Last updated: 2026-11-22
Last updated: 2026-11-22
If you are asking which ESP32 should I buy, start here: buy an ESP32-S3 board. The ESP32-S3 Development Board DevKitC-1 gives dual-core processing at 240 MHz, WiFi, Bluetooth LE, native USB, and enough memory for almost every hobby project. Pick a different chip only for one clear need: Bluetooth audio, a 5 GHz network, a Thread or Matter device, a battery node that must sleep for months, or a large touchscreen.
This guide compares every ESP32 chip Espressif sells, then matches a chip to nine project types: WiFi sensor, camera, battery device, display, robotics, RC, Bluetooth audio, Thread and Matter, and USB HID. Pick the chip first. The board only breaks out the chip pins and adds a USB bridge, a regulator, and buttons.
Table of contents
- Which ESP32 should you buy first?
- How do the ESP32 chips compare?
- What does each chip name mean?
- Which ESP32 is best for a WiFi sensor?
- Which ESP32 is best for a camera?
- Which ESP32 is best for a battery-powered device?
- Which ESP32 is best for a display?
- Which ESP32 is best for robotics?
- Which ESP32 is best for RC and drones?
- Which ESP32 is best for Bluetooth audio?
- Which ESP32 is best for Thread, Zigbee, and Matter?
- Which ESP32 is best for USB HID?
- What about the ESP32-P4?
- What about the ESP32-S31?
- What about the ESP8266?
- Which board, not just which chip?
- Best for and not for: every chip
- What mistakes do first-time buyers make?
- How do you check a new board works?
- Frequently asked questions
- Parts used in this guide
- In this series
- Related guides
- Sources
Which ESP32 should you buy first?
The short answer to which ESP32 should I buy is the ESP32-S3. It is the default pick for 2026 because it covers the most project types: dual-core 240 MHz processing, WiFi, Bluetooth LE 5.0, native USB OTG, a camera interface, and PSRAM options up to 16 MB in the package. It runs Arduino, MicroPython, and ESP-IDF, and most current tutorials target it. Buy the classic ESP32 DevKit V1 instead if you are following an older tutorial word for word: it has the largest pile of existing tutorials and is the only ESP32 chip with Bluetooth Classic. Buy an ESP32-C3 board instead if the node must be tiny, cheap, and low power with only WiFi and Bluetooth LE. Buy an ESP32-C6 board instead if the project joins a Thread, Zigbee, or Matter network.
How do the ESP32 chips compare?
Use this table to pick the chip. GPIO counts are chip totals. A real board breaks out fewer pins, so check the board pinout before you order.
| Chip | Cores | Max clock (MHz) | Wi-Fi | Bluetooth | 802.15.4 | USB | PSRAM options | GPIO on chip |
|---|---|---|---|---|---|---|---|---|
| ESP32 | 2x Xtensa LX6 | 240 | Wi-Fi 4, 2.4 GHz | Classic + BLE 4.2 | No | USB-serial bridge on board, none on chip | WROOM none; WROVER 4 or 8 MB | 34 |
| ESP32-S2 | 1x Xtensa LX7 | 240 | Wi-Fi 4, 2.4 GHz | None | No | USB OTG full speed | In-package up to 2 MB; external supported | 43 |
| ESP32-S3 | 2x Xtensa LX7 | 240 | Wi-Fi 4, 2.4 GHz | BLE 5.0 | No | USB OTG full speed + USB Serial/JTAG | In-package up to 16 MB; external up to 32 MB | 45 |
| ESP32-C2 | 1x RISC-V | 120 | Wi-Fi 4, 2.4 GHz | BLE 5.0 | No | USB Serial/JTAG only | External up to 8 MB; none in package | 14 |
| ESP32-C3 | 1x RISC-V | 160 | Wi-Fi 4, 2.4 GHz | BLE 5.0 | No | USB Serial/JTAG only | External up to 8 MB; none in package | 22 |
| ESP32-C5 | 1x HP RISC-V + 1x LP RISC-V | 240 | Wi-Fi 6, 2.4 + 5 GHz | BLE, Bluetooth Core 6.0 certified | Yes, Thread 1.4 + Zigbee 3.0 | USB Serial/JTAG only | In-package 2 or 8 MB by variant; external up to 32 MB | 29 |
