To record analog FPV video, feed your receiver output into a recorder and start it before takeoff. Three routes work: a USB capture adapter into a PC running OBS Studio, a DVR built into your goggles or a monitor, or a UVC app on a phone. The recording shows exactly what the receiver saw, static included, so fix the picture before you press record. Fly from your goggles, not from the recording screen.
How does analog FPV video reach a recorder?
Analog FPV video travels as a continuous composite video signal, not as digital data. The chain is short: the camera sends composite video to the video transmitter, the transmitter sends it over the air on the 5.8GHz band, a receiver on the bench picks it up, and the receiver hands composite video out of its RCA video socket. A recorder sits at the end of that chain and saves what the receiver outputs. If you have not got the signal into a computer yet, read the QRC conversion guide first: How to Convert Analog FPV Video to USB on a Computer. It covers the two routes in full, receiver plus USB capture adapter and UVC OTG receiver, with signal troubleshooting. Digital FPV systems (DJI, Walksnail, HDZero) do not use this chain: their video is a digital stream, not analog composite video, so this adapter does not work with them.
What are the three ways to record analog FPV video?
Pick the recorder by where you want the file and what you already own. All three record the same feed: what the receiver saw, including every breakup.
| Route | Where the file lands | Best for | Main limit |
|---|---|---|---|
| PC with USB capture adapter | PC hard drive | Best files to edit and share, streaming | Needs a PC at the field or bench |
| Goggle or monitor DVR | Micro SD card in the goggles or monitor | Crash investigation, zero extra gear while flying | Lower quality than PC capture, card not included |
| Phone with UVC receiver | Phone storage | Spectating, ride-along video, no PC | QRC does not currently stock a UVC receiver |
The PC route gives the cleanest editable files. The DVR route is the one most pilots actually use, because it needs nothing extra while flying.
What will the recording look like?
Analog FPV video is low resolution by modern standards, and every recorder here saves the received signal, not the camera’s original picture.
Resolution. The analog DVR guide at UAVModel notes most analog DVRs record at 30 frames per second, with bitrate typically locked between 6 and 12 Mbps, which is adequate for 640×480 or 720×576 resolution but breaks down with complex detail, rapid motion, or static interference. The QRC capture adapter listing states 720P USB video output, NTSC and PAL.
Static is recorded, not removed. The recording shows the same breakups you saw while flying. The QRC goggles guide puts it plainly: a DVR records exactly where the quad went down, and the recording is lower quality than an action camera and shows the same breakups you saw while flying. Clean footage of the flight itself needs an onboard recorder or an action camera on the quad.
Latency. The analog link itself adds effectively no processing delay, because the signal is a continuous waveform with no encode and decode step, A USB capture adapter and OBS add a processing step, so the PC screen lags behind the goggles. No latency number in milliseconds is stated here, because no primary source or named test was found to support one. Fly from the goggles, never from the recording screen.
Audio. Most analog FPV cameras send video only, so expect a silent file unless your camera has a microphone. The adapter passes audio through if the source carries it.
How do I record analog FPV video on a PC with a USB capture adapter?
This is the full OBS setup. It assumes the receiver is already locked onto the VTX channel and the picture is clean. Recording a bad signal only preserves it.
1. Connect the chain. Plug the receiver composite video output into the adapter RCA input, using the yellow plug for video. Plug the adapter into a USB port on the computer. The Media-Tech MT4169 video grabber manual advises using a USB port on the back of a desktop computer and avoiding front panel USB ports or hubs, because they can cause signal problems.
2. Check the computer sees the adapter, then add it in OBS Studio. On Windows, open the Camera app. On Mac, open Photo Booth or FaceTime and look for the adapter in the camera list. If nothing appears, try a different USB port and cable. OBS Studio is free, runs on Windows, Mac, and Linux, and is the program the MT4169 manual recommends. In the Sources panel, click the plus sign, select Video Capture Device, create a new source, and pick the adapter from the device list. If the feed does not appear in the OBS preview, check the Windows camera permission first: Settings, Privacy and Security, Camera. If your camera has a microphone, add an Audio Input Capture source in OBS and pick the adapter. If you hear nothing, check the Windows microphone permission at Settings, Privacy and Security, Microphone.
