Servo Replacement Measurements: Match Size, Torque, and Spline

Servo Replacement Measurements: Match Size, Torque, and Spline

Servo replacement measurements start with the old servo in your hand: case length, width, and height, mounting hole spacing, spline tooth count, arm length, and lead length. Match those numbers to the new listing before you compare torque or speed, because a stronger servo that does not fit the bay or the horn is still the wrong part.

Last updated: November 18, 2026. Prices in this guide were checked on that date.

What servo replacement measurements matter first?

Measure the failed servo before you shop. Seven numbers decide fit, and every one of them comes from the part itself or from the model manual. The table below lists each measurement, how to take it, and what goes wrong when it is skipped.

Measurement How to take it If you skip it
Case length, width, height Caliper across the case body, without the mounting ears Servo will not fit the bay or the mount
Mounting hole spacing Center to center across the mounting ears Screws miss the tray or the bracket
Spline tooth count Mark one tooth, count around the output shaft Old horn will not fit the new output
Output shaft diameter Caliper across the spline, outside of the teeth Horn fits loose or will not press on
Arm length Center of the spline to the linkage hole you use Throw and force change at the surface
Lead length and connector Case exit to plug end, plus plug style Lead will not reach the receiver
Torque and speed at voltage Read the listing values at one stated voltage New servo stalls or centers worse than the old one

Write the numbers down in that order. A photo of the old servo next to a ruler helps when the manual is missing, but the caliper numbers decide the order. Check the bay as well as the servo: measure the opening in the wing, fuselage, or chassis tray, and check clearance for the lead exit and the arm swing.

How do size classes compare on live listings?

Size class names such as micro, mini, and standard describe the case, not the torque. The listings below show how much the case and the torque vary inside one class, which is why the measured dimensions matter more than the class name. All torque and speed values below come from the live listings, at the voltages the listings state.

Servo Case size Torque and speed, per listing Price checked November 18, 2026
SG92R Analog Plastic Composite Gear Micro Servo 23.0 x 12.2 x 29 mm, 9 g 2.5 kg/cm at 4.8V; 0.1 sec/60deg at 4.8V $8.00
DSM-44 Digital Metal Gear Micro Servo 22 x 8.7 x 22 mm, 5.8 g 1.6 kg/cm at 6.0V; 0.07 sec/60deg at 6.0V $22.00
Towerpro MG92B Digital Metal Gear Micro Servo 22.0 x 12.0 x 31.0 mm, 13.8 g 3.5 kg-cm; 0.11 sec/60deg at 6.0V $17.00
1250MG Metal Gear 25g Mini Servo 31.0 x 16.3 x 29.5 mm, 25 g 3.0 kg-cm at 4.8V, 3.5 kg-cm at 6.0V; 0.14 sec at 4.8V, 0.12 sec at 6.0V $18.00
Perfex KS-201 Standard Servo 40.5 x 20 x 36.5 mm, 42 g 3 kg/cm at 4.8V, 4.5 kg/cm at 6.0V; 0.18 sec $8.60
20KG Waterproof Digital Servo Standard, 40 x 20 x 38 mm class 20KG torque, digital, waterproof sealed case, 25T spline $53.99
20KG Digital Servo, 270 Degree, Waterproof, Full Metal Gear, DS3218MG 40 x 20 x 40.5 mm, 60 g Up to 21.5 kg.cm at 6.8V; 270 degrees controlled rotation $23.99
SPT4412 12KG Digital Servo, Metal Gear, High Torque for 1:10 RC Drift Car, Airplane, Boat 41 x 20.3 x 28 mm, about 68 g 10 kg.cm at 4.8V, 12 kg.cm at 6.0V; 0.11 sec/60deg at 4.8V, 0.09 sec/60deg at 6.0V $34.99

Two lessons stand out. First, micro servos are not one size: the DSM-44 is 8.7 mm wide and 5.8 g, while the MG92B is 12.0 mm wide and 13.8 g, so a micro bay cut for one may not hold the other. Second, standard servos are not one torque: the KS-201 lists 3 kg/cm at 4.8V and the DS3218MG lists up to 21.5 kg.cm at 6.8V, both in standard size cases. Read the listing, not the class name.

The Micro Servo SG90 / SG92R / MG90S listing offers three 9 g micro models in one listing: SG90 with plastic gears at $19.99, and SG92R with carbon gears and MG90S with metal gears at $13.99 each, all checked November 18, 2026. The listing states 9 g micro size and a standard 3-wire JR plug, and it does not state case dimensions, torque, or spline count, so match those three models by the gear type and by the separate SG92R listing values above, and check the listing again before you order. The MG996R Metal Gear Servo at $15.99 is listed as a metal gear standard servo, and its listing also does not state dimensions or torque numbers. That gap is noted here rather than filled with a guess: if the MG996R is your target, confirm its case size against your bay from the manual or from the part in hand.