| ESP32-C6 | 1x RISC-V + 1x LP RISC-V | 160 | Wi-Fi 6, 2.4 GHz | BLE 5.3 | Yes, Thread + Zigbee | USB Serial/JTAG only | External up to 16 MB; none in package | 30 |
| ESP32-H2 | 1x RISC-V | 96 | None | BLE 5.3 | Yes, Thread + Zigbee | USB Serial/JTAG only | External up to 16 MB; none in package | 19 |
| ESP32-P4 | 2x RISC-V + 1x LP RISC-V | 400 | None, needs a companion chip | None, needs a companion chip | No | USB 2.0 high speed OTG + full speed OTG + USB Serial/JTAG | In-package 16 or 32 MB | 55 |
| ESP32-S31 | 2x RISC-V + 1x LP RISC-V | 320 | Wi-Fi 6, 2.4 GHz | BLE 5.4 + Classic | Yes, Thread 1.4 + Zigbee 3.0 | USB OTG high speed | In-package 8, 16, or 32 MB | 60 |
On-chip SRAM, per Espressif published data: classic ESP32 520 KB, S2 320 KB, S3 512 KB, C2 272 KB, C3 400 KB, C5 384 KB plus 16 KB low-power SRAM, C6 512 KB, H2 320 KB, P4 768 KB, S31 512 KB. A camera frame, display buffer, or audio buffer that does not fit in SRAM needs PSRAM, and only the S3, C5, P4, and S31 offer it in the package in useful sizes.
Two warnings: the ESP32-P4 has no radio at all, so a P4 board needs a companion chip for WiFi and Bluetooth. The ESP32-S31 datasheet is pre-release v0.6 and the chip was sampling for select customers at last check, so treat the ESP32-S31 as a chip to watch, not a board to buy today.
What does each chip name mean?
The letter after ESP32 names the chip line. S means a high-performance Xtensa chip with USB and, on the ESP32-S3, AI vector instructions. C means a low-cost RISC-V chip. H means a low-power 802.15.4 chip with no WiFi. P means a high-performance RISC-V chip built for screens and video, with no radio. The number is the generation inside the line: the ESP32-S3 is the newer S chip, the ESP32-C6 is the newer C chip with WiFi 6 and 802.15.4, and the ESP32-C5 is the C chip that adds 5 GHz WiFi. Espressif is moving from Xtensa cores to RISC-V cores: the classic ESP32, ESP32-S2, and ESP32-S3 use Xtensa, and every newer chip uses RISC-V. The change does not change how you write Arduino code, because the Arduino-ESP32 core and ESP-IDF support both core types.
Which ESP32 is best for a WiFi sensor?
For a WiFi sensor, the ESP32-C3 is the pick when you ask which ESP32 should I buy. A single RISC-V core at up to 160 MHz reads a sensor and sends the result over WiFi or Bluetooth LE, and the ESP32-C3 runs the lowest deep sleep current in the WiFi group at around 5 uA. Pick the ESP32-C3 SuperMini or the Seeed XIAO ESP32C3 when the node must be small; both carry native USB, so no adapter is needed. Pick the ESP32-C6 for WiFi 6 or a path to Thread, and the classic ESP32 DevKit V1 for an older tutorial. Do not pick the ESP32-S3 for a plain sensor node: it works, but it costs more space and sleep current than the job needs.
Which ESP32 is best for a camera?
The ESP32-S3 is the best pick for a camera. The ESP32-S3-CAM board pairs the ESP32-S3-WROOM-1 N16R8 module, with 16 MB flash and 8 MB PSRAM, with a camera connector, dual USB-C ports, and a TF card slot. The PSRAM holds larger frames, and the ESP32-S3 vector instructions speed up small on-board vision work such as face detection. Compare the two camera boards in ESP32-CAM vs ESP32-S3-CAM: Which Camera Board to Pick, and set the S3 board up with How to Use the ESP32-S3-CAM Board for Camera Projects. Pick the classic ESP32-CAM instead for a simple WiFi camera: a live stream, photos to microSD, and motion alerts, with 4 MB of PSRAM and an OV2640 camera. Do not pick the ESP32-C3 or ESP32-C6 for a camera: neither chip has a camera interface or PSRAM in the package.
Which ESP32 is best for a battery-powered device?
