Filament Refill Spool Adapter Guide: Fit and Load

A filament refill spool adapter lets a spool-less coil of filament ride on a spool it was not made for. A refill is filament wound as a coil with no spool included. It costs less per kilo than the same filament on a spool, but it cannot print until it sits on something that holds its shape and keeps it centered. When they come from different systems, the adapter is the bridge.

This guide covers what an adapter does, the four adapter types, how to check the fit, and how to load a refill without tangles. For which filament to print RC and drone parts with, read PLA vs PLA+ vs PETG: Pick the Right 3D Printer Filament for Drone Parts. For refill prices and break-even math, read Filament Refill vs Spool: How Anycubic Refills Save You Money.

What does a filament refill spool adapter do?

A refill coil is a wound roll of filament held together by straps or tape, with a hollow center and no flanges. On its own it cannot mount on a printer or feed at a steady tension. A reusable spool gives it flanges to contain the sides, a hub to center the coil, and a lock to hold the two halves together.

An adapter does one of three jobs. It changes the hub size, filling the gap between the refill core and the spool hub so the coil sits centered. It changes the locking interface, carrying the notch, key, or seat the refill expects on one side and the shape the spool expects on the other. Or it changes the coil width, filling the gap when a refill is narrower than the spool. The adapter only changes how the coil is held.

Do you need an adapter, or just the matching spool?

Start here, because the cheapest answer is usually no adapter at all.

Your situation What you need
You buy a refill made for the reusable spool you own Nothing. Load the refill on the matching spool.
You buy your first refill and own no reusable spool The matching reusable spool, not an adapter.
You own a reusable spool from one system and a refill from another An adapter, if one exists for that pair. Check the fit first.

The stocked example makes the point. The Anycubic Reusable Filament Spool for 1kg Refills (ID 23527) at $13.99 takes 1kg Anycubic refill coils in 1.75mm, in PLA, PLA+, and PETG. One spool serves every refill of that size, and the refill chips move onto the spool flanges so an ACE Pro printer still reads the material, color, and remaining volume.

What are the four adapter types?

1. The brand-matched reusable spool

Two spool halves, made for one refill system, twist or snap together around the coil. The Anycubic spool in this guide is this type: two halves, a threaded connection, a twist lock with a click, and a 196 x 67mm size stated on the listing. It is ABS, rated high-temperature resistant up to 80C per the listing. Buy this type first when it exists for your refill. It is the only type where fit is guaranteed by the maker.

2. The adapter plate

An adapter plate is a flat printed ring that sits between one spool half and the refill. It exists because some reusable spools have a notched interface that a refill from another system does not match. Filamentive publishes this design for its refills used with a Bambu Lab reusable spool. The plate only translates the notch. It adds no width and no hub, so it only works when the refill core already fits the spool hub and the coil width already matches the spool.

3. The printed MasterSpool

A MasterSpool is a reusable spool you print yourself, in two halves, and load refill coils onto. Filamentive publishes a printed masterspool for its refills, printed twice, one half per print. A printed Prusament to MasterSpool adapter works the same way in reverse, converting an empty Prusament spool into one that accepts refills with a press fit. The model author recommends PETG, notes PLA might work but is untested, and warns to test print a 1cm tall section of the fit ridge first, because the fit depends on your printer calibration.

A printed spool is only good up to the softening temperature of the filament it was printed from, per forum reports cited in the refill vs spool guide on this site. Print adapter parts in PETG or a higher temperature material when the spool will see dryer heat.

4. The cardboard-spool collar adapter

Some filament ships on cardboard spools. When the filament runs out, the cardboard core is still a usable spool body, and a collar adapter turns it into a reusable spool for refills. The adapter is two collars that connect to each other inside the cardboard core with a tab system, plus a hole that holds the filament end by friction. Published models list separate collar sizes for different cardboard spool brands, because core sizes differ by several millimetres between brands. Measure your spool core before you print.

How do you check the fit before you buy or print an adapter?

Four checks, in order. If any one fails, stop. Do not compress the coil to make it fit, and do not remove filament turns to shrink it. Both moves destabilize the coil, per the KJI 3D loading guide.

