ESP32 SuperMini vs XIAO: Which Tiny Board Wins?

Pick the XIAO for battery builds, WiFi range, or a board that solders flat onto a carrier PCB. Pick the SuperMini for the lowest price per board, a breadboard-friendly header, or an on-board LED for blink and debugging.

The two families share the same chips, so the decision is about the board around the chip: the antenna, the battery circuit, the pins, the mounting, the documentation, and the price per board. Both run the same Arduino, MicroPython, and ESP-IDF code for the same chip once the pin names are changed: the XIAO uses D0 to D10 names and the SuperMini uses GPIO numbers.

How big is each board, and how does it mount?

Board Size Mounting
XIAO ESP32C3 21 x 17.8 mm (Seeed wiki) Castellated, solders flat onto a carrier PCB
ESP32-C3 SuperMini About 22.5 x 18 mm (seller listings only) Through-hole header pins, fits a breadboard
XIAO ESP32S3 21 x 17.8 mm (Seeed wiki) Castellated, solders flat onto a carrier PCB
ESP32-S3 SuperMini About 23.5 x 18 mm (espboards) Through-hole header pins, fits a breadboard

The XIAO is smaller by about a millimetre and a half in each direction, and its castellated edges let it solder flat onto a carrier board like a module. That suits a finished product, a wearable, or a sensor tag that has to sit flat inside a case.

The SuperMini is the breadboard board. Its through-hole header pins plug straight into a breadboard with room to spare, which is why it is the easier pick for a first build, a classroom set, or a prototype you plan to rewire. The trade off is height.

Measure your own SuperMini before you design a case around it. There is no single manufacturer, so pin labels, LED color, flash size, and antenna layout can vary between sellers and revisions.

Which board has more pins?

The SuperMini breaks out more pins on both chips. The XIAO keeps the same 11-pin header on every board: a feature when a sketch moves between XIAO boards, a limit when the build needs more pins.

XIAO C3 SuperMini C3 XIAO S3 SuperMini S3
Broken-out GPIO 11 (D0 to D10) 13 (GPIO0 to GPIO10, 20, 21) 11 (D0 to D10) 13 plus TX/RX
Analog header pins 4 (D0 to D3) 6 (GPIO0 to GPIO5) 9 (D0 to D5, D8 to D10) 13 (GPIO1 to GPIO13)

Sources: Seeed wiki pin maps; NuttX docs; TeachMeMicro.

Three pin differences matter. First, the XIAO bus pins never move: I2C is always D4 and D5, SPI is always D8, D9, and D10, and UART is always D6 and D7 on every XIAO board. The SuperMini has no such promise: the bus pins follow the chip, and the I2C pins on the C3 SuperMini sit on GPIO8 and GPIO9, which are also strapping pins, so the NuttX docs recommend GPIO0 and GPIO1 for I2C instead.

Second, the SuperMini gives you more analog pins: 6 ADC-capable pins on the C3 against 4 on the XIAO C3, and 13 on the S3 against 9 on the XIAO S3. The store listing states 4 analog pins for the C3 SuperMini against 6 in the NuttX table; the gap is the ADC2 channel on GPIO5, which reads unreliably while WiFi is running. Use GPIO0 to GPIO4 for analog reads when WiFi is on.

Third, strapping pins need care on both families, but on different pins. On the XIAO C3, D0, D8, and D9 decide the boot mode. On the C3 SuperMini, GPIO2, GPIO8, and GPIO9 do. On the XIAO S3, D2 (GPIO3) is the strapping pin on the header. On the S3 SuperMini, GPIO3 is the one to use with care. A sensor that pulls a strapping pin to the wrong level at reset can stop either board from booting. Full pin tables are in our SuperMini guide and our XIAO pinout guide.

How do the C3 boards compare?

The C3 comparison is the cleanest one, because the chips are identical. The ESP32-C3 datasheet v2.5 is the source for the chip figures.

Feature XIAO ESP32C3 ESP32-C3 SuperMini
Chip ESP32-C3, single-core RISC-V, up to 160 MHz Same chip
SRAM / flash 400 KB SRAM, 4 MB flash Same
Deep sleep, board level 44 uA per the Seeed wiki No board-level figure published for the generic board
QRC price $13.99 for one board $22.99 for four boards ($5.75 per board)

Sources: Espressif C3 datasheet v2.5; Seeed wiki C3 page; Mischianti; NuttX docs.

The C3 decision comes down to two questions. Does the build run on a battery? The XIAO charges a LiPo over USB with no extra parts, and its 44 uA board-level deep sleep figure is published by Seeed. The SuperMini usually has no charging circuit, and no board-level figure is published for the generic board. The bare C3 chip can sleep near 5 uA, but a finished board draws more.

Does the build need WiFi range? The XIAO needs its external antenna connected, and with it fitted Seeed states over 100 m line of sight. The SuperMini ceramic antenna needs nothing fitted and works well at short range, but range varies by batch. One user test on the Seeed forum measured the SuperMini at -33 dBm next to a phone against about -60 dBm for a XIAO with no antenna fitted: with its antenna fitted, the XIAO is the stronger board.