The ESP32-C3 is the best pick for a battery-powered WiFi device, and the ESP32-H2 is the best pick for a battery-powered Thread or Zigbee device. The ESP32-C3 deep sleep current sits around 5 uA, the lowest of the WiFi chips. The ESP32-H2 sits around 7 uA with no WiFi radio to feed. The ESP32-C6 also sits around 7 uA and keeps WiFi 6 plus 802.15.4, so it is the pick when a battery node must talk WiFi today and Thread later. Battery life depends on the board as much as the chip: a board with a power LED, a USB-serial chip, and a linear regulator draws far more than the chip deep sleep figure. Measure the whole board in deep sleep, and read How to Power ESP32 and Arduino Projects on LiPo Power for charging, protection, regulation, and run-time math. Do not pick the ESP32-P4 for a battery device: it is the most power-hungry chip in the family.
Which ESP32 is best for a display?
The ESP32-S3 is the best pick for a display. With PSRAM it drives SPI TFT and OLED displays, holds the frame buffer in memory, and its USB OTG port supports touch input. The 1.9 inch TFT board and the 0.96 inch OLED board are compared pin for pin in ESP32 Boards with Built-In Displays: TFT vs OLED Compared. Pick the ESP32-P4 instead for a large MIPI panel: it drives MIPI-DSI displays up to 1080p, takes MIPI-CSI camera input, and encodes H.264 video in hardware. It has no WiFi or Bluetooth, so a P4 board pairs with a companion chip such as the ESP32-C6 for wireless. Do not pick the ESP32-C3 for a display larger than a small OLED: it has no PSRAM in the package and only 22 GPIO pins on the chip.
Which ESP32 is best for robotics?
The ESP32 DevKit V1 is the best pick for a first robot, and the ESP32-S3 is the best pick for a robot that also needs a camera, a display, or USB. The DevKit V1 gives dual-core 240 MHz processing, WiFi, Bluetooth, 30 pins, and 4 MB of flash on a board that fits a breadboard. The ESP32-S3 adds native USB, more memory, and a camera interface for a vision robot. The robot-by-robot picks, with wiring and power, are in How to Choose ESP32 Boards for Your Robotics Projects. One rule applies to every ESP32 robot: no board pin can power a servo or a motor directly. Every ESP32 runs on 3.3 V logic, so a 5 V sensor needs a level shifter, and servos and motors need their own power supply with a shared ground.
Which ESP32 is best for RC and drones?
The ESP32-C3 SuperMini and the ESP32-S3 SuperMini are the best picks for RC and drones, because size and weight decide the fit. The C3 SuperMini fits tight frames and runs WiFi telemetry, while the S3 SuperMini adds dual-core power and more pins for a flight controller companion or a camera. The ESP32-S2 Mini is the pick for WiFi and USB in a small board without Bluetooth. Drone fitting detail is in How to Choose ESP32 Boards for Drones and FPV Projects, and tiny-board pinouts are in How to Pick an ESP32 SuperMini Board for Tiny Builds. Do not pick the classic ESP32 DevKit V1 for a small drone frame: it is wider than a standard breadboard. Do not pick the ESP32-CAM for a drone that needs pins: the camera and the SD card take most of the free GPIO pins.
Which ESP32 is best for Bluetooth audio?
The classic ESP32 is the only pick for Bluetooth audio. It is the only ESP32 chip with Bluetooth Classic, which is what A2DP audio streaming and the Serial Port Profile (SPP) need. Every newer chip, including the ESP32-S3, ESP32-C3, ESP32-C5, and ESP32-C6, is Bluetooth LE only. Bluetooth LE does not carry A2DP audio, so a Bluetooth speaker or audio receiver must use the classic ESP32. For Bluetooth LE work such as beacons, phone apps, and BLE sensors, any chip with BLE 5 works. The ESP32-S3 is the usual pick, and the ESP32-C3 is the pick when the BLE node must be small and low power.
Which ESP32 is best for Thread, Zigbee, and Matter?
The ESP32-C6 is the best pick for Thread, Zigbee, and Matter. It combines Wi-Fi 6 at 2.4 GHz with an 802.15.4 radio for Thread and Zigbee on one chip, plus Bluetooth LE 5.3, and it supports Matter over Thread and Matter over WiFi. It also carries a low-power RISC-V core that runs while the main core sleeps. Pick the ESP32-H2 instead for a battery-powered Thread or Zigbee end device: same 802.15.4 radio and Bluetooth LE 5.3, no WiFi radio, and the lowest power draw of the two. Pick the ESP32-C5 instead when the Matter device also needs 5 GHz WiFi: it is the only ESP32 chip with dual-band Wi-Fi 6 at 2.4 and 5 GHz, plus 802.15.4. The XIAO family comparison is in XIAO ESP32C3 vs C6 vs S3 vs C5: Pick the Right Board.
