Servo vs Stepper for a Small Robot Arm: Torque, Holding, and Backlash
Servo vs stepper is the first motor decision for a small robot arm, and the answer is usually both. Servos suit joints that need holding torque, simple control, and compact size. Steppers suit joints that need repeatable open-loop motion and smooth rotation. The right pick depends on the joint, the load, and the power budget. This guide compares torque, holding, backlash, and gear reduction joint by joint.
All prices in this post are the effective prices checked November 18, 2026.
Servo vs Stepper: How Each One Works
A hobby servo is a small geared motor with a position sensor and a control circuit built in. You send a pulse signal, and the servo drives to the matching angle and holds it. The feedback loop is inside the servo. Your code says where to go, and the servo handles getting there and staying there. Travel is limited: most hobby servos cover 180 degrees, and some cover 270 degrees.
A stepper motor moves in fixed steps. Each pulse from the driver advances the motor by one step angle. A standard NEMA 17 stepper has a 1.8 degree step angle, which is 200 steps per full turn. The motor can rotate continuously in either direction, and the driver can divide each step into microsteps for smoother motion. There is no built-in position sensor. The controller counts steps and assumes the motor followed. If the load stalls the motor, steps are missed and the assumed position is wrong.
The 28BYJ-48 is a different kind of stepper. It is a small geared stepper with a 1/64 gear reduction built in. The motor itself steps at 5.625 degrees, and the gear train multiplies the step count to about 2038 steps per output revolution. That gearing gives more torque and finer output steps at the cost of speed and gear backlash. The 28BYJ-48 sets sold here include a ULN2003 driver board, which is the correct driver family for this 5-wire unipolar motor.
Holding Position: The Big Difference
A servo holds position with feedback. If the load pushes the arm off angle, the servo drives back. The holding force is limited by the servo torque rating and by heat. A servo held at stall against a heavy load for a long time gets hot. For an arm joint that must hold a load steady, a servo is the simpler choice because the holding behavior is built in.
A stepper holds position with magnetic detent torque when powered. The driver keeps current flowing through the coils, and the rotor resists being pushed off step. That holding torque is real, but it costs power: the driver draws current even when the motor is not moving. If you cut power, the holding torque mostly disappears, and the arm joint can sag under gravity. Some builders add a brake or a counterweight for that case. Others accept that the arm parks when power is off.
For a small arm, the practical rule is simple. Joints that hold a load against gravity for long periods favor servos, because the feedback loop corrects drift and the control is simple. Joints that need to rotate continuously or index to exact step counts favor steppers, because the step count is exact and the rotation has no travel limit.
Torque, Speed, and Gear Reduction
Torque ratings are not directly comparable across families unless you check the conditions. Servo torque is rated in kg-cm at a stated voltage. Stepper torque is rated in Nm or kg-cm at a stated current, and stepper torque falls as speed rises. A stepper that holds strongly at standstill may have little torque left at high speed. A servo torque rating is a stall rating: the maximum at zero speed. Both ratings need margin in real use.
Gear reduction changes everything. The 28BYJ-48 gear train trades speed for torque and resolution. The output turns slowly, but each output step is small and the output torque is multiplied by the gear ratio minus friction losses. A direct-drive NEMA 17 has no gear reduction, so its output torque is the motor torque and its output step is the full 1.8 degrees. Servos also have internal gear trains, which is why a 9 g micro servo can move a light arm at all.
Listing-verified figures make the comparison concrete. The MG90D micro servo is listed at 2.1 kg-cm stall at 4.8V. The DS3218MG digital servo is listed at up to 21.5 kg-cm at 6.8V. The NEMA 17 stepper with 20T gear is listed at 0.36 Nm, 1.2A, with a 5 mm shaft and a weight of 290 g. The NEMA 17 4-pack is listed at 0.22 Nm and 1.3A per motor, 220 g each, with 12V to 24V suggested. Note that the 4-pack motors are lower torque than the single motor. Do not assume all NEMA 17 motors are the same. Check the torque and current on the listing you buy.