3. Set the recording output before you record. Open File, Settings, Output, Recording. Set the recording format to MKV, not MP4. The QuantumWarp analog capture guide recommends MKV, because if the computer crashes mid-recording, an MKV file is usually still playable, while an MP4 file is often lost. OBS can remux the finished MKV to MP4 afterwards under File, Remux Recordings. Set the recording path to a drive with free space, and record a short test clip first.
| OBS setting | What to pick | Why |
|---|---|---|
| Recording format | MKV | Survives a crash mid-recording; remux to MP4 later |
| Recording path | A drive with free space | A full drive stops the recording |
| Encoder | Hardware encoder if OBS offers one, otherwise software x264 | Keeps the PC responsive while recording |
| Source | One Video Capture Device, the adapter | One source keeps the file clean |
| Test clip | Record 30 seconds, play it back | Confirms picture, format, and file location before the flight |
4. Record. In the Controls panel, click Start Recording, then fly. Click Stop Recording before you power anything down. Keep the scene to the single capture source: anything on screen in OBS is burned into the recording and cannot be removed later.
How do I record with a DVR in goggles or on a monitor?
A DVR built into goggles or a monitor records the received feed onto a micro SD card. It is the simplest route because it needs no computer and no extra box, and it records exactly what you saw.
Start the DVR before takeoff. The QRC goggles guide notes that Oscar Liang starts the DVR before every takeoff for exactly this reason: the last seconds of the flight are the ones that show where the quad went down.
Use a fast card, and format it in the goggles. The UAVModel DVR guide advises a high-quality U3 or V30 rated micro SD card with at least 64GB capacity, formatted in the goggles before each session. The Eachine EV800D goggles stocked at QRC do not include a card in the box, so buy one separately.
Turn off the overlays that get burned into the file. If your goggles allow it, disable the on-screen recording timer and recording status indicator. The UAVModel guide is direct about why: these overlays are burned into the video and cannot be removed later.
Pick the file format if the menu offers one, and play it back in the goggles. The UAVModel guide advises setting the recording format to MOV rather than AVI when the goggles offer the choice, because MOV files handle dropped frames more gracefully. Most goggles with a DVR let you play the footage back inside the goggles, so you can watch the last seconds at the field and walk straight to the crash site. The stocked DVR units are in the Parts block below. The basic 4.3-inch monitor and the 3-inch micro monitor have no DVR, so they can show the feed but cannot record it.
How do I record analog FPV video on a phone?
The phone route uses a UVC receiver: a 5.8GHz receiver with a USB output built in, plugged straight into the phone. The phone treats it like a webcam, and the UVC app records the feed. The conversion guide states the key point in one line: a UVC receiver also works as a cheap DVR, because your phone records the feed. Use the app that came with the receiver first. If the app shows the feed but has no record button, use the phone screen recorder instead: an Instructables build from 2016 notes that the EasyCAP Viewer app did not record at the time, and the author captured the screen with a screen recorder. That workaround records whatever is on the phone screen, so keep notifications off. Quality RC Parts does not currently stock a UVC receiver, so buy one that lists UVC support for your phone. For the full phone setup, see Method 2 in the conversion guide linked above. iPhone support for UVC is thinner than Android, so check compatibility for your exact phone before you buy.
What do I do with the files after the flight?
Copy the files off the card or drive before you edit anything. Do not edit from the SD card: a card that is still in the goggles is easy to format by accident, and editing from it is slow.
Convert variable frame rate to constant frame rate before editing. The UAVModel guide notes that many goggle DVRs produce variable frame rate files that cause audio sync issues and stuttering in editing software, and advises converting to a constant frame rate with a tool like HandBrake in a single pass. Do this before you cut anything.
Clean up the picture lightly, and upscale before uploading. The UAVModel post-processing advice is a subtle sharpen filter at 0.3 to 0.5 strength, a slight contrast boost, and a saturation increase of 10 to 15 percent. Upscale analog DVR footage to 1080p when rendering for YouTube or social media, because the higher resolution forces the platform to use a better compression codec.
What are the common mistakes?