How do the S3 boards compare?

The S3 comparison is where the memory gap shows up, and it is the biggest spec difference between the two families.

Feature XIAO ESP32S3 ESP32-S3 SuperMini
Chip ESP32-S3R8, dual-core Xtensa LX7, up to 240 MHz ESP32-S3, dual-core Xtensa LX7, up to 240 MHz
PSRAM / flash 8 MB PSRAM, 8 MB flash 4 MB flash, 2 MB PSRAM on the common FH4R2 version
Deep sleep, board level 14 uA per the Seeed wiki About 43 uA per the store listing
User LED User LED on GPIO21, plus charge LED RGB LED, typically WS2812 on GPIO48
QRC price $21.49 for one board $31.99 for five boards ($6.40 per board)

Sources: Seeed wiki S3 page; Espressif S3 datasheets; TeachMeMicro; Lingflux.

The memory gap is the whole S3 story. The XIAO ESP32S3 carries the S3R8 chip with 8 MB of PSRAM and 8 MB of flash. The common S3 SuperMini carries the S3FH4R2 chip with 4 MB of flash and 2 MB of PSRAM: four times the PSRAM and twice the flash on the XIAO. PSRAM holds camera frames, display buffers, and audio at runtime, so the XIAO S3 is the board for camera work, displays, and edge AI. The SuperMini S3 still handles bigger sketches, more sensors, and small displays, but with less headroom.

Check the chip marking on any S3 SuperMini before you trust a memory figure: FH4R2 means 4 MB of flash and 2 MB of PSRAM. Run the memory check sketch in our SuperMini guide to confirm flash size and PSRAM before you write code that needs them.

The S3 boards are closer on the other rows: both have a user LED, USB OTG, and battery charging in some form. The XIAO S3 still wins on range, deep sleep, and documentation; the SuperMini S3 on price per board and breadboard use. The Sense version is the XIAO-only option, adding a detachable camera, a digital microphone, and a microSD slot on an expansion board. There is no SuperMini equivalent. Camera projects are covered in our XIAO S3 Sense guide.

Which board is better on battery power?

The XIAO is the better battery board on both chips. Every XIAO has a built-in LiPo charging circuit with BAT pads on the back: plug a LiPo in and the board charges it over USB, with no extra module. The Seeed wiki publishes board-level deep sleep figures of 44 uA for the C3 and 14 uA for the S3, and the XIAO C3 has no user LED at all, so nothing drains the cell in deep sleep. The C3 SuperMini usually has no charging circuit, so a battery build needs an external charging module, and no board-level deep sleep figure is published for the generic board. The S3 SuperMini is better here: some S3 boards have battery pads with a charger, and the listing states deep sleep around 43 uA.

One safety note: the XIAO C3 charging circuit delivers a fast charge near 370 mA, so use a battery of 370 mAh or larger unless the battery has its own protection circuit. Source: Mischianti XIAO ESP32-C3 guide.

How much does each board cost?

Prices below are the live QRC store prices. The SuperMini boards sell as packs, so the per-board price is arithmetic from the pack price.

Board QRC listing Pack price Price per board
XIAO ESP32C3, 1-pack ID 17820 $13.99 $13.99
ESP32-C3 SuperMini, 4-pack ID 19646 $22.99 $5.75
XIAO ESP32S3, 1-pack ID 17839 $21.49 $21.49
ESP32-S3 SuperMini, 5-pack ID 19649 $31.99 $6.40

The SuperMini is far cheaper per board: about $5.75 against $13.99 on the C3, and about $6.40 against $21.49 on the S3. A four-pack of C3 SuperMinis costs less than two single XIAO C3 boards, and a five-pack of S3 SuperMinis costs about one and a half XIAO S3 boards.

Prices were verified against the live SuperMini guide (updated 2026-11-21) and the batch 2 verification of the same day. The public Store API returned HTTP 429 at draft time, so re-verify every price live before publishing.

Which one should you buy?

Pick by the build, not by the brand.

Buy the XIAO ESP32C3 if the build is a battery sensor, a wearable, a BLE beacon, or a node that has to sit in another room and stay connected. The charging circuit, the external antenna, and the 44 uA deep sleep are the reasons.

Buy the ESP32-C3 SuperMini if the build is a set of cheap sensor nodes, a classroom set, or a first ESP32 project, or anything where the lowest cost per board matters most. At $5.75 per board in the 4-pack, it is the cheapest way to put WiFi and Bluetooth on a tiny board, and the blue LED makes Blink work out of the box.

Buy the XIAO ESP32S3 if the build needs memory: camera work, a display with a frame buffer, audio, edge AI, or a large sketch. The 8 MB of PSRAM and 8 MB of flash are the reasons. Buy the Sense version instead for a camera, a microphone, and a microSD slot.

Buy the ESP32-S3 SuperMini if the build needs two cores, more pins, and some PSRAM, but does not need 8 MB of it: bigger sensor builds, small displays, and multi-node projects where $6.40 per board beats $21.49. Check the chip marking for FH4R2 before relying on the PSRAM figure.

If you are still unsure, buy the C3 SuperMini 4-pack first. It is the cheapest way to learn the setup, and the steps transfer to the other boards.