| Motor | Listing torque | Step or travel | Best arm use | Price |
|---|---|---|---|---|
| MG90D micro servo | 2.1 kg-cm at 4.8V | Servo travel | Wrist, light gripper | $14.00 |
| MG92B micro servo | 3.5 kg-cm | Servo travel | Wrist, small joints | $17.00 |
| DS3218MG servo | Up to 21.5 kg-cm at 6.8V | 270 degree controlled | Shoulder, elbow, gripper | $23.99 |
| DS3235 servo | 35 kg-cm at 7.4V | 180 degree | Heavy shoulder, elbow | $48.99 |
| NEMA 17 stepper, single | 0.36 Nm, 1.2A | 1.8 degree, 200 steps/rev | Base rotation, linear axes | $9.99 |
| NEMA 17 stepper, 4-pack | 0.22 Nm, 1.3A | 1.8 degree, 200 steps/rev | Multi-axis rigs | $27.99 |
| 28BYJ-48 5V 3-set with ULN2003 | Not stated in listing | About 2038 steps/rev output | Slow pan, light indexing | $12.99 |
| 28BYJ-48 12V 2-set with ULN2003 | Not stated in listing | About 2038 steps/rev output | Slow pan, light indexing | $12.99 |
The listings for the micro servo options SG90 / SG92R / MG90S and the MG996R metal gear servo state gear type and size but no torque figures. They are priced at $13.99 to $19.99 by option and $15.99 respectively. If you size a joint from torque, use a listing that states the torque, or measure the servo you have.
Backlash and Repeatability
Backlash is the free play in a gear train. When the motor reverses direction, the output does not move until the gear teeth take up the slack on the other side. Every geared motor has some backlash. The 28BYJ-48 has noticeable backlash because of its multi-stage 1/64 gear train. Servos have backlash from their internal gears too. A direct-drive NEMA 17 has no gear train, so it has no gear backlash, but it can still lose position by missing steps under load.
Repeatability is different from backlash. Repeatability is whether the joint returns to the same position when commanded to the same target. A servo with feedback returns to the same angle within its deadband, which is the small range the controller treats as close enough. A stepper returns to the same step count exactly, as long as no steps were missed. If steps were missed, the error persists until the motor is re-homed. For pick and place work, both can repeat well. The stepper wins on open-loop repeatability when the load is within its torque. The servo wins when the load varies, because the feedback loop corrects.
Homing is the stepper weakness. After a power cycle, a stepper controller does not know the absolute position. It only knows step counts from wherever it started. Repeatable absolute positioning needs a homing routine: drive to a known reference, such as a limit switch, at startup, then count from there. A servo knows its position within its travel as soon as it powers up, because the internal sensor reads the shaft angle. If your arm must know where it is immediately at power-up with no homing move, servos are the simpler choice.
Power Draw and Heat
A stepper driver draws current whenever the motor is energized, including at standstill. That is how holding torque works. A multi-joint stepper arm can draw significant idle current and heat the drivers. Stepper drivers need current limits set correctly. The A4988 driver module listing states up to 1.2A continuous per phase, adjustable by potentiometer, with a heatsink included, and a motor supply up to 35V. The Pololu carrier page for the A4988 states about 1A per phase without a heatsink and 2A per coil with sufficient cooling. Set the current limit for your motor, fit the heatsink, and check driver temperature under load. Heat is the signal that the current limit or the cooling is wrong.
Quieter stepper drivers exist for the same StepStick footprint. The TMC2208 5-pack costs $25.99 and lists StealthChop2 quiet stepping, up to 1/256 microstepping, 1.2A RMS and 2A peak, and a 4.75V to 36V motor supply. The TMC2209 5-pack costs $29.99 and lists 2A RMS and 2.8A peak, a 4.75V to 28V supply, and StallGuard4 sensorless homing. Sensorless homing detects a stall instead of using a switch, which can simplify a homing routine, but it needs tuning for the motor and load. Neither driver removes the need for a current limit.
Servos draw current in proportion to load. A servo at rest with no load draws little. A servo driving a load or stalled draws much more. The DS3235 listing states stall currents of 1.9A at 5V, 2.1A at 6V, and 2.3A at 7.4V. Size the servo supply for the stall case, and keep servo power separate from the controller supply. The driver-choice detail, including ULN2003, L298N, and TB6612FNG limits, is covered in the companion guide on stepper and DC driver choice.
Joint by Joint: Which Motor Where
| Joint | Usual pick | Why |
|---|---|---|
| Base rotation | Servo or stepper | Servo if the rotation stays inside travel and needs holding. Stepper if continuous rotation or exact indexing matters. |
| Shoulder | Servo, high torque | Holds the full arm weight against gravity. Feedback corrects sag. Size with margin. |
| Elbow | Servo, high torque | Same gravity load as the shoulder, smaller lever arm. Metal gears help. |
| Wrist rotate | Micro servo or small stepper | Light load. A micro servo is simple. A 28BYJ-48 suits slow continuous rotation. |
| Wrist tilt | Micro servo | Small range, light load, needs holding. Micro servo fits the size. |
| Gripper | Servo | Holding and travel fit the servo. See the gripper servo guide for torque math. |
| Pan and tilt head | Micro servos | Two-axis pointing with holding. The assembled kit below is built for this. |
For pan and tilt work, the mini pan-tilt camera kit is assembled with two SG90 micro servos and costs $20.99. The camera is not included. The pan tilt camera platform 2-pack costs $10.99, fits 9 g to 12 g SG90 and MG90S servos, and includes no camera and no servos. For a first arm build, the 4-DOF acrylic robot arm kit with claw starts at $18.00 for the Arm Only option in black (no servos) and $25.88 with four SG90 servos. The 5-DOF programmable robot arm kit costs $89.99 and the 6-DOF full metal robot arm kit costs $209.99 with six digital servos and a wireless handle. A build guide for an ESP32 servo arm is also on this site: How to Build a Robot Arm with ESP32 and Servo Motors.