  1. Coil inner diameter against the hub. The refill core must slide onto the hub or the adapter with a snug fit and no wobble.
  2. Coil width against the spool width. The coil must sit inside the flanges with no section riding above the sidewall. A coil that is too wide keeps the spool halves from closing.
  3. Notch and key alignment. If the spool or the refill has a notch, a cutout, or a key, find it before you place the coil. On the Bambu Lab system the refill has a small cutout next to the identification tag, and the spool has a plastic notch that lines up with it. Forcing a coil against its key pinches the inner turns.
  4. Chip and label placement. Some refills carry identification chips that must move onto the spool flanges. On the Anycubic system, remove both stickers and both chips from the refill, if present, and install the new chip stickers onto both spool flanges before you load the coil.

Before you load filament into the extruder, mount the finished spool on the holder and confirm it rotates freely, with no scraping against the holder, the printer frame, a wall, or a dryer.

How do you load a refill on the stocked reusable spool?

These steps follow the Anycubic loading sequence stated on the live listing for the Anycubic Reusable Filament Spool for 1kg Refills (ID 23527), plus the control principles from the KJI 3D loading guide. The order is the whole method: lock first, straps last.

  1. Label the filament. Remove both stickers and both chips from the refill, if present, and install the new chip stickers onto both spool flanges. The chips travel with the refill, not with the spool.
  2. Open the spool. Separate the two halves and lay the half with the hub facing up on a clean, flat surface. Check both halves for cracked tabs.
  3. Load the coil with its straps still on. Set the refill coil onto the open half, align the filament with the latch, and snap the coil into place. Check the unwind direction so the filament leaves toward the inlet without a sharp bend.
  4. Lock the spool. Close the spool, press firmly, and rotate until you hear a click.
  5. Remove the straps last. Only once the spool is locked, remove the bonding strap and thread the filament into the spool hole. Remove the straps one at a time, keeping one hand on the outer turns. Never remove all restraints at once and then search for the filament end. Put the filament end straight into the retaining hole or clip.
  6. Mount and watch the first minutes. Place the spool on its holder, confirm it turns freely, and feed the filament through any guide tube, sensor, or dry box inlet before it reaches the extruder. Watch the spool turn for the first few minutes. It should unwind smoothly, without the filament catching under a loop or rubbing hard on a spool edge.

For PETG refills, dry the filament first: Anycubic states drying at 55 to 65C for 6 to 8 hours before printing. The stocked spool is ABS and rated high-temperature resistant up to 80C per its listing, so check your dryer temperature against that rating first.

How do you load a refill with an adapter plate or a printed spool?

The pattern is the same for an adapter plate and a printed MasterSpool. Only the parts change.

Adapter plate, following the Filamentive sequence for its refills on a Bambu Lab reusable spool: one half notched side up, adapter on it and lined up with the notch, refill on the adapter with its straps still on, second half on top and spun to lock, then remove the straps. SparkLab states the same sequence: twist apart, align the notch with the cutout, spin until you hear a click, remove the tabs, apply the sticker.

Printed MasterSpool: print both halves in PETG or a higher temperature material, not PLA, if the spool will see dryer heat. For a press-fit adapter, test print a 1cm tall section of the fit ridge first. Place one half flat, set the refill on the core with its straps still on and lined up with the cutouts, place the second half over it and lock it per the model, then unwrap the straps through the cutouts one at a time. Park the filament end in a hole or clip in the flange, then mount the spool and check that it turns freely.

What mistakes tangle a refill?

Most refill tangles are not factory knots. They happen when the free filament end slips under another loop after handling. The KJI 3D guide states the rule plainly: never let go of the filament end unless it is secured in a spool hole, held in your hand, or fed into the printer.

  • Cutting the straps before the spool is locked. The coil loosens, loops cross, and the print jams halfway through.
  • Removing all restraints at once. Cut or release one tie at a time, with a hand on the outer turns.
  • Pulling several feet of filament off the spool to find the end. Release only what the printer route needs.
  • Tucking the loose end between the flanges instead of in the retaining hole. A loose end migrates during storage and creates a crossover that is hard to spot until the print fails.
  • Loading the coil upside down or against its key. If the coil will not sit flush, stop and inspect.
  • Mixing systems without checking the fit first.