How do you count spline teeth and match a horn?

The spline is the toothed output shaft that the servo arm or horn presses onto. Tooth count and shaft diameter must both match the horn, or the horn will fit loose, strip, or refuse to press on. Count the teeth on the old servo output: mark one tooth with a fine pen, then count each tooth around the shaft until you return to the mark. Measure the shaft diameter across the outside of the teeth with a caliper. A 25 tooth spline is common on standard servos, and several live listings state 25T outright, but tooth count alone is not proof: the shaft diameter must match too.

The 20KG Waterproof Digital Servo listing states a 25T spline output, and the DS3218MG listing states a 25T aluminum horn is included. The metal arm listings below state 25 tooth fitment for standard servos, with fitment notes naming Futaba, Power HD, and Towerpro 25T spline servos, per the listings. Use the listing fitment line, not a general rule, when you pick an arm.

Arm or horn Length or size, per listing Price checked November 18, 2026
1-1/2in Metal Servo Arm, 25T 1-1/2 in, 25 tooth, metal $4.99
1.85in Metal Servo Arm, 25T About 1.85 in (47 mm), 25T, metal $5.99
2-1/4in Metal Servo Arm, 25T 2-1/4 in, 25 tooth, metal $11.99
25T Aluminum Servo Horn, M3 Threads, Metal Steering Arm, Single (Black) 25T aluminum horn, M3 threads, single $2.99
Metal Servo Disk for Standard Servos, 5-Pack 20 mm disk, M3 mount holes, 25T, 5 disks and 5 screws $7.99

Arm length changes the linkage. A longer arm gives more surface travel per degree of servo rotation and less force at the linkage, while a shorter arm gives less travel and more force. The 1-1/2 in arm listing states it gives strong mechanical advantage for control surfaces that need authority, and the 1.85 in listing states the longer arm gives more surface travel per degree. Match the arm length to the hole position you used on the old arm, then check full travel on the bench before the first run. For a fuller walkthrough of arms, horns, and centering, read How to Fit Servo Arms, Horns, and Testers for RC Use.

Micro servo splines are a gap in the listings used here: the SG92R, DSM-44, MG92B, and 1250MG listings state dimensions and torque but do not state spline tooth counts. Do not assume a standard 25T horn fits a micro servo. Match micro horns by the servo model and by the horn listing fitment line, and count the teeth on the old output before you order.

How do torque and speed readings mislead?

Torque without a voltage is not a comparison. The SPT4412 lists 10 kg.cm at 4.8V and 12 kg.cm at 6.0V, and the 1250MG lists 3.0 kg-cm at 4.8V and 3.5 kg-cm at 6.0V, so the same servo reads higher at the higher voltage. Compare candidates at the voltage your receiver or BEC actually supplies, and check the listing for the value at that voltage. Speed works the same way: the SPT4412 lists 0.11 sec/60deg at 4.8V and 0.09 sec/60deg at 6.0V. A speed quoted without a voltage tells you nothing about the servo on your setup.

Stall torque is the peak the servo reaches at rated voltage just before it stalls. It is the right basis for sizing, and the wrong basis for a joint that must hold position for long periods under load, because heat and duty cycle cut into what the servo can hold. Size with margin: if the old servo stalled or faded on the job, step up in torque at the same case size where the bay allows it, and check that the arm length and linkage geometry still give the travel you need. Servo Torque Math: How to Size Servos for Control Surfaces walks through the load times arm length method for control surfaces.

What about mounts, leads, and rotation?

Three fitment details sit outside the servo itself. First, the mount: the CNC Aluminum Alloy Servo Mount Bracket, U-Shaped Holder for Standard Servos (S3003 / MG995 / MG996R) at $8.99 measures 55 x 26 mm and lists fitment for standard size servos in the Futaba S3003 and MG995 and MG996R class, with screws included and the servo not included. A two set version, the CNC Aluminum Alloy Servo Mount Bracket 2-Set with M3 Screws, for Standard Servos (S3003 / MG995), costs $14.99. Measure the bracket footprint against the chassis or frame before you order, and confirm the servo case fits the U-shaped holder.