Which ESP32 is best for USB HID?
The ESP32-S3 is the best pick for USB HID. It has native USB OTG, so the chip itself can act as a USB keyboard, mouse, MIDI device, or flash drive, with no separate USB chip. The ESP32-S2 also has USB OTG and is the lower-cost pick when the HID device needs WiFi and USB but no Bluetooth. The ESP32-C3, ESP32-C6, ESP32-H2, and ESP32-C5 have USB Serial/JTAG only, a programming and debug port, not a USB device port, so they cannot act as a USB keyboard or mouse. The classic ESP32 has no USB on the chip at all. For USB HID, the choice is the ESP32-S3 first and the ESP32-S2 second.
What about the ESP32-P4?
The ESP32-P4 is a high-performance microcontroller for screens, cameras, and video, not a general ESP32 board. Per the Espressif ESP32-P4 datasheet, it carries a dual-core RISC-V processor at up to 400 MHz, a low-power RISC-V core at up to 40 MHz, 768 KB of SRAM, 16 or 32 MB of PSRAM in the package, 55 GPIO pins, MIPI-CSI camera input, MIPI-DSI display output, an image signal processor, a JPEG codec, and a hardware H.264 encoder, plus USB 2.0 high-speed OTG at 480 Mbps and 10/100 Ethernet. The ESP32-P4 has no WiFi, Bluetooth, or 802.15.4 radio. A P4 board adds wireless with a companion chip, usually the ESP32-C6, over SDIO or SPI. Buy an ESP32-P4 board only for a large touchscreen, a MIPI camera, or hardware video encoding. For every other project, the ESP32-S3 costs less and already has WiFi and Bluetooth on the chip.
What about the ESP32-S31?
The ESP32-S31 is Espressif's newest multi-protocol chip, and it is a chip to watch rather than a board to buy today. Per the Espressif ESP32-S31 product page, it carries a dual-core 32-bit RISC-V processor at up to 320 MHz with a 128-bit SIMD data path, 512 KB of SRAM, 60 GPIO pins, 2.4 GHz Wi-Fi 6, Bluetooth 5.4 with LE and Classic, IEEE 802.15.4 for Thread and Zigbee, a Gigabit Ethernet MAC, USB OTG high speed, and 8, 16, or 32 MB of PSRAM in the package. The ESP32-S31 Series Datasheet is pre-release v0.6, and Espressif described the chip as sampling for select customers when it was announced, so finished boards are scarce and the Arduino and ESP-IDF support is still new, with ESP-IDF v6.1 as the listed target. If you need a board this week, buy the ESP32-S3 or the ESP32-C6 instead.
What about the ESP8266?
The ESP8266 is the predecessor chip, not an ESP32. It gives single-band WiFi on a single core with far fewer pins and no Bluetooth. It still fits one job: a simple WiFi sensor or switch where the board is already in hand and the sketch already works. For a new purchase, the ESP32-C3 costs about the same, adds Bluetooth LE and native USB, and runs the same Arduino code with more pins and more memory. If you already own a NodeMCU ESP8266 board, the setup and OLED guide is in How to Use NodeMCU ESP8266 with a Built-In OLED Display. If you are choosing between Arduino, ESP32, and RP2040, read Arduino vs ESP32 vs RP2040: Which Dev Board for Your Robot first.
Which board, not just which chip?
Once you know which ESP32 should I buy for the chip, pick the board that breaks out the pins you need. The same chip ships on many boards, and the board decides the USB connector, the regulator, the antenna, and the pins you can reach.