Troubleshooting: what went wrong and how do you fix it?

Symptom Likely cause Fix
Spool halves will not close Wrong spool model, coil too wide, or a packaging insert still around the inner diameter Verify the spool model, remove the insert, and check coil width. Do not remove filament turns.
Spool turns with a scraping sound Off-center coil, warped flange, or contact with the holder Re-center the coil, inspect the flange, and check holder clearance.
Filament catches early in the print A strand crossed under another strand, or a loop caught on the spool rim Pause if safe, free the crossover while keeping tension on the filament, then secure the routing.
Filament pops and prints rough Damp filament, usually PETG Dry the filament before printing. Anycubic lists 55 to 65C for 6 to 8 hours for its PETG refill.
Printer does not identify the material Chips not moved to the flanges Move both chips and both stickers from the refill onto the spool flanges before loading.

Which refill should you buy first?

The full comparison lives in PLA vs PLA+ vs PETG: Pick the Right 3D Printer Filament for Drone Parts and in PLA PLA+ PETG Filament: Which to Print RC Parts With. All three stocked refills are 1.75mm, 1KG coils, refill only, with no spool included. All three need a reusable spool, a previous spool, or a printed spool.

Refill Price What the listing states
Anycubic PLA Filament Refill, 1.75mm, 1KG (ID 17667) $19.99 ACE Pro chip. Strong bed adhesion at just 45C.
Anycubic PLA+ Filament Refill, 1.75mm, 1KG (ID 17695) $24.99 Twice the toughness of standard PLA. Plus or minus 0.02mm tolerance.
Anycubic PETG Filament Refill, 1.75mm, 1KG (ID 17689) $18.99 Twice the impact resistance of standard PLA. Plus or minus 0.02mm tolerance. Vacuum packed.

Buy PLA+ first for drone parts that take hits. Buy PETG first for parts that flex, get wet, or live outdoors. Buy PLA first only if you prototype a lot. For ASA and nylon, read PETG vs ASA vs Nylon: Best Filament for RC Parts. For per-part FPV picks, read Best Filament FPV Drone Builders Use for Frames and Mounts.

Parts used in this guide

All products below were verified live and in stock on 2026-11-21, at the live store prices shown. Re-verify at publish time. In-stock parts ship from our secure facility in Queensbury, NY, within the USA only.

  • Anycubic Reusable Filament Spool for 1kg Refills (ID 23527), $13.99. Two halves, threaded connection, twist lock with a click. Fits 1kg refill coils in 1.75mm, PLA, PLA+, and PETG. Spool size 196 x 67mm, ABS, up to 80C per the listing. No filament included.
  • Anycubic PLA Filament Refill, 1.75mm, 1KG (ID 17667), $19.99. Refill coil only, no spool included. ACE Pro chip, strong bed adhesion at 45C.
  • Anycubic PLA+ Filament Refill, 1.75mm, 1KG (ID 17695), $24.99. Refill coil only, no spool included. Twice the toughness of standard PLA, plus or minus 0.02mm tolerance.
  • Anycubic PETG Filament Refill, 1.75mm, 1KG (ID 17689), $18.99. Refill coil only, no spool included. Twice the impact resistance of standard PLA, plus or minus 0.02mm tolerance, vacuum packed.

No standalone spool adapter product is stocked. The stocked answer is the reusable spool itself (ID 23527), which fits the three refills above with no adapter needed. The adapter section of this guide is method only, not products sold here.

Related guides

Frequently asked questions

What does a filament refill spool adapter do?

It bridges a spool-less refill coil and a spool it was not made for. It changes the hub size, the locking interface, or the coil width so the coil sits centered, stays contained by the flanges, and turns smoothly on the printer.

Do I need an adapter if I buy the matching reusable spool?

No. A refill made for your spool fits out of the box, and the Anycubic reusable spool in this guide takes the three stocked 1kg refills with no adapter needed. You need an adapter only when the refill and the spool come from different systems.

Will any refill fit any reusable spool?

