Robot Gripper Servo: Claw Torque, Travel, and Fit Checks
A robot gripper servo needs enough torque at the jaw lever arm, enough travel to open and close the jaws fully, and a horn and mount that fit your arm. Size torque from the load weight times the jaw distance, then add margin for friction and grip. Check travel, centering, and power before you mount anything. The sections below give the math, the checks, and the parts that fit.
All prices in this post are the effective prices checked November 18, 2026.
How a Robot Gripper Servo Works
A hobby servo is a geared motor with a built-in position control loop. You send it a pulse signal, and it drives its output shaft to the angle that matches the pulse width. The servo holds that angle against load until you send a new command. That holding behavior is what makes a servo the usual choice for a gripper: the jaws stay where you put them without constant attention from your code.
In a gripper, the servo output shaft carries a horn or disk. A linkage or a direct arm connects the horn to the moving jaw. As the servo rotates, the linkage pushes the jaw open or pulls it closed. Two things decide whether the gripper works: how much force the servo can apply at the jaw, and how far the jaw moves between fully open and fully closed. Both depend on geometry, not just on the servo. A longer horn gives more jaw travel but less force at the jaw. A shorter horn gives more force but less travel. You cannot get both from the same setup, so the design choice is a trade between grip force and jaw opening.
The Arduino Servo library is the standard way to drive these servos from a microcontroller. It provides attach() to connect a servo to a pin and write() to set a target angle. The library source is public on GitHub and is listed in the sources below. Before you trust any angle value in code, test the servo on the bench with the horn off, find the center, then mount the horn at the angle that gives equal travel both ways. That one check prevents most gripper failures.
Torque Math: Load, Lever Arm, and Margin
Servo torque is rated in kg-cm (kilogram-centimeters). The number means the servo can hold that many kilograms at a lever arm of 1 centimeter from the shaft center. Force at the jaw equals torque divided by lever arm. Double the lever arm and the force at the jaw drops by half. This is the only formula you need, and every gripper sizing mistake comes from skipping it.
Worked example 1. The MG90D digital metal gear micro servo is listed at 2.1 kg-cm of stall torque at 4.8V. With a jaw lever arm of 20 mm (2 cm), the force at the jaw is 2.1 divided by 2, which is about 1.05 kg of force equivalent. That is enough for light foam blocks and small plastic parts. It is not enough for a metal wrench.
Worked example 2. The DS3218MG 270 degree digital servo is listed at up to 21.5 kg-cm at 6.8V. With a 30 mm (3 cm) lever arm, the jaw force is 21.5 divided by 3, about 7.2 kg. With a 50 mm (5 cm) lever arm, the same servo gives 21.5 divided by 5, about 4.3 kg. The servo did not change. The geometry did.
Worked example 3. The DS3235 35KG coreless digital servo is listed at 29 kg-cm at 5V, 32 kg-cm at 6V, and 35 kg-cm at 7.4V. At 7.4V with a 40 mm (4 cm) lever arm, the jaw force is 35 divided by 4, about 8.75 kg. Note how the torque rating rises with supply voltage. If you run this servo at 5V, you get the 5V rating, not the headline rating. Always size from the rating at the voltage you will actually use.
Stall torque is the maximum the servo can hold at a standstill. Running a gripper near stall for long periods heats the motor and the driver inside the servo. Size for roughly twice the force you calculate, so the servo works in the middle of its range instead of at the edge. Friction in the linkage, jaw flex, and the grip surface all eat into the available force. A margin of 2x is cheap insurance. If your math says you need 3 kg at the jaw, pick a servo and geometry that gives 6 kg.
| Servo | Listing torque | Voltage for that rating | Size class | Price |
|---|---|---|---|---|
| MG90D micro servo | 2.1 kg-cm stall | 4.8V (2.4 kg-cm at 6.6V) | Micro, 13 g | $14.00 |
| MG92B micro servo | 3.5 kg-cm | 6.0V rating stated | Micro, 13.8 g | $17.00 |
| DS3218MG digital servo | Up to 21.5 kg-cm | 6.8V | Standard, 60 g | $23.99 |
| DS3235 coreless servo | 29 / 32 / 35 kg-cm | 5V / 6V / 7.4V | Standard | $48.99 |
| Micro servo SG90 / SG92R / MG90S | Not stated in listing | Not stated in listing | Micro, 9 g class | $13.99 to $19.99 by option |
| MG996R metal gear servo | Not stated in listing | Not stated in listing | Standard | $15.99 |
The last two rows are honest gaps. The listings for the micro servo options and the MG996R state gear type and size but give no torque, voltage, or speed figures. Do not size a gripper from a torque number you found on a random blog and assume it matches the unit you buy. If torque matters for your load, pick a servo whose listing states the torque at a stated voltage, or measure the servo you have before you build around it.
Travel: 180 Degree vs 270 Degree
Travel is how far the output shaft rotates from one end to the other. A 180 degree servo covers a half turn. A 270 degree servo covers three quarters of a turn. More travel means the horn sweeps a longer arc, which can open the jaws wider without a longer horn. That matters when the object you need to pick up is wider than the jaw opening your geometry allows.