| Chip | Board pick | Notes |
|---|---|---|
| ESP32 | ESP32 DevKit V1, 30-pin, ESP32-WROOM-32 | Most tutorials use it |
| ESP32-S3 | ESP32-S3 DevKitC-1, 44-pin, USB-C | N16R8 module, 16 MB flash, 8 MB PSRAM |
| ESP32-S2 | ESP32-S2 Mini, USB-C | 4 MB flash, 2 MB PSRAM, no Bluetooth |
| ESP32-C3 | ESP32-C3 SuperMini or Seeed XIAO ESP32C3 | Thumb-sized, native USB-C |
| ESP32-C6 | ESP32-C6 SuperMini or Seeed XIAO ESP32C6 | Wi-Fi 6 and 802.15.4, small board |
| ESP32-C5 | Seeed XIAO ESP32-C5 | Dual-band Wi-Fi 6 and Matter |
| ESP32-H2 | ESP32-H2 SuperMini | Thread and Zigbee end devices |
| ESP32-CAM | ESP32-CAM with ESP32-CAM-MB carrier | Carrier adds Micro USB for programming |
| ESP32-S3-CAM | ESP32-S3-CAM board | Dual USB-C, programs directly |
Check the board pinout before you order: a 30-pin ESP32 DevKit V1, a 38-pin ESP32-DevKitC, and a 44-pin ESP32-S3 DevKitC-1 do not share a pin layout. The XIAO ESP32S3 and its Sense expansion board are covered in Seeed XIAO ESP32S3 Guide: Standard Board vs Sense Board.
Best for and not for: every chip
These Best for lines are the short answer to which ESP32 should I buy for each chip. Read the project sections above for the reasons.
- ESP32: Best for older tutorials and Bluetooth Classic audio. Not for Thread, Matter, USB HID, or PSRAM cameras.
- ESP32-S2: Best for WiFi and USB devices without Bluetooth, such as a USB HID gadget. Not for Bluetooth, Thread, or a camera.
- ESP32-S3: Best for most buyers, cameras, displays, USB HID, and edge AI. Not for Bluetooth Classic audio, Thread, Matter, or 5 GHz WiFi.
- ESP32-C2: Best for the lowest-cost simple WiFi node with Bluetooth LE. Not for many pins, PSRAM, or USB OTG.
- ESP32-C3: Best for tiny low-power WiFi and BLE sensor nodes and battery devices. Not for cameras, large displays, Thread, or USB HID.
- ESP32-C5: Best for dual-band Wi-Fi 6 with 5 GHz, plus Thread and Matter. Not for USB HID, a camera interface, or the lowest deep sleep current.
- ESP32-C6: Best for Thread, Zigbee, and Matter devices, and Wi-Fi 6 sensor nodes. Not for cameras, USB HID, or Bluetooth Classic audio.
- ESP32-H2: Best for battery-powered Thread and Zigbee end devices with Bluetooth LE. Not for WiFi, cameras, displays, or USB HID.
- ESP32-P4: Best for large MIPI touchscreens, MIPI cameras, and hardware video encoding. Not for WiFi or Bluetooth without a companion chip, and not for battery power.
- ESP32-S31: Best for watching: WiFi 6, Bluetooth Classic and LE, 802.15.4, Ethernet, and 60 GPIO pins on one chip, once boards ship. Not for buying today: the datasheet is pre-release and the chip was sampling at last check.
What mistakes do first-time buyers make?
First, buying for the chip name instead of the project need. A buyer who needs Thread and buys an ESP32-S3 has bought the wrong chip, because the ESP32-S3 has no 802.15.4 radio. Write down the one radio the project needs before you order. Second, buying a camera board without PSRAM. A camera frame needs memory, and a board without PSRAM holds only small frames. The ESP32-CAM carries 4 MB of PSRAM, and the ESP32-S3-CAM board carries 8 MB. Third, trusting the chip GPIO count instead of the board pinout. The ESP32-S3 chip has 45 GPIO pins, but a board breaks out fewer, and some pins are strapping, flash, or USB pins. Check the board pinout, not the chip datasheet alone. Fourth, assuming every ESP32 board has Bluetooth. The ESP32-S2 has no Bluetooth at all. The ESP32-H2 has no WiFi at all. Read the radio row in the comparison table before you order. Fifth, buying a board with no USB port for programming. The bare ESP32-CAM board has no USB port and needs the ESP32-CAM-MB carrier or an FTDI adapter. The ESP32-S3-CAM board programs directly over dual USB-C ports.
How do you check a new board works?
Run a WiFi scan sketch after the board arrives. The sketch below uses the Arduino-ESP32 core and the built-in WiFi library, so no extra library is needed. It lists the networks the board can see, which proves the radio, the antenna, and the USB connection in one step. Load it in Arduino IDE, open the Serial Monitor at 115200 baud, and check that network names appear.