No. A refill that looks close in diameter may still sit too loosely, rub the spool edges, or fail to lock onto the hub. Check the four fit checks in this guide first: coil inner diameter against the hub, coil width against the spool width, notch and key alignment, and chip placement.

Can I print my own spool adapter?

Yes, and the MasterSpool project is the standard way to do it. Print both halves, load the refill with its straps still on, lock the halves, then remove the straps through the cutouts. Use PETG or a higher temperature material, not PLA, if the spool will see dryer heat.

Why does my refill tangle after loading?

Most refill tangles are not factory knots. They happen when the free filament end slips under another loop after handling, or when the straps come off before the spool is locked. Lock the spool first, remove the straps one at a time, and park the filament end in the retaining hole the moment the last strap is off.

Can I use a refill spool in a filament dryer?

It depends on the spool material. The stocked Anycubic reusable spool is ABS and rated high-temperature resistant up to 80C per its listing, so it can go in most dryers. A printed spool is only good up to the softening temperature of the filament it was printed from.

Do I need to move the chip when I load a refill?

If your refill carries identification chips, yes. On the Anycubic system, remove both stickers and both chips from the refill, if present, and install the new chip stickers onto both spool flanges before you load the coil. The printer reads the material, color, and remaining volume from the chips on the flanges.

Sources

Remote ID Setup: Install, Register, and Pre-Flight Check

A Remote ID module only works when three things are done in order: mount and power it correctly, register its serial number in FAA DroneZone, and verify the broadcast before takeoff. Skip any one of them and the drone is not compliant. This guide walks through all three, then gives you a pre-flight checklist to run every time you fly.

If you have not bought a module yet, start with How to Choose a Broadcast Remote ID Module.

Step 1: Check the FAA DOC list before you mount anything

Do this before you mount the module. A module that is not on the FAA Declaration of Compliance list does not meet the rule, no matter how well it works as a radio. No firmware update and no DroneZone entry can fix an unlisted module.

Have the module serial handy: it is on the sticker on the module case, in the companion app, or on the box. Source: Spektrum SkyID manual; FAA Remote ID page.

Open the FAA UAS Declaration of Compliance list at uasdoc.faa.gov. Search by the maker name, filter by Remote ID, and match the exact model name and FCC ID. A close name is not a match. Check the serial range in the entry too: some entries cover only part of a production run. Source: FAA Remote ID page; post 17349.

The list returned a live 200 response on 2026-11-21 and loads as a searchable web app. If the search returns nothing for your model, treat the module as unlisted. If the seller cannot name the DOC entry, do not buy it. Source: live fetch 2026-11-21; post 17349.

Warning: this guide makes no per-module DOC claim. The choosing guide 17349 makes none, and neither does this draft. Only a live lookup on uasdoc.faa.gov on the day you buy tells you whether a module counts.

The Holybro module needs a special note. It is a Standard Remote ID solution for manufacturers and integrators, not a plug-and-play retrofit, and it needs its own Declaration of Compliance submission in the USA. The choosing guide 17349 and the QRC DroneZone guide both record that it has no verified DOC entry as an end-user broadcast module. Do not enter its serial in DroneZone unless a DOC entry covers your build. Source: post 17349; QRC DroneZone guide.

Step 2: Mount a standalone module on the aircraft

A standalone module carries its own battery and GPS, turns on with a button, and needs no wiring into the aircraft. Mounting is the whole physical job. Get the position wrong and the module may not get a GPS fix or may not be heard by receivers.

Charge it first. Charge the module fully over USB before the first use. The Holyton manual states a full charge takes about 40 minutes and gives up to 5 hours of operation. Source: Holyton manual; Ruko R111 manual.

Pick the spot. Mount the module on the flat upper surface of the drone, clear of the propeller arc, clear of carbon fiber and metal above the case, and clear of other electronics. Carbon fiber blocks radio signal, so a module buried under a carbon top plate may broadcast weakly or not at all. Source: Holy Stone manual; Spektrum SkyID manual; post 17349.