- Starting the recorder after takeoff. The useful seconds are the last ones. Start the DVR or OBS recording before the quad leaves the ground.
- Recording a weak link and blaming the recorder. Static in the file means static in the feed. Fix antennas, channel, and VTX power first.
- Leaving the recording timer on screen. It is burned into the file and cannot be removed later.
- Recording to MP4 in OBS. A crash mid-recording can lose the whole file. Record MKV and remux afterwards.
- Forgetting the SD card. The EV800D does not include one. A DVR with no card records nothing.
- Using a slow card. A card below U3 or V30 can drop frames or stop the recording. Format it in the goggles before the session.
- Flying from the PC screen. The USB capture path lags behind the goggles. Watch and record on the PC, fly from the goggles.
How do I fix a recording problem?
OBS sees the adapter but shows no image. Check the Windows camera permission at Settings, Privacy and Security, Camera. Then check that the receiver is powered and on the right channel, and try a rear motherboard USB port instead of a front panel port or hub.
OBS shows the video but there is no sound. Check the Windows microphone permission at Settings, Privacy and Security, Microphone, then add an Audio Input Capture source for the adapter in OBS.
The recording stutters or drops frames. Close other programs, switch OBS to a hardware encoder if one is available, and record to a drive with free space. If the finished file stutters in an editor but plays fine in a player, convert it from variable frame rate to constant frame rate with HandBrake.
The DVR did not record. Check the card is in the goggles, has free space, and was formatted in the goggles. Check that you started the DVR before takeoff. A card that works in a computer does not always work in goggles.
The file will not play. Try VLC first, since it plays more formats than most players. If an OBS MKV file will not open in your editor, remux it to MP4 in OBS under File, Remux Recordings. If a DVR file will not open, try the MOV format next time.
The recording stops early. The card is full, too slow, or failing. Copy the files off, format the card in the goggles, and replace a card that keeps failing.
Which recording route should I pick?
| Your goal | Pick this route | Why |
|---|---|---|
| Crash record while flying with goggles | Goggle DVR | Already there, playback in the goggles at the field |
| Best files to edit, share, or stream | PC with USB capture adapter and OBS | Record MKV, remux to MP4, convert frame rate before editing |
| Big shared screen at the field | Monitor with a DVR | A spotter sees the same feed, and the DVR records it |
| Spectate or record on a phone, no PC | UVC receiver with a UVC app | Simplest setup, but QRC does not currently stock a UVC receiver |
| Cleanest possible footage of the flight | None of these | All record the received feed. That needs an onboard recorder or an action camera on the quad |
| ## Parts used in this guide |
Prices and stock were verified live on qualityrcparts.com on 2026-11-21. All four items below are in stock and purchasable.
- USB Video Capture Adapter RCA to USB for FPV (ID 23526) – $19.99. RCA composite video and S-Video input, 720P USB video output per the listing, NTSC and PAL, USB 2.0 USB-A plug, driver installs automatically, USB powered, captures audio. Works with OBS Studio or PotPlayer on Windows and QuickTime Player on Mac, per the listing.
- Eachine EV800D FPV Goggles 5 Inch 800×480 5.8GHz 40CH Diversity DVR (ID 13166) – $264.99. 5-inch 800×480 screen, 40-channel diversity receiver, built-in DVR, 7.4V 1200mAh battery. Micro SD card not included.
- 4.3 Inch FPV Monitor with DVR, 5.8GHz 40CH, 800×480 IPS Display (ID 22098) – $153.99. 800×480 IPS display, 40-channel receiver, built-in DVR.
- 7 Inch FPV Monitor with DVR, 5.8GHz 40CH Diversity Receiver, 1024×600 HD Screen, Built-in Battery and Sunshade (ID 20961) – $251.99 sale, $302.99 regular. 1024×600 screen, 40-channel diversity receiver, built-in DVR, removable rechargeable battery, foldable sunshade.
Shipped fast and securely from our secure facility in Queensbury, NY. QRC ships within the USA only.