// Board check: WiFi scan. Arduino-ESP32 core, built-in WiFi library.
// No extra libraries needed. Compiled 2026-11-22 with PlatformIO 6.2.0 (espressif32, esp32dev).
#include <WiFi.h>
void setup() {
Serial.begin(115200);
delay(1000);
WiFi.mode(WIFI_STA); // Station mode: the board joins networks.
WiFi.disconnect(); // Clear any saved network before scanning.
delay(100);
Serial.println("Scanning for WiFi networks...");
int networks = WiFi.scanNetworks();
Serial.print("Networks found: ");
Serial.println(networks);
for (int i = 0; i < networks; i++) {
Serial.print(i + 1);
Serial.print(": ");
Serial.print(WiFi.SSID(i)); // Network name.
Serial.print(" (");
Serial.print(WiFi.RSSI(i)); // Signal strength in dBm.
Serial.println(" dBm)");
}
}
void loop() {
// Nothing to repeat. Run the scan once per reset.
}
If the scan finds no networks, check the antenna first: some boards ship with a PCB antenna and some with a U.FL connector that needs an antenna fitted. Then check the board selection in Arduino IDE, then the USB cable, because a charge-only cable carries power but no data. The full USB detection fixes are in post 10 in this series.
Frequently asked questions
Which ESP32 should I buy as a beginner?
The ESP32-S3 is the best ESP32 for beginners starting fresh, because it covers WiFi, Bluetooth LE, USB, cameras, and displays on one board. The classic ESP32 DevKit V1 is the best ESP32 for beginners following an older tutorial, because most older tutorials name the classic ESP32 pins. Either board runs the Arduino-ESP32 core.
What is the difference between ESP32 and ESP32-S3?
The ESP32 is the classic dual-core Xtensa LX6 chip at 240 MHz with Wi-Fi 4, Bluetooth Classic and BLE 4.2, and 34 GPIO pins. The ESP32-S3 is the newer dual-core Xtensa LX7 chip at 240 MHz with Wi-Fi 4, Bluetooth LE 5.0, native USB OTG, a camera interface, AI vector instructions, and 45 GPIO pins. The ESP32-S3 has no Bluetooth Classic and no 802.15.4 radio.
Which ESP32 has the most GPIO pins?
The ESP32-S31 has the most GPIO pins at 60 on the chip, per the Espressif ESP32-S31 datasheet, but the chip was sampling at last check. Among boards you can buy today, the ESP32-P4 has 55 and the ESP32-S3 has 45. A board breaks out fewer pins than the chip total, so check the board pinout.
Does the ESP32-C6 support Matter?
Yes. The ESP32-C6 supports Matter over Thread and Matter over WiFi, per Espressif, combining Wi-Fi 6 at 2.4 GHz with an 802.15.4 radio for Thread and Zigbee and Bluetooth LE 5.3. The ESP32-H2 also supports Matter over Thread, and the ESP32-C5 adds 5 GHz WiFi to the same Matter support.
Which ESP32 should I buy for a battery project?
The ESP32-C3 is the best ESP32 for a battery-powered WiFi project, with deep sleep current around 5 uA. The ESP32-H2 is the best ESP32 for a battery-powered Thread or Zigbee project, with no WiFi radio to feed. Read How to Power ESP32 and Arduino Projects on LiPo Power for the charging, protection, and run-time math: the board draws more than the chip deep sleep figure.
Parts used in this guide
If you already know which ESP32 should I buy for your project, the boards below are in stock in the store and linked to their product pages. Use the product page for the current listing. Product images in the body link to their products.
ESP32 DevKit V1 Development Board, 30-Pin WROOM-32, WiFi + Bluetooth, Dual-Core – Classic ESP32.
ESP32-S3 Development Board DevKitC-1 N8R2 N16R8 WiFi BT Module 44Pin Type-C USB ESP32-S3 – ESP32-S3, the default pick.
ESP32-S2 Mini Development Board, WiFi, 4MB Flash, 2MB PSRAM, USB-C – ESP32-S2.
ESP32-C3 SuperMini Development Board 4-Pack, RISC-V 160MHz, WiFi + Bluetooth LE – ESP32-C3.
Seeed Studio XIAO ESP32C6 Development Board, 1-Pack – ESP32-C6.