Fix it twice. Attach the module with the supplied hook and loop pads, then add a zip tie through a frame arm or landing gear as a backup. Adhesive pads fail in heat and after hard landings. Check by hand that the module cannot shift, slide, or rotate into a propeller. Source: Holy Stone manual; Ruko R111 manual; post 17349.

Do not block the drone GPS, then weigh the aircraft. Keep the module clear of the drone own GPS antenna: the Ruko manual warns that a module placed over the drone GPS can block it. If your drone takes longer than usual to get a GPS lock after fitting the module, move the module first. Then weigh the whole aircraft, module included: a 249 gram drone plus a 19 gram module is over 250 grams, which triggers registration. Source: Ruko R111 manual; post 17349.

Step 3: Bind the module to your drone in the app

Most standalone modules need the drone details stored in the module before the first flight. This is called binding: the module broadcasts the serial number and position, and the binding ties that broadcast to your aircraft model and weight in the companion app.

Power on and enter setting mode. The sequence is the same shape across the common manuals, but the exact buttons differ by model, so follow your manual. On the Holyton module, hold the power switch for 3 seconds to turn it on, then hold the settings switch for 3 seconds to enter the setting steps. On the Ruko R111, press the power switch for 3 seconds, then press the settings button for 3 seconds. Then open the maker companion app, tap the device serial number to connect, enter the aircraft model and weight, and save. Source: Holyton manual; Ruko R111 manual.

Restart the module so the binding sticks. This is the step most people skip. On the Holyton module, hold the power switch again to restart: the binding succeeds only after the module is restarted. On the Ruko R111, restart the device until the indicator on the right side blinks rapidly. If you change the binding later, repeat the whole sequence, including the restart. Source: Holyton manual; Ruko R111 manual.

Wait for a GPS fix outdoors, then read the status light. A broadcast module can only send broadcast data when it has a GPS signal, and it needs a clear view of the sky. The Ruko manual states GPS search time is 90 to 120 seconds outdoors. Check GPS outdoors, not indoors: no position indoors is usually fine, while no position outdoors after two minutes is a real problem. Per the Spektrum SkyID manual, a slow flash means it is still acquiring GPS, a solid light means ready, and a rapid flash means an error, so do not fly. Source: Ruko R111 manual; Spektrum SkyID manual.

Step 4: Wire the Holybro module to a flight controller

This step is only for the Holybro Remote ID module on a PX4 or ArduPilot build. It does not apply to a standalone module, which needs no wiring. The Holybro module has no GPS of its own and takes power and position data from the flight controller, so it only fits builds with a flight controller that can feed it. If your aircraft has no flight controller, you need a module with its own GPS instead. Source: post 17349.

The Holybro module runs ArduRemoteID firmware on an ESP32-C3 radio, broadcasts over WiFi and Bluetooth, and connects to the flight controller over CAN or serial. It weighs 27.5 grams with case and antenna and takes 5V from the flight controller. It is a Standard Remote ID solution for manufacturers and integrators, not a plug-and-play retrofit. Source: Holybro Remote ID user manual v1.1; post 17349; QRC listing for ID 13414.

Connect it over serial or CAN. Over serial, connect the module to the flight controller through the Remote ID serial port with the 6-pin GH wire, using the MAVLink or TELEM interface. Over CAN, connect it through the Remote ID CAN port using the DroneCAN interface. Pick the port your flight controller has free, wire it per the manual, and do not share the port with another device. The Matek F405-WING V2 flight controller in the parts block below is an ArduPilot fixed-wing controller that provides the feed a module like this needs. Source: Holybro Remote ID user manual v1.1.

Set the ArduPilot parameters. In Mission Planner, with ArduPilot version 4.x or newer, set DID_ENABLE to 1, DID_OPTIONS to 1, and DID_MAVPORT to the serial port the module is wired to. For the CAN path, follow the manual CAN section for the port setup. Check the module status in your ground station after setting the parameters: ArduPilot shows Remote ID status in Mission Planner and QGroundControl. Do not fly until the ground station shows the module communicating with the autopilot. Source: Holybro Remote ID user manual v1.1; post 17349.

