit, Blue at $40.99 lists Traxxas 1:10 Slash, Stampede, Rustler, Hoss, and Bandit in 2WD and 4×4, part number 5862, per the listing. In both cases, check the number or the model list against your manual before you order, and measure the old part as a second check.
How do you identify a drivetrain part?
Start with the assembly, not the single part. A differential works with a particular case, gear set, and driveshaft length. A driveshaft works with a particular wheelbase and joint cup. Identify the car, then the assembly, then the interface dimensions. The table below lists the drivetrain parts in this guide with the measurements and fitment lines their listings state.
| Part | What the listing states | Price checked November 18, 2026 |
|---|---|---|
| F/R Differential Gear for 1:10 Scale Cars (31007) | Front or rear differential, 1:10 cars, part number 31007, includes bearing | $18.99 |
| Aluminum Sealed Differential Case with Steel Main Gear, 1/10 Rustler / Slash / Stampede 2WD | Sealed case with steel main gear, 1/10 Rustler, Slash, Stampede 2WD including VXL and XL-5, plus Bandit, per listing; fill with diff fluid, reuse stock diff gears | $23.99 |
| RC Crawler Drive Shafts, 105-155mm, 2-Pack, Hardened 45 Steel, SCX10, GEN7, D90 | 105 to 155 mm CVD shafts, 2-pack, hardened 45 steel, fits 1:10 SCX10, Redcat GEN7 and GEN7 Pro, 4WD D90, per listing | $28.99 |
| Aluminum Central Drive Shaft Propeller Joint Set, Blue, Tamiya TT02 | 140 mm main shaft, 53 mm joint cups, 6061-T6 aluminum, fits 1/10 Tamiya TT02 chassis, per listing | $18.99 |
| Aluminum 380 to 540 Motor Conversion Mount Adapter, Black or Silver, RC Model Cars | Mounts a 540 motor in place of a 380 motor, slotted holes for fore and aft gear mesh adjustment, about 5 g | $13.99 |
Measure a driveshaft by its working length range and its joint ends, not by the car scale. The crawler shafts above span 105 to 155 mm, so measure your installed shaft at ride height and at full droop, and confirm the replacement range covers both. For the TT02 set, the listing gives a fixed 140 mm shaft and 53 mm cups, so measure the old shaft and cups and compare directly. For a differential, match the part number first, then check that the case, gears, and bearings in the listing match what comes out of your car. The sealed case above reuses your stock differential gears, per the listing, so count and inspect those gears before you order the case alone.
Gear mesh is the last drivetrain check. A motor mount adapter that changes motor size changes the mesh, and the 380 to 540 adapter listing states its slotted holes allow fore and aft adjustment for proper gear mesh. Set the mesh with the paper test the manual describes for your car, then roll the drivetrain by hand and listen for tight spots through a full rotation before you power it.
How do you match wheels, tires, and hex hubs?
Wheel hex size is a starting point, not a final answer. A wheel can slide onto the hex and still be wrong: offset, rim diameter, tire outside diameter, and width decide clearance, gearing feel, and steering load. Confirm the hex, the tire outside diameter, the width, the offset where the listing states it, and the intended class, then turn the steering lock to lock and cycle the suspension by hand after fitting.
| Wheels or hubs | Measurements, per listing | Price checked November 18, 2026 |
|---|---|---|
| 1:10 RC Drift Wheels and Hard Plastic Tires, 4-Piece Set, 12mm Hex, Black | 12 mm hex, tire OD 63 mm, width 26 mm, hard plastic tires, not glued | $26.99 |
| 1:10 Pre-Glued On-Road Wheels and Rubber Tires, 4-Piece Set, 12mm Hex, Color D | 12 mm hex, tire OD 65 mm, width 26 mm, 4 mm axle hole, pre-glued, foam inserts, 4 locknuts | $23.99 |
| 1:10 On-Road Tires and Aluminum Wheels, 4-Piece Set, 12mm Hex, Black, Foam Inserts | 12 mm hex, OD 65 mm, width 27 mm, offset about -5 mm, foam inserts, tires not pre-glued | $44.99 |
| Aluminum 12mm Drive Hub Adapter Hex 5-12mm, 4-Pack with Screws and Bolts | 12 mm hex, thickness 5 to 12 mm by option, 4 adapters with screws and bolts | $6.33 to $7.99 by thickness and color |
Read the glued line before you buy. The pre-glued set arrives ready to mount, while the hard plastic drift tires and the aluminum wheel set arrive unglued, per their listings, so budget glue and curing time for those. Read the offset line too: the aluminum set states an offset of about -5 mm, which changes track width and steering feel against a zero offset wheel of the same diameter. Hub adapters change track width by thickness, and the adapter listing spans 5 to 12 mm across 24 options, all in stock at $6.33 to $7.99. Measure your current hub thickness and the clearance to the steering link and shock spring before you pick a thicker adapter.