Selection Checklist
- List each joint, its load, its lever arm, and its required range of motion.
- Size servo joints from listing torque at the voltage you will use, with 2x margin.
- Size stepper joints from torque at the speed you will run, not just standstill torque.
- Decide the homing plan for every stepper joint before you build.
- Check backlash needs: if reversing accuracy matters, test the actual gear train.
- Set stepper driver current limits for the motor, fit heatsinks, and check heat.
- Power servos separately from the controller, with a supply rated for stall current.
- Pick the controller: the ELEGOO UNO R3 at $21.99 for a full-size board with USB cable, or the Nano V3.0 at $8.49 for a compact build (no cable included, headers unsoldered, CH340G driver needed).
Compatibility and Limitations
Servo and stepper control are not interchangeable. Servos take a pulse signal on one pin each. Bipolar steppers like the NEMA 17 need a step and direction driver such as the A4988, TMC2208, or TMC2209. Unipolar steppers like the 28BYJ-48 need a ULN2003 board, which is included in the sets listed here. Do not drive a bipolar stepper from a ULN2003 board and do not drive a 5-wire unipolar stepper from an A4988. The wiring families are different, and the wrong pairing will not work.
Voltage matters on both sides. Servo torque ratings are voltage dependent. Stepper drivers have motor supply limits and logic supply limits. The A4988 listing states a motor supply up to 35V, and the Pololu page states a logic supply of 3V to 5.5V. The TMC2208 and TMC2209 listings state their own supply ranges, listed above. Exceeding a driver supply limit damages the driver. Running below the minimum gives weak or unreliable motion.
A small arm built from hobby parts has real limits. Hobby servos have gear backlash and limited life under repeated stalls. Small steppers lose torque at speed and miss steps under overload. Neither family gives industrial precision. For learning, prototyping, light pick and place, and camera pointing, both are excellent. For heavy loads or high precision, move to larger motors and drivers, and size the whole structure, not just the motor.
Browse the ranges in Stepper Motors and Drivers, Servos, Robot Arms, and Robotics.
Servo vs Stepper FAQ
Is a servo or a stepper better for a robot arm?
Both, in different joints. Servos suit gravity-loaded joints that need holding and simple control. Steppers suit continuous rotation and exact indexing. Most small arms use servos for the arm joints and steppers only where rotation or indexing is needed.
Do stepper motors hold position when powered off?
No, not reliably. Holding torque comes from energized coils. With power off, the detent torque is weak and a gravity-loaded joint can sag. Plan a park position or a brake if the load must stay put through a power loss.
Why does my stepper motor miss steps?
The usual causes are overload, too little current, too much speed for the load, or a supply that sags. Reduce speed, check the driver current limit, confirm the supply voltage and current, and reduce the load or add gear reduction.
Can I use a 28BYJ-48 stepper for a robot arm joint?
For slow, light joints, yes. The 1/64 gear train gives fine output steps and useful torque at low speed, but the motor is slow and has gear backlash. It suits pan motion and light indexing better than a fast, heavy shoulder joint.
Do I need a driver for a stepper motor?
Yes. A microcontroller pin cannot supply stepper coil current. Bipolar steppers need a step and direction driver such as the A4988. The 28BYJ-48 needs a ULN2003 board, which is included in the sets listed in this post.
Are TMC2208 and TMC2209 drivers quieter than A4988?
Yes, in normal use. Both TMC drivers list StealthChop2 quiet stepping. The A4988 is a solid basic driver and costs less per unit. The TMC2209 adds StallGuard4 sensorless homing. All three need correct current limits and cooling.
Sources
- TuteWorld: Servo vs Stepper
- ThinkRobotics: Stepper vs Servo Motor Robot Arm Guide
- Pololu: A4988 Stepper Motor Driver Carrier
- Texas Instruments: ULN2003A Product Details
- Arduino: UNO Rev3 Documentation
Shipped fast and securely from our secure facility in New York, providing fast, high quality USA shipping. Orders placed here ship fast from New York, USA.
