
How to Choose N20 Micro Gear Motors for a Small Robot
Choose an N20 micro gear motor by voltage and speed. The 3 V to 6 V motor turns 52 RPM at 3 V and 104 RPM at 6 V. The 12 V motor turns 100 RPM. Both use a full metal gearbox and a 3 mm D-type shaft. Pair either motor with a dual H-bridge driver board.

Quick facts
| Fact | Value |
|---|---|
| 3 V to 6 V motor | 52 RPM at 3 V, 104 RPM at 6 V, $5.49 |
| 12 V motor | 100 RPM, 40 mA no-load current, $4.99 |
| Gearbox | Full metal gearbox on both motors |
| Shaft | 3 mm D-type shaft, 9 to 10 mm long |
| Motor size | 24 x 12 x 10 mm (3 V to 6 V motor) |
| L298N driver | 5 to 35 V supply, up to 2 A per channel, $6.99 |
| TB6612FNG driver | 2.7 to 10.8 V input, 1.2 A per channel, $15.99 |
Which N20 motor fits a 3 V to 6 V robot?
The 3 V to 6 V N20 motor fits small battery robots that run on 3 V to 6 V.
It turns 52 RPM at 3 V and 104 RPM at 6 V, so speed rises with voltage.
Its full metal gearbox gives strong torque for its size at slow speeds.
The motor measures 24 x 12 x 10 mm and draws 0.04 A with no load.
When do you need the 12 V N20 motor?
The 12 V N20 motor fits robots that already run on a 12 V battery.
It turns 100 RPM at 12 V and shares the same 12 mm body and 3 mm shaft.
Its no-load current is 40 mA, and it uses the same full metal gearbox.
Do not run the 12 V motor on 3 V to 6 V; it will turn too slowly to drive a wheel.
How do you drive an N20 motor from an Arduino board?
A microcontroller pin cannot drive a motor directly, so use a driver board.
The L298N board runs two DC motors at 5 to 35 V and up to 2 A per channel.
The TB6612FNG module runs two DC motors at 2.7 to 10.8 V and 1.2 A per channel.
Both boards take speed control through PWM inputs and direction through logic inputs.
What size wheels and mounts fit an N20 motor?
The 3 mm D-type shaft fits small wheels, pulleys, and couplings made for N20 motors.
The 3 V to 6 V motor shaft is 9 mm long, and the 12 V motor shaft is 10 mm long.
Both motors fit robot car chassis, line followers, and grippers that take an N20 mount.
Check the mount spacing before you order, since N20 bodies measure 12 mm across.
What did we check on the bench?
We matched every price in this guide to the live store price on November 20, 2026.
We checked the 3 V to 6 V listing states 52 RPM at 3 V and 104 RPM at 6 V. It also states a 3 mm D-type shaft.
We checked the 12 V listing states 100 RPM, 40 mA no-load current, and a 12 mm by 26 mm body.
We checked the L298N listing states a 5 to 35 V supply and up to 2 A per channel.
How the options compare
| Item | Voltage | Speed | Price |
|---|---|---|---|
| N20 motor, 3 V to 6 V | DC 3 to 6 V | 52 RPM at 3 V, 104 RPM at 6 V | $5.49 |
| N20 motor, 12 V | DC 12 V | 100 RPM | $4.99 |
| L298N driver board | 5 to 35 V supply | Up to 2 A per channel | $6.99 |
| TB6612FNG driver, 3-pack | 2.7 to 10.8 V input | 1.2 A per channel | $15.99 |
How do you wire an N20 motor to a driver in 6 steps?
- Pick the motor that matches your battery: 3 V to 6 V, or 12 V.
- Connect the red and black motor leads to one driver output channel.
- Connect the driver supply input to your battery within its voltage range.
- Connect the driver logic inputs and PWM pin to your microcontroller board.
- Power the board and test the motor at low speed first.
- Check the wheel turns the right way, then swap the two motor leads if it runs backward.
Parts that fit this guide
In-stock parts ship from the New York, USA warehouse in 1-2 business days. Prices below are the live store prices we verified on November 20, 2026.
N20 Micro Gear Motor DC 3V-6V, Full Metal Gearbox, 52 RPM, Single ($5.49)
N20 Micro Gear Motor DC 3V-6V at $5.49. It turns 52 RPM at 3 V and 104 RPM at 6 V. It has a full metal gearbox and a 3 mm D-type shaft 9 mm long.
N20 Micro Gear Motor DC 12V 100 RPM, Full Metal Gearbox, GA12-N20, Single ($4.99)
N20 Micro Gear Motor DC 12V 100 RPM at $4.99. It runs on 12 V at 100 RPM with a full metal gearbox, a 3 mm shaft, and a 12 mm by 26 mm body.
HiLetgo L298N Motor Driver Board, Dual H-Bridge DC and Stepper Motor Controller for Arduino ($6.99)
HiLetgo L298N Motor Driver Board at $6.99. It drives two DC motors at 5 to 35 V and up to 2 A per channel, with ENA and ENB PWM speed inputs.
TB6612FNG Dual DC/Stepper Motor Driver Module, 3-Pack ($15.99)
TB6612FNG Dual DC/Stepper Motor Driver Module, 3-Pack at $15.99. Each module drives two DC motors at 2.7 to 10.8 V and 1.2 A continuous per channel, with a low power sleep mode.
Shop the full range: Robot Motors & Drivers at Quality RC Parts. See also: Related guide.
Frequently asked questions
Can I run an N20 motor straight from an Arduino pin?
No. A microcontroller pin cannot supply motor current. Use a driver board such as the L298N or TB6612FNG between the board and the motor.
What voltage should I run a 3 V to 6 V N20 motor on?
Run it on 3 V to 6 V. It turns 52 RPM at 3 V and 104 RPM at 6 V, so pick the voltage that gives the speed your robot needs.
How do I reverse an N20 motor?
Swap the two motor leads, or flip the direction logic inputs on the driver board. The driver handles direction, so you never swap the battery wires.
Which driver fits a 3 V to 6 V N20 motor?
The TB6612FNG fits, since its input starts at 2.7 V. The L298N also works, but its supply range starts at 5 V.
Sources
Last updated: November 20, 2026.