Second, the lead: the SPT4412 listing states a JR connector with a 260 mm wire length. If the receiver sits farther from the servo than the lead reaches, an extension solves it, but length and wire gauge both matter. The Universal Servo Extension 6in, 26AWG, 5-Pack at $7.20 covers short runs with universal Futaba and JR style connectors, while the Heavy-Duty Universal Servo Extension 12in, 22AWG, 5-Pack at $5.99 uses thicker 22AWG wire for longer runs and higher current servos. The 12 in listing warns that voltage drop over long extensions is real, especially with digital servos. Route the extension away from sharp edges, and check the servo still centers and holds under load after the extension goes in.

Third, rotation: most servos in this guide are standard travel servos, but the DS3218MG listing states 270 degrees of controlled rotation, turning a full 360 degrees when powered off. A 270 degree servo changes endpoint setup and linkage travel, so check the rotation figure in the listing before you treat it as a drop-in replacement for a standard travel servo. Waterproofing is also a listing claim, not a size class: the 20KG servo and the DS3218MG both list waterproof sealing, while the micro listings above make no waterproof claim. If the job gets wet, pick a listing that states waterproof sealing, and read How to Choose a Waterproof Servo for RC Cars and Boats for the tradeoffs.

Compatibility and limitations

Compatibility starts with the plug and the voltage. The listings here state JR style or universal Futaba and JR style connectors for the servos and extensions named, which covers the common 3-wire servo plug, but always check the plug line in the listing for the exact part you buy. Check the receiver or BEC voltage against the servo listing: the SPT4412, 1250MG, and KS-201 listings give values at 4.8V and 6.0V, and the DS3218MG lists its peak torque at 6.8V, so a 4.8V supply will not deliver the 6.0V or 6.8V figures. Do not run a servo above the top of its stated voltage range to recover torque.

Limitations are real. No listing used here states a spline count for a micro servo, so micro horn fitment needs a tooth count from the old part. The MG996R and SG90 listings used here do not state case dimensions or torque, so they cannot anchor a measurement comparison. Gear material is stated in the listings and matters under shock loads: metal gears survive hits that strip plastic gears, per the MG996R listing, while plastic composite gears keep weight down on small planes. Digital versus analog is also stated in the listings: the DSM-44, MG92B, SPT4412, and DS3218MG list digital control, and the SG92R lists analog control. Digital servos generally center and hold more firmly and draw more current, which makes the extension gauge and the power supply part of the fitment check, not an afterthought.

Servo replacement checklist

  1. Remove the old servo and measure case length, width, and height, plus mounting hole spacing.
  2. Count the spline teeth, measure the shaft diameter, and record the arm length to the linkage hole you use.
  3. Measure the lead length and note the connector style, then measure the run to the receiver.
  4. Read the old listing or manual for torque and speed at one voltage, and note your supply voltage.
  5. Pick a replacement that matches case size, spline, and arm length first, then torque at your voltage.
  6. Check rotation, waterproofing, gear material, and digital or analog control in the new listing.
  7. Order the matching horn or arm, mount, and extension in the same order when any of them changes.
  8. Center the servo on the bench, fit the arm, and check full travel and linkage clearance before the first run.

Frequently asked questions

What if the new servo case is 1 mm larger than the old one?

Do not force it. A 1 mm difference can bind the case in a molded bay or shift the arm plane enough to bind the linkage. Pick a listing whose stated dimensions match the bay, or fit a mount bracket that holds the larger case in the right position.

Can I reuse the old horn on a new servo?

Only when the tooth count and the shaft diameter both match. Count the teeth on both outputs and measure both shafts. A 25T horn fits a 25T output of the matching diameter, and a micro output needs a model matched horn.

Why does the same servo list two torque figures?

Torque rises with voltage, so listings give values at two voltages, such as 4.8V and 6.0V. Compare servos at the voltage your setup supplies, and use the figure for that voltage.

Does a longer servo arm give more power?

No. A longer arm gives more travel per degree of servo rotation and less force at the linkage. A shorter arm gives less travel and more force. Match the arm length to the travel and force the job needs.

Do I need a heavy duty extension for a long wing run?

For long runs and higher current digital servos, thicker wire holds voltage up better. The 12 in 22AWG extension listing states it suits longer runs and higher current servos, while the 6 in 26AWG listing suits short runs. Check centering under load after fitting any extension.

What if the listing does not state the spline count?

Count the teeth on the old servo and measure the shaft, then match by the servo model and the horn listing fitment line. Do not assume a standard 25T horn fits, especially on micro servos.

Parts used in this guide

Every link below opens a live catalog page, checked on November 18, 2026.

Shipped fast and securely from our secure facility in New York, providing fast, high quality USA shipping.

Sources