Update the firmware over WiFi if needed. The module acts as a WiFi access point by default. Connect to the RID network with the default password from the manual, open http://192.168.4.1, and upload the ArduRemoteID firmware file for the ESP32-C3 from the releases page on GitHub. A failed update reverts to the factory firmware. Source: Holybro Remote ID user manual v1.1.

Step 5: Register the module serial in DroneZone

Registration is the paperwork half of compliance; the module is the hardware half. A module that is fitted but not registered does not complete compliance. The full walkthrough is in the QRC guide How to Register a Drone and Remote ID in DroneZone. The condensed steps below follow the FAA Remote ID page directly. Create a DroneZone account before the flight day, not at the field.

Know which registration you hold. Recreational flyers register the pilot once, and one registration number covers every drone in the inventory for 3 years. Part 107 pilots register each drone separately, each with its own registration number, at $5 per drone for 3 years. Recreational registration costs $5 and lasts three years. You need your address, email, phone number, the drone make and model, the Remote ID serial number, and a payment card. Source: FAA Remote ID page; FAA register drone page.

Enter the serial in your device inventory. Log in to FAA DroneZone and open the Drone Owners and Pilots Dashboard. Click Manage Device Inventory, then Add Device. Answer Yes to the Remote ID question. Choose the device type: Remote ID broadcast module, or Standard Remote ID drone. Enter the Remote ID serial number from the module, then click Add Device. The serial is on the module case or in the companion app, and it is not the same as the drone serial number. Source: FAA Remote ID page; Spektrum SkyID manual.

Recreational pilots: one module can move between drones. If you use one broadcast module on several drones that lack built-in Standard Remote ID, select broadcast module for each drone and enter the same module serial number on each drone record, with each drone make and model listed. Part 107 pilots do not get this: each device must be registered separately, each with its own registration number. For a drone already registered under Part 107, edit its record the same way and save. Source: FAA Remote ID page.

Mark the drone and carry the certificate. Write the registration number on the outside of the drone before you fly. Print or save the registration certificate and carry it when you fly. Open the drone record in DroneZone after you save it and check that the Remote ID answer reads yes with the serial shown. Source: FAA Remote ID page; QRC DroneZone guide.

Step 6: Verify the broadcast before takeoff

A record in DroneZone and a module on the aircraft are not proof the broadcast works. Verify it with a receiver before every first flight with a new module, and any time the module has been rewired, updated, or moved to another drone. The full verification guide is How to Check Your Remote ID Is Broadcasting.

Open a Remote ID scanner app, turn on Bluetooth and WiFi, and power on the module outdoors with a GPS fix. Your module serial should appear in the app with the right position. Stand within a few meters for the first check: Bluetooth and WiFi broadcasts reach hundreds of meters, not miles. Source: post 17349; post 17351.

For the Holybro module, check the ground station too: open the OpenDroneID OSM app on Android, and check the Remote ID status in Mission Planner or QGroundControl. Finally, confirm the serial in the scanner app matches the serial in your DroneZone inventory. A mismatch usually means the wrong serial was entered. Fix the DroneZone record before you fly. Source: Holybro Remote ID user manual v1.1; post 17349.

The pre-flight checklist

Run this list before every flight with a Remote ID module. It takes two minutes on the ground and catches the failures that ground a flight or break compliance in the air.

  1. Module serial checked on the FAA DOC list, exact model name and serial range confirmed.
  2. Module serial entered in DroneZone, Remote ID answer reads yes, serial shown on the record.
  3. Registration number marked on the outside of the drone.
  4. Registration certificate and TRUST certificate (recreational) carried or saved on your phone.
  5. Standalone module battery charged; add-on module powered from the aircraft.
  6. Module mounted on top, clear of carbon fiber, metal, and the propeller arc, with a zip tie backup.
  7. Drone weighed with the module fitted; registration status correct for that weight.
  8. Module powered on, status light showing ready, not an error flash.
  9. GPS fix acquired outdoors; module position showing in the app or ground station.
  10. Broadcast verified in a scanner app; serial shown matches the DroneZone record.
  11. Flight stays within visual line of sight the whole flight.
  12. If the broadcast stops in flight, land as soon as practicable, then find the fault before the next flight.