How do you measure shocks and suspension parts?
Shock length is measured mount to mount, eye to eye, at the length the listing states. Overall length and mount to mount length are different numbers, and mixing them up orders the wrong shock. The 70mm Adjustable Aluminum Oil Shocks for 1/16 RC Cars listing states both: 70 mm overall length and 63 mm mount to mount, sold as a pair. Measure your old shock the same way, eye center to eye center, and compare the mount to mount figure.
| Shock or suspension part | Length and fitment, per listing | Price checked November 18, 2026 |
|---|---|---|
| 70mm Adjustable Aluminum Oil Shocks for 1/16 RC Cars | 70 mm overall, 63 mm mount to mount, pair, 1/16 cars | From $15.97 (in stock colors) |
| 81mm Oil Shocks, 4-Piece Set, Black and Red, for 1:12, 1:14, and 1:16 RC Cars | 81 mm, 4-piece set, threaded aluminum bodies, fits listed MJX, WLtoys, SCY, and HBX 1:12 to 1:16 cars, per listing | $25.99 |
| INJORA 90mm Shock Absorbers for 1:10 RC Crawlers, 4-Piece Set, Black and Red, No Oil | 90 mm, 4-piece set, spare springs and screws, shipped without oil, fits listed Axial SCX10, TRX-4, and D90, per listing | $38.99 |
| Oil Shock Absorber Set for 1:10 Traxxas Slash, Stampede, Rustler, Hoss, Bandit, Blue | Oil-filled big bore set, threaded aluminum bodies, fits listed Traxxas 1:10 trucks, part 5862, per listing | $40.99 |
| Rear Shock Tower for 1:10 Scale Cars (31004) | Rear shock tower, 1:10 cars, part number 31004 | $11.99 |
Check the oil line before you order. The 90 mm crawler set ships without oil, per its listing, so you need shock oil on hand. The Traxxas set is oil-filled, per its listing. Check the mount hardware too: a shock tower is a part number match, and the 31004 tower listing warns to match the number against your manual. After fitting shocks, cycle the suspension through full travel by hand and check that tires clear the body, links clear the driveshafts, and nothing binds at full droop or full compression.
For the 70 mm shocks, note the color options: in stock colors run $15.97 to $16.65, while the red and purple options were on backorder at $27.99 when checked November 18, 2026, so this guide quotes the in stock colors only. Check the exact color option on the listing before you order, because color options can change stock status independently.
How do you identify screws and small hardware?
Remove one clean example of the screw from the same location when you can. Measure the thread diameter, the length below the head, and the head type, and check the thread pitch where the manual states it. Many 1/10 cars use M3 hardware as a baseline, but baseline is not proof: hinge pins, pivot balls, and shock mounts can use different diameters on the same car. A bearing must match inside diameter, outside diameter, and width, plus the shield and flange arrangement for its seat. Photograph the assembly before you strip it, and lay the old parts out in order so each replacement maps to one location.
Where a part carries no visible number, the manual exploded view is the identifier. Find the assembly in the view, read the part number beside the drawing, and search that number. If the manual is missing, measure every interface on the old part and compare all of them to the listing, not just one: a driveshaft needs length and joint ends, a wheel needs hex and diameter and offset, a shock needs mount to mount length and mount hole size. One matching number is a clue, and all matching numbers are a fit.
Compatibility and limitations
Fitment lines in listings are claims about the listed models, and this guide repeats them as listing statements, not as independent test results. Where a listing states a model list, check your exact model and version against that list, including 2WD versus 4×4 and any generation note. Where a listing states a part number, match the number, not the model name. Where a listing states neither, measure the old part and compare every interface dimension in the listing before you order.
Limits apply. Tire diameter changes effective gearing and steering load, so a larger tire is not a free upgrade. Thicker hub adapters change track width and bearing load. Longer shocks change ride height and droop, and a shock that is too long can bottom out the drivetrain or bind the links. A sealed differential case that reuses stock gears needs those gears in good shape, and it needs diff fluid, per the listing. None of the parts in this guide were bench tested for this article: the measurements and fitment lines come from the live listings, checked November 18, 2026, and your manual and caliper are the final check.