What are the common mistakes?

  • Running a XIAO with no antenna. The XIAO has no built-in antenna. WiFi and Bluetooth will barely work until the included external antenna is fitted to the U.FL connector.
  • Using a SuperMini pinout on a XIAO, or the reverse. D4 is GPIO6 on the XIAO C3 and GPIO4 on the C3 SuperMini. Use the pin table for your exact board.
  • Expecting Blink to work on the XIAO C3. There is no user LED on the XIAO C3, only a charge LED. Wire an external LED before you run Blink.
  • Assuming the S3 SuperMini has 8 MB of PSRAM. The common FH4R2 version has 2 MB of PSRAM and 4 MB of flash. Check the chip marking.
  • Comparing a chip deep sleep figure against a board deep sleep figure. The bare C3 chip can sleep near 5 uA, but a finished board draws more through its regulator, LEDs, and USB circuitry. Seeed publishes board-level figures for the XIAO (44 uA C3, 14 uA S3). No equivalent figure is published for the generic SuperMini.

How do I troubleshoot a SuperMini vs XIAO problem?

The board does not appear as a USB port. Try a USB-C data cable, not a charge-only cable. Then hold BOOT, connect the cable, release BOOT, and upload Blink. Full steps are in our SuperMini guide.

The Serial Monitor is blank but the sketch runs. Set USB CDC On Boot to Enabled under Tools and re-upload. Full steps are in our SuperMini guide.

WiFi will not connect on a XIAO. Check the antenna first. If the external antenna is not fitted, fit it and test again. If it is fitted, check the connector is fully seated.

WiFi will not connect on a SuperMini. Move the board closer to the router first. Some batches have weak WiFi that improves when the transmit power is lowered in code.

Parts used in this guide

Prices and stock were verified against the live SuperMini guide (updated 2026-11-21) and the batch 2 verification of the same day. The public Store API returned HTTP 429 at draft time. Re-verify every price and stock live before publishing.

Shipped fast and securely from our secure facility in Queensbury, NY. QRC ships within the USA only.

Related guides

FAQ

What is the difference between an ESP32 SuperMini and a XIAO ESP32? Same chip, different board. The XIAO has an external U.FL antenna, a built-in LiPo charging circuit, and no user LED on the C3. The SuperMini has a ceramic antenna, usually no charging circuit, and a blue LED typically on GPIO8. Pick the XIAO for battery sensors and range, the SuperMini for the lowest cost and breadboard work. Source: Mischianti; our SuperMini guide FAQ.

Can I use the same code on a SuperMini and a XIAO? Yes, with the pin names changed. Both run the same Arduino, MicroPython, and ESP-IDF code for the same chip. The XIAO uses D0 to D10 names and the SuperMini uses GPIO numbers. Source: The Engineering Projects XIAO ESP32-C3 guide.

Which board is better for battery projects? The XIAO, on both chips. It charges a LiPo over USB with no extra parts, and Seeed publishes board-level deep sleep figures of 44 uA for the C3 and 14 uA for the S3. The C3 SuperMini usually has no charging circuit and no published deep sleep figure. Source: Seeed wiki C3 and S3 pages; Mischianti XIAO ESP32-C3 guide.

Does the XIAO need an external antenna? Yes. The XIAO has a U.FL connector only and no built-in antenna. The antenna ships in the box and must be fitted before WiFi or Bluetooth will work properly. Source: Seeed wiki S3 page; Seeed forum BLE signal thread.

Which S3 board should I buy, the SuperMini or the XIAO S3? Buy the XIAO S3 if the build needs memory: camera work, displays, audio, or large sketches. It has 8 MB of PSRAM and 8 MB of flash against 2 MB of PSRAM and 4 MB of flash on the common S3 SuperMini FH4R2 version. Buy the S3 SuperMini for two cores, more pins, and some PSRAM at $6.40 per board in the 5-pack. Check the chip marking for FH4R2 before trusting the memory figure. Source: Seeed wiki S3 page; TeachMeMicro; Lingflux.

Sources

Last updated: 2026-11-21

Change log

  • 2026-11-21: Draft created. Direct SuperMini vs XIAO comparison across the C3 and the S3: size, pins, antenna, battery, memory, and price per board. Overlap checked against live posts 15176 (SuperMini guide, one C3-only comparison section) and 18592 (XIAO four-board comparison, no SuperMini coverage). Batch 2 XIAO pinout draft not live yet at draft time, so no link to it is included. Product prices carried from the live SuperMini guide (updated 2026-11-21) and batch 2 verification of the same day; the public Store API returned HTTP 429 at draft time, so prices and stock must be re-verified live before publishing, and the slug 404 must be re-checked at publish time for the same reason.
  • 2026-11-21: Trimmed from 3,492 to 2,797 publishable words (H1 through FAQ, plain wc -w; 2,969 H1 through Last updated, Sources included). Cut one FAQ, shortened table cells and Sources lines, and trimmed prose across size, pins, C3, S3, battery, price, buy, mistakes, troubleshooting, and parts sections. No facts, prices, or safety notes changed.