Checklist sources: FAA Remote ID page; post 17349; Holyton, Ruko, and Spektrum manuals; QRC DroneZone guide.

What mistakes cause the most failed setups?

  • Checking the DOC list after the first flight. Check it before you pay. A module that is not listed cannot be fixed with a firmware update or a registration entry. Source: post 17349.
  • Entering the drone serial instead of the module serial. The module serial is on the module case or in the companion app. A DroneZone record with the wrong serial does not match the broadcast. Source: post 17349.
  • Skipping the restart after binding. The binding succeeds only after the module is restarted. Save the drone details in the app, then power the module off and back on. Source: Holyton manual; Ruko R111 manual.
  • Mounting under carbon fiber or metal. Carbon fiber blocks radio signal. A module under a carbon top plate may not be heard by receivers, even though its light looks fine. Source: post 17349.
  • Trusting adhesive alone. Hook and loop pads fail in heat and after hard landings. Add a zip tie backup every time. Source: post 17349.
  • Forgetting the weight. A module can push a sub-250 gram drone over 250 grams at takeoff, which triggers registration. Weigh the aircraft with the module fitted. Source: post 17349.

Troubleshooting: the module does not work as expected

The module does not show up in a scanner app. Check that it is powered on and charged. Move the phone closer: Bluetooth and WiFi broadcasts reach hundreds of meters, not miles. Try a second scanner app. Check the mount: a module under carbon fiber or metal may not be heard. Source: post 17349.

No GPS fix. Give the module a clear view of the sky and wait at least two minutes outdoors. A slow flashing status light on the SkyID means it is still acquiring GPS, so do not fly until the light goes solid. Source: Spektrum SkyID manual; Ruko R111 manual; post 17349.

The broadcast drops mid-flight. Land as soon as practicable. Check the battery charge on a standalone module, and check the power connection on an add-on module. Check that vibration has not loosened the mount or the wiring. Source: post 17349.

The Holybro module shows no Remote ID status. The Holybro module needs a flight controller feed over CAN or serial, and the port must be set for Remote ID traffic in the firmware. Check the wiring, check DID_MAVPORT and the other DID parameters in Mission Planner, and check the module status in your ground station. Check that the flight controller has a GPS lock, since the module has none of its own. Source: Holybro Remote ID user manual v1.1; post 17349.

Which setup path fits your drone?

Your aircraft Setup path What to watch
Older consumer drone, recreational flying Standalone module, Steps 1, 2, 3, 5, 6 Charge, top mount, app binding, restart after binding
Homebuilt FPV drone Light add-on module with its own DOC listing, Steps 1, 5, 6, plus the maker wiring steps Weight, free power port, firmware path for your stack
Fixed-wing or long-range PX4 or ArduPilot build Holybro module, Steps 1, 4, 5, 6 Flight controller feed, DID parameters, DOC submission for the build
Part 107 commercial flying One module per drone, Steps 1 through 6 per aircraft Each drone registered separately, each with its own serial entry

For the module choice behind each path, read the choosing guide: How to Choose a Broadcast Remote ID Module.

Parts used in this guide

Prices and stock were verified live on qualityrcparts.com on 2026-11-21. All three items below are in stock and purchasable.

Shipped fast and securely from our secure facility in Queensbury, NY. QRC ships within the USA only.

Related guides

FAQ

Do I need a Remote ID module for my drone? You need one if your drone weighs 250 grams or more at takeoff, or is flown under Part 107 at any weight, and it has no built-in Standard Remote ID, and you do not plan to fly only inside a FAA-Recognized Identification Area. Check the FAA list for your drone first: many drones built since late 2022 already have Remote ID built in. Source: FAA Remote ID page; post 17349.

How do I check if a module is legal before I buy it? Search the FAA UAS Declaration of Compliance list at uasdoc.faa.gov for the exact model name and FCC ID, and check the serial range in the entry. Only a module on the accepted list meets the rule. A close name is not a match. Source: FAA Remote ID page; post 17349.

Where do I enter the Remote ID serial number? Log in to FAA DroneZone, open Manage Device Inventory, click Add Device, answer Yes, choose Remote ID broadcast module, enter the module serial number, and click Add Device. Source: FAA Remote ID page.