RC car replacement parts checklist
- Write down the car make, model, scale, version, and 2WD or 4×4 layout.
- Find the part number in the manual exploded view for the exact assembly.
- Remove the old part and measure every interface: length, hex, bore, hole spacing, thread.
- Compare the part number first, then every measurement, against the listing.
- Check the glued, oil, and included hardware lines so the order is complete.
- Fit the part, cycle steering and suspension by hand, and check all clearances.
- Set gear mesh where a motor or mount changed, and re-check fasteners after the first run.
Frequently asked questions
Does 1:10 scale guarantee a part fits my 1:10 car?
No. Scale is a clue, not proof. Chassis family, version, and the interface dimensions decide fit. Match the part number and measure the old part before you order.
How do I measure shock length correctly?
Measure eye center to eye center, mount to mount. Compare that figure to the listing mount to mount figure, not to overall length. The 70 mm listing in this guide states 70 mm overall and 63 mm mount to mount.
What if the wheel fits the hex but rubs the steering link?
Check offset, tire diameter, and hub thickness. A wheel can fit the hex and still be wrong on offset or diameter. Compare all three numbers to the old wheel before you order a replacement.
Can I use a longer driveshaft than the old one?
Only when the working range covers your installed length at ride height and at full droop, and the joint ends match. The crawler shafts in this guide span 105 to 155 mm, so measure both ends of your travel.
What do I check when a listing says the part reuses stock gears?
Inspect the stock gears for wear, chips, and missing teeth, and confirm the case accepts them. The sealed differential case in this guide reuses stock diff gears and needs diff fluid, per the listing.
What if my car model is not in the listing fitment list?
Do not order on scale alone. Match the part number in your manual, or measure every interface on the old part and compare all of them to the listing. If any measurement is missing from the listing, hold the order and ask with the model name and the measurements in hand.
Parts used in this guide
Every link below opens a live catalog page, checked on November 18, 2026.
- Drivetrain: F/R Differential Gear for 1:10 Scale Cars (31007) ($18.99), Aluminum Sealed Differential Case with Steel Main Gear, 1/10 Rustler / Slash / Stampede 2WD ($23.99), RC Crawler Drive Shafts, 105-155mm, 2-Pack, Hardened 45 Steel, SCX10, GEN7, D90 ($28.99), Aluminum Central Drive Shaft Propeller Joint Set, Blue, Tamiya TT02 ($18.99), Aluminum 380 to 540 Motor Conversion Mount Adapter, Black or Silver, RC Model Cars ($13.99)
- Wheels and hubs: 1:10 RC Drift Wheels and Hard Plastic Tires, 4-Piece Set, 12mm Hex, Black ($26.99), 1:10 Pre-Glued On-Road Wheels and Rubber Tires, 4-Piece Set, 12mm Hex, Color D ($23.99), 1:10 On-Road Tires and Aluminum Wheels, 4-Piece Set, 12mm Hex, Black, Foam Inserts ($44.99), Aluminum 12mm Drive Hub Adapter Hex 5-12mm, 4-Pack with Screws and Bolts ($6.33 to $7.99)
- Shocks and suspension: 70mm Adjustable Aluminum Oil Shocks for 1/16 RC Cars (from $15.97, in stock colors), 81mm Oil Shocks, 4-Piece Set, Black and Red, for 1:12, 1:14, and 1:16 RC Cars ($25.99), INJORA 90mm Shock Absorbers for 1:10 RC Crawlers, 4-Piece Set, Black and Red, No Oil ($38.99), Oil Shock Absorber Set for 1:10 Traxxas Slash, Stampede, Rustler, Hoss, Bandit, Blue ($40.99), Rear Shock Tower for 1:10 Scale Cars (31004) ($11.99)
- Categories: RC Cars and Trucks, Car and Truck Parts, Drivetrain and Gears, Shocks and Suspension, Wheels and Tires
- Related guides: Best RC Car Drivetrain Upgrades in the USA, Best RC Car Wheels and Tires in the USA, Best RC Car Shocks and Suspension in the USA
Shipped fast and securely from our secure facility in New York, providing fast, high quality USA shipping.
Sources
- RC Car Parts Compatibility Guide (ModelPress): compatibility starts with the part number, scale is a clue not proof, and a replacement must attach, clear moving parts, and preserve geometry.
- Quality RC Parts catalog listings, checked November 18, 2026: part numbers, measurements, fitment lists, glued and oil lines, and prices come from live listings. Fitment lines are repeated as listing statements.