The DS3218MG is listed as 270 degree controlled travel, with 360 degree rotation when powered off. That extra travel is useful for claws that need a wide open position and a firm closed position from one servo. The DS3235 is listed as a 180 degree version. Both work for grippers. The choice depends on your linkage: if your linkage needs more than a half turn of horn sweep to go from open to closed, you need the wider travel servo or a different linkage ratio.
Travel is not free. A servo that spreads its control signal range over 270 degrees has coarser angle steps than the same signal range spread over 180 degrees, and the ends of travel are where binding and stalling happen. Set software limits inside the mechanical limits. Drive the jaw to each end slowly on the bench, watch for the linkage hitting a hard stop, and back the limit off a few degrees. A servo stalled against a hard stop at full command will heat up and can strip gears or burn out. Limits in code are the cheapest protection you have.
Centering matters as much as travel. Mount the horn with the servo driven to its center position, not with the servo powered off. A horn mounted off center steals travel on one side and adds dead travel on the other. The jaw then fails to close fully or fails to open fully, and the fix is a horn remount, not new code.
Gears, Bearings, Horns, and Mounts
Gear material decides how much abuse the servo survives. The Micro Servo SG90 / SG92R / MG90S listing offers three options: the SG90 with plastic gears, the SG92R with carbon fiber gears, and the MG90S with metal gears. Plastic gears are fine for light, smooth loads. Metal gears survive stalls, impacts, and heavier jaws. For a gripper that will stall against objects, metal gears are the safer pick. The MG90S option and the SG92R option are both $13.99, and the SG90 option is $19.99, so the metal gear option costs no more than the carbon fiber option at the prices checked November 18, 2026.
Bearings matter when the jaw loads the shaft sideways. The MG90D and MG92B listings both state double ball bearings. A shaft supported by bearings stays aligned under side load. A shaft supported only by a bushing can tilt, bind, and wear the gear train. For a gripper with a long jaw, bearing support is worth having.
The horn or disk must match the servo spline. The metal servo disk 5-pack is 25T (25 tooth) and is stated as not for micro or mini servos. That disk fits standard-size servos. Micro servos use a smaller spline and their own horns. Check the spline before you order, and check that the disk diameter clears the mount and the linkage at full travel. A 20 mm disk that hits the bracket at the end of travel is a hard stop you did not plan.
Mounts hold the servo so the shaft stays put while the jaw works. The CNC aluminum servo mount bracket fits standard-size servos in the S3003, MG995, and MG996R class and costs $8.99. The servo is not included. For micro servos, the SG90 acrylic mount holder bracket 10-pack costs $12.87 and the servos are not included. A mount that flexes under load changes the jaw geometry as the load changes, which makes the grip unpredictable. Rigid mounts give repeatable grips.
Linkage hardware connects the horn to the jaw. The Control Linkage Hardware Kit costs $21.95. Keep linkages short and direct, use ball links or clevises that move freely without slop, and make sure nothing in the linkage binds at either end of travel. Slop in the linkage shows up as jaw play: the servo is in position but the jaw moves. That play is what drops objects.
Power the Gripper Servo Separately
Servos draw current spikes when they start moving and when they stall. The DS3235 listing states stall currents of 1.9A at 5V, 2.1A at 6V, and 2.3A at 7.4V. One stalled servo can pull more than a small regulator can deliver. If the servo shares a supply with the microcontroller, a current spike can brown out the controller and reset your program mid-grip. Power servos from their own supply or a dedicated regulator, and join the grounds.
A UBEC steps battery voltage down to a steady 5V for servos and receivers. The table below lists the three UBEC options verified in stock. Pick the current rating from your worst case: count the servos that can move at once, add their stall currents, and pick a UBEC rated above that total. A 3A UBEC is enough for one or two micro servos. A full arm with a gripper needs more.
| UBEC | Output | Input | Price |
|---|---|---|---|
| Switch Mode UBEC 3A | 5V at 3A | 2-6S LiPo | $10.99 |
| 5A Switch-Mode UBEC | 5V at 5A | 2-8S LiPo | $10.99 |
| 7A Switch-Mode UBEC | 5V at 7A | 2-8S LiPo | $12.99 |
For power planning detail, see the guide How to Choose a UBEC or BEC for Clean 5V Power in RC and How to Power an ESP32 Arduino Robot With a Battery and BEC. Both cover the same rule: size the supply for the stall case, not the idle case.
Control: Joystick, Code, and the Center Check
Two control styles cover most grippers. Manual control uses a joystick to open and close the jaw by hand. Programmed control sets jaw positions in code for pick and place routines. Many builders use both: joystick for testing, code for repeatable moves.