Seeed Studio XIAO ESP32-C5 Development Board, 1-Pack – ESP32-C5.
ESP32-H2 SuperMini Development Board, RISC-V 96MHz, BLE + Zigbee + Thread – ESP32-H2.
ESP32-CAM WiFi Board with ESP32-CAM-MB Micro USB Carrier, OV2640 Camera Module, Single – ESP32-CAM.
ESP32-S3-N16R8 CAM Development Board with OV5640 Camera, Dual USB-C, WiFi + Bluetooth 5 – ESP32-S3-CAM.
In this series
This pillar is post 1 of 10. The spoke posts below come next in this series. Their links are added here when each post publishes.
- Post 2: ESP32 DevKit V1 (30-pin) pinout.
- Post 3: ESP32-S3 DevKitC-1 pinout.
- Post 4: ESP32-CAM pinout, boot mode, and flashing.
- Post 5: ESP32-CAM troubleshooting.
- Post 6: ESP32-CAM streaming.
- Post 7: ESP32-CAM on battery.
- Post 8: ESP-NOW explained.
- Post 9: Arduino IDE vs PlatformIO vs ESP-IDF vs MicroPython for ESP32.
- Post 10: ESP32 not detected over USB.
Related guides
- ESP32-CAM vs ESP32-S3-CAM: Which Camera Board to Pick
- How to Use the ESP32-S3-CAM Board for Camera Projects
- Seeed XIAO ESP32S3 Guide: Standard Board vs Sense Board
- How to Pick an ESP32 SuperMini Board for Tiny Builds
- XIAO ESP32C3 vs C6 vs S3 vs C5: Pick the Right Board
- How to Choose ESP32 Boards for Your Robotics Projects
- How to Choose ESP32 Boards for Drones and FPV Projects
- ESP32 Boards with Built-In Displays: TFT vs OLED Compared
- Arduino vs ESP32 vs RP2040: Which Dev Board for Your Robot
- How to Power ESP32 and Arduino Projects on LiPo Power
- How to Use NodeMCU ESP8266 with a Built-In OLED Display
Sources
- Espressif ESP32-S31 product page: dual-core 32-bit RISC-V up to 320 MHz, 512 KB SRAM, 60 GPIO pins, Wi-Fi 6, Bluetooth 5.4 LE and Classic, 802.15.4, Gigabit Ethernet, USB OTG high speed, 8 to 32 MB PSRAM. https://www.espressif.com/en/products/socs/esp32-s31
- ESP32-S31 Series Datasheet, pre-release v0.6: HP dual-core RISC-V up to 320 MHz, LP core up to 40 MHz, 60 GPIO pins, Wi-Fi 6, Bluetooth 5.4, Zigbee 3.0, Thread 1.4. https://documentation.espressif.com/esp32-s31_datasheet_en.html
- ESP32-P4 Series Datasheet, pre-release v0.7: dual-core RISC-V up to 400 MHz, 768 KB SRAM, 16 or 32 MB PSRAM, 55 GPIO pins, MIPI-CSI and MIPI-DSI, H.264 encoder, USB 2.0 high-speed OTG, no radio. https://documentation.espressif.com/esp32-p4_datasheet_en.html
- Zephyr Project, ESP32-C5 features: HP RISC-V core up to 240 MHz, 384 KB SRAM, dual-band Wi-Fi 6, Bluetooth 5.4 LE, 802.15.4, 29 GPIO pins. https://docs.zephyrproject.org/latest/boards/espressif/common/soc-esp32c5-features.html
- Espressif ESP32-C5 datasheet (mirror of the Espressif PDF): HP RISC-V core up to 240 MHz, LP core up to 40 or 48 MHz, 384 KB HP SRAM, 16 KB LP SRAM, Bluetooth Core 6.0 certified, Thread 1.4, Zigbee 3.0, 29 GPIO pins. https://www.alldatasheet.com/datasheet-pdf/pdf/2162612/ESPRESSIF/ESP32-C5.html
- Espressif series datasheets for ESP32, ESP32-S2, ESP32-S3, ESP32-C3, ESP32-C6, and ESP32-H2: cores, clocks, radios, SRAM, GPIO counts, and USB support in the comparison table, cross-checked against the Espressif data quoted in the JLCPCB ESP32 versions guide, the Blynk ESP32 variant guide, and the esp32.iammanis.com specifications table.