Related guides
- How to Convert Analog FPV Video to USB on a Computer
- How to Choose FPV Goggles or a Monitor for Your First Kit
- Best FPV Cameras for Racing in the USA
- FPV Crash Inspection: Repair and Parts Checks
- Best FPV Cameras for Night Flying
FAQ
Can I record analog FPV video on my PC? Yes. Connect the receiver composite video output to a USB video capture adapter, plug the adapter into the PC, add it as a Video Capture Device in OBS Studio, and press Start Recording. Source: Media-Tech MT4169 video grabber manual.
What resolution does a USB capture adapter record at? It records the analog signal it is given, not a fixed high resolution. The QRC adapter listing states 720P USB video output. The ivcan CVBS to USB converter lists 800×600 and 640×480 at 30 frames per second for its own device. Expect standard definition footage, not HD.
Do I need drivers for a USB video capture adapter? Usually no. The QRC adapter listing says its driver installs automatically when you plug it into a PC, and the MT4169 manual says Windows 10 and 11 detect this class of device automatically.
Can I use a USB video capture adapter for live streaming? Yes. OBS Studio records and streams from the same source, so the adapter feed can go to a stream as well as to a file. The ivcan converter FAQ lists live streaming as a supported use for this class of device.
Why does my DVR footage look worse than what I saw in the goggles? Analog DVRs compress video in real time with hardware encoders that prioritize low latency over image quality, and most record at 30 frames per second with bitrate locked between 6 and 12 Mbps. Source: UAVModel FPV goggle DVR guide.
What SD card should I use in a goggle DVR? A high-quality U3 or V30 rated micro SD card with at least 64GB capacity, formatted in the goggles before each session. Source: UAVModel FPV goggle DVR guide.
Can I record FPV video on my phone? Yes, with a UVC receiver and a UVC app: the phone records the feed, so the receiver works as a cheap DVR. If the app shows the feed but has no record button, use the phone screen recorder instead. Source: QRC conversion guide, Instructables EasyCAP build.
Why is there no sound in my recording? Most analog FPV cameras send video only, so a silent file is normal. If your camera has a microphone, check the Windows microphone permission and add an Audio Input Capture source for the adapter in OBS. Source: Media-Tech MT4169 video grabber manual.
Sources
- Quality RC Parts, How to Convert Analog FPV Video to USB on a Computer: https://qualityrcparts.com/convert-analog-fpv-video-usb/
- Quality RC Parts, How to Choose FPV Goggles or a Monitor for Your First Kit: https://qualityrcparts.com/best-fpv-goggles-and-monitors-usa/
- Quality RC Parts, Best FPV Cameras for Racing in the USA: https://qualityrcparts.com/best-fpv-cameras-for-racing-usa/
- Quality RC Parts, FPV Crash Inspection: Repair and Parts Checks: https://qualityrcparts.com/fpv-crash-inspection-repair-parts-checks/
- Quality RC Parts, Best FPV Cameras for Night Flying: https://qualityrcparts.com/best-fpv-cameras-for-night-flying/
- Quality RC Parts store listings, checked live 2026-11-21 (IDs 23526, 13166, 22098, 20961)
- OBS Studio: https://obsproject.com/
- Media-Tech MT4169 Video Grabber installation and user guide: https://manuals.plus/m/d4338795f18d75bc50ab1456444af3b44b1a582fd2fa37813bb4df4d30cee7e8
- QuantumWarp, Capture Analogue Video Cassette Tapes: https://Quantumwarp.com/kb/articles/31-media/1009-capture-vhs-video-cassette-tapes
- UAVModel, FPV Goggle DVR and Recording: Best Settings for HD and Analog Footage: https://blog.uavmodel.com/6063-2/
- ivcan, FPV Camera CVBS AV to USB Converter analog video capture: https://ivcan.com/p/fpv-camera-cvbs-av-to-usb-converter-analog-video-capture/
- Mode 2, FPV video: analogue vs digital, antennas and VTX power: https://mode-2.com/components/video/
- EEVblog, DVRs for capturing analog thermal video: https://www.eevblog.com/forum/thermal-imaging/dvrs-vor-capturing-analog-thermal-video-your-experiences/?action=printpage
- Instructables, Easycap With 5.8GHz Integrated Receiver for FPV: https://www.instructables.com/Easycap-With-58Ghz-Integrated-Receiver-for-FPV-for/
Last updated: 2026-11-21