For manual control, the 4-axis joystick potentiometer gives X and Y tilt, Z twist, and a momentary top button, and costs $28.99. The twist axis is a natural fit for gripper open and close while the tilt axes drive the arm. The HiLetgo PS2 joystick sensor module is a smaller 2-axis module with a pushbutton for $10.99 and runs on 3.3V to 5V. For the controller, the ELEGOO UNO R3 board costs $21.99 and includes a USB cable.
Before first use, run the center check. Power the servo, drive it to center with a tester or a short sketch, then mount the horn. The Micro Servo Starter Kit includes a micro servo, an RC servo tester, and replacement arms for $32.95, which covers the center check without writing code. Test the full open and close range with no load, then with the lightest object you plan to grip, then with the heaviest. If the servo buzzes loudly at the closed position with no object in the jaw, the closed limit is driving into a hard stop. Back the limit off.
Fit Checklist Before You Mount Anything
- Torque math done at the voltage you will use, with 2x margin, using listing torque figures.
- Lever arm measured from the shaft center to the jaw contact point, not guessed.
- Travel checked: the servo reaches full open and full closed without the linkage hitting a hard stop.
- Horn mounted at center with the servo powered and driven to center.
- Spline match confirmed: 25T disks are for standard servos, not micro servos.
- Mount rigid, servo seated fully, screws snug but not crushing the case.
- Linkage free through the full range, no binding, minimal slop.
- Servo power separate from the controller supply, grounds joined, UBEC rated above worst-case stall current.
- Software limits set inside the mechanical limits at both ends.
- Bench test with no load, light load, and heavy load before the arm goes on the robot.
Compatibility and Limitations
Complete arm kits remove most fit questions. The 4-DOF acrylic robot arm kit with claw is unassembled acrylic with screws. The Arm Only option in black costs $18.00 and includes no servos. The With SG90 option in black costs $25.88 and adds four SG90 servos. Higher options add a UNO board and rocker controls, up to $86.99. Note that the wood finish options are acrylic with a wood-style film, not wood. The 5-DOF programmable robot arm kit costs $89.99, works with knob, PC, and Arduino IDE control, and needs two 18650 cells (not included) or Micro USB power. The 6-DOF full metal robot arm kit costs $209.99, uses six digital servos (five joints plus the gripper), includes a 7.5V 3A adapter, and has gear clutches at the gripper end.
Limitations to respect. A hobby servo gripper is a position device, not a force device. It cannot feel how hard it is gripping. Soft objects can be crushed and hard objects can slip if the jaw surface is smooth. Add grip pads for smooth objects and set a conservative closed limit for soft objects. A servo gripper cannot hold a load with the power off unless the gear train friction holds it, and you should not rely on that. If the load must stay gripped through a power loss, you need a different mechanism. Waterproof ratings on the DS3218MG and DS3235 listings describe the servo, not the arm, the linkage, or the electronics. Keep the rest of the build dry.
Browse the full ranges in Robot Arms, Servos, Servo Mounts, and Robotics.
Robot Gripper Servo FAQ
How much torque does a robot gripper servo need?
Divide the servo torque rating by the jaw lever arm in centimeters to get the force at the jaw, then size for about twice the force you need. A DS3218MG at 21.5 kg-cm with a 30 mm lever arm gives about 7.2 kg of jaw force. Always use the rating at the voltage you will run.
Is a 180 degree or 270 degree servo better for a gripper?
It depends on the linkage. A 270 degree servo sweeps a longer arc, which opens the jaws wider without a longer horn. A 180 degree servo is enough when the linkage ratio gives full open and close inside a half turn. Check the sweep on the bench before you decide.
Why does my gripper servo buzz and get hot?
The usual cause is a command that drives the jaw into a hard stop or holds a stall against a heavy load. Back the software limits off the mechanical ends, check that the linkage is not binding, and confirm the servo is sized with margin for the load. A separate servo supply also helps, since a shared supply can sag under stall current.
Can I use an SG90 for a robot gripper?
Yes, for light loads. The SG90 is a 9 g class micro servo with plastic gears. It suits small foam and plastic parts on a light arm. For heavier loads, repeated stalls, or long jaws, pick a metal gear micro servo or a standard-size servo with a stated torque rating.
Do I need a separate power supply for the gripper servo?
Yes, in most builds. Servo current spikes can reset a microcontroller that shares the same supply. Use a UBEC rated above the worst-case stall current of the servos that can move at once, and join the grounds between the servo supply and the controller.
How do I stop a gripper from crushing soft objects?
Set a conservative closed limit in code so the jaw stops before full force, add soft grip pads to spread the contact, and test with the actual objects. A hobby servo has no force feedback, so the limit and the pads are the control you have.
Sources
- RoboticsProjectHub: Servo Gripper
- Arduino Servo library source (GitHub)
- NZN Electronics: SG90 vs SG92R vs MG90S Micro Servo Guide
- ThinkingRobot: Servo Motor SG90 Arduino Guide
- BlueGrays: MG996R Servo Arduino Guide
- BlueGrays: Arduino Robotic Arm Guide
Shipped fast and securely from our secure facility in New York, providing fast, high quality USA shipping. Orders placed here ship fast from New York, USA.
