
Twelve new encoder and motor parts landed at Quality RC Parts, and they cover the whole closed-loop chain: magnetic encoder modules that report shaft angle, brushless gimbal motors with encoders built in, small N20 gear motors for robots, the wire to connect them, and a pan-tilt servo bracket to mount the result. This guide explains what each part does and how the pieces fit together. All twelve are live in the store now, shipped fast and securely from our secure facility in New York, providing fast, high quality USA shipping.
The twelve new parts at a glance
| Part | What it is | Price |
|---|---|---|
| AS5600 Magnetic Encoder 1-Pack | 12-bit absolute position sensor, I2C and PWM, white module | $5.49 |
| AS5600 Magnetic Encoder 3-Pack | Three 12-bit AS5600 modules | $6.99 |
| AS5048A Magnetic Encoder, Teyleten | 14-bit absolute angle sensor, PWM, SPI, I2C | $20.99 |
| AS5047P Encoder Module | 14-bit SPI, ABZ, PWM rotary position sensor | $17.99 |
| AS5048A Encoder Module | 14-bit PWM, SPI, I2C angle sensor | $22.99 |
| 2804 Hollow Shaft Outrunner with AS5600 | Brushless gimbal motor and encoder kit, FOC | $38.99 |
| C2208-100T Brushless Motor with MT6701 | Brushless motor with magnetic encoder, FOC gimbal | $38.99 |
| 4015 BLDC Gimbal Motor with AS5600 | Hollow shaft outrunner, 12 to 36V | $58.99 |
| SCHDRA UL1007 Hook-Up Wire Kit | 26 AWG PVC wire, 6 colors, 20 ft each, tinned copper | $12.99 |
| N20 Micro Gear Motor, 3V to 6V | Full metal gearbox, 52 RPM, single | $5.49 |
| N20 Micro Gear Motor, 12V | Full metal gearbox, 100 RPM, single | $4.99 |
| Pan Tilt Servo Mount Bracket, 2 Sets | Aluminum bracket for MG996R, MG995, S3003 standard servos | $20.99 |
AS5600: the 12-bit encoder, two ways to buy it
The AS5600 is a 12-bit magnetic absolute position sensor. A small diametrically magnetized magnet sits on the shaft, the sensor reads the field angle, and it reports the position over I2C or PWM. Absolute means it knows where it is at power-on, with no homing move. That is what a gimbal motor, a robot joint, or a steering sensor needs.
Two listings cover it. The AS5600 Magnetic Encoder Module, 12-Bit Absolute Position Sensor, I2C PWM, 1-Pack is $5.49, a white module with I2C and PWM. The AS5600 Magnetic Encoder Module, 12-Bit Absolute Position Sensor, I2C PWM, 3-Pack is $6.99 for three of the white modules, which is the buy for a multi-joint build or a bench stock of spares.
AS5048A and AS5047P: 14-bit encoders
The AS5048A Magnetic Encoder, 14-Bit Absolute Angle Sensor, PWM SPI I2C is $20.99, and the AS5048A Magnetic Encoder Module, 14-Bit PWM SPI I2C Angle Sensor is $22.99. Both are 14-bit AS5048A modules, which report angle with four times the resolution steps of a 12-bit part. They speak PWM, SPI, and I2C. The two listings are different boards from different sellers, so check the pinout on the listing that matches the board you receive before you wire it.
The AS5047P Encoder Module, 14-Bit SPI ABZ PWM Rotary Position Sensor is $17.99. The AS5047P is also 14-bit, and it adds ABZ incremental outputs alongside SPI and PWM. ABZ is the quadrature output that motor drivers and motion controllers expect, so this is the module for a controller that wants encoder pulses instead of an absolute angle read over a bus.
Gimbal motors with encoders built in
The 2804 Hollow Shaft Outrunner Brushless Motor with AS5600 Encoder Kit, FOC Gimbal is $38.99. It is a 2804 hollow shaft outrunner with an AS5600 encoder, built for field-oriented control on a gimbal. The hollow shaft passes wires or a camera cable through the motor axis, which is how a gimbal keeps its wiring tidy while the motor turns.
The C2208-100T Brushless Motor with MT6701 Magnetic Encoder, FOC Gimbal is $38.99. The C2208-100T is a brushless motor paired with an MT6701 magnetic encoder, also built for FOC gimbal work. The MT6701 is a different encoder chip from the AS5600, so this motor suits a controller or firmware setup that already supports the MT6701, or a builder comparing encoder chips side by side.
The 4015 BLDC Gimbal Motor with AS5600 Encoder, Hollow Shaft Outrunner, 12-36V is $58.99. The 4015 is the larger motor in this group, a hollow shaft outrunner rated 12 to 36V with an AS5600 encoder. Larger diameter means more torque at low speed, which is what a heavy camera gimbal needs. Only one is in stock at this price.
N20 gear motors and hook-up wire
The N20 Micro Gear Motor DC 3V-6V, Full Metal Gearbox, 52 RPM, Single is $5.49, and the N20 Micro Gear Motor DC 12V 100 RPM, Full Metal Gearbox, GA12-N20, Single is $4.99. Both are single N20 micro gear motors with full metal gearboxes, sold as one motor each instead of a three-pack. The 3V to 6V motor runs at 52 RPM, and the 12V motor runs at 100 RPM. N20 motors are the standard drive for small robots, grippers, and pan-tilt mechanisms. Pick the voltage that matches your battery and driver, and check the RPM against the speed your mechanism needs: a 52 RPM motor turns a wheel slowly with more torque, while a 100 RPM motor trades torque for speed.
The SCHDRA UL1007 26 AWG PVC Hook Up Wire Kit, 6 Colors x 20 ft Tinned Copper is $12.99. Six colors, 20 feet each, 26 AWG tinned copper. Color-coded wire is how a multi-motor build stays debuggable: one color per signal, so a wiring fault is visible instead of a puzzle.
Mounting it: pan-tilt servo bracket
The 2 Sets Pan Tilt Servo Mount Bracket for MG996R MG995 S3003 Standard Servos, Aluminum Alloy is $20.99 for two sets. The aluminum bracket holds standard servos like the MG996R, MG995, and S3003 in a two-axis pan-tilt mount. It is the frame that turns a pair of servos and a camera or sensor into a pointing mechanism, and the same bracket works as the mount for a small N20-driven mechanism.
How the pieces fit together
A closed-loop build has three parts: a motor, an encoder on the motor shaft, and a controller that reads the encoder and drives the motor. The encoder modules above are the middle piece for a motor you already own. The gimbal motors have the encoder already mounted, so they are the shortcut when you want the pair together. The N20 gear motors have no encoder, so they run open loop unless you add one. The AS5600 and AS5048A modules mount over a shaft magnet, and the magnet gap and alignment decide whether the reading is clean, so mount the magnet centered and check the gap the listing calls for before you power the loop.