Can one broadcast module cover more than one drone? For recreational flyers, yes. List the same module serial number on each drone record in the same inventory, and fly only one drone at a time with it. Part 107 pilots must register each drone separately. Source: FAA Remote ID page.

Why does my module not show up in a scanner app? Check power and charge first, then move the phone closer, then try a second app. A module under carbon fiber or metal may not be heard, and a module with no GPS fix outdoors will not broadcast position. Source: post 17349.

Does the Holybro module work as a plug-and-play retrofit? No. It has no GPS of its own, takes power and position data from the flight controller over CAN or serial, runs ArduRemoteID firmware, and fits PX4 and ArduPilot builds. It is a Standard Remote ID solution for manufacturers and integrators and needs its own Declaration of Compliance submission in the USA. Source: post 17349; Holybro Remote ID user manual v1.1.

Sources

Last updated: 2026-11-21

Night FPV Cameras: Starlight, IR, and Low-Light Picks

A night FPV camera is not a day camera with the brightness turned up. It is a different sensor, a different filter, and a different set of settings. Pick the sensor first, check whether the camera can see infrared light, fit a fast wide lens, and set the OSD. The buying picks live in the companion guide linked below.

How does a starlight sensor see in the dark?

A starlight sensor is a CMOS sensor built to convert very few photons into a usable image. It is the first of three things that make a night camera different from a day camera. The name starlight is a marketing term, not a standard, so judge the sensor by its size, its pixel design, and its published sensitivity.

Back-illuminated pixels. In a back-illuminated sensor the light-sensitive area faces the lens directly, with the wiring behind it, so more of each pixel collects light. Starlight sensors in this class commonly use back-illuminated designs such as Sony STARVIS, named by UAVMODEL for the Ratel 2 and the Cat 3. Source: UAVMODEL.

Pixel size beats pixel count. A sensor with fewer, larger pixels collects more light per pixel, so a 1200TVL starlight camera can out-see a higher-resolution day camera at dusk. Source: Oscar Liang; IRLAB.

Gain, noise, and color. Night flying often pushes gain to 60dB or more. Oscar Liang notes that a good starlight sensor at 60dB of gain looks cleaner than a budget sensor at 40dB, and the Ratel 2 publishes a signal-to-noise ratio of 60dB with AGC off, per the Caddx spec sheet. As light falls, color goes first, so most night cameras switch to black-and-white. Source: Oscar Liang; Caddx spec sheet.

What does a lux figure actually mean?

Lux measures illuminance, the light falling on a surface. A camera lux figure, properly called minimum illumination, is the least light the camera needs to make a usable image. A lower number means the camera sees in less light. The number means nothing without the test conditions behind it.

How much light is out there. Make: Magazine puts real light levels in context: moonless overcast sky 0.0001 lux, moonless clear sky 0.002, full moon 0.27 to 1.0, civil twilight limit 3.4, full daylight 10,000 to 25,000. A 0.0001 lux camera claims moonless starlight. Source: Make: Magazine.

Why two lux figures cannot be compared directly. Makers measure minimum illumination under different shutter speeds, gain limits, lenses, and definitions of a usable image, so treat a lux figure as a starting point, not a ranking. IRLAB states the rule: a lower published figure indicates a more sensitive camera, provided the figures are quoted under comparable conditions. Source: IRLAB.

Lux vs sensitivity in mV/lux-sec. Some makers state sensitivity in millivolts per lux-second instead of lux: RunCam lists the Phoenix 2 SP V5 at 13,000 mV/lux-sec and the Night Eagle 3 at 11,390 mV/Lux-sec. A sensitivity figure and a lux figure cannot be ranked against each other. Source: post 13426, citing the RunCam manuals via Manuals+.

The only lux figures you can quote. State a lux figure only where the manufacturer published it: the Caddx manual rates the Ratel 2 at 0.0001 lux, and the Foxeer manual rates the Cat 3 at 0.00001 lux. Every other camera here states “not published”.

Camera Sensor Min illumination Source of figure
CADDXFPV Ratel 2 1/1.8-inch starlight 0.0001 lux Caddx manual
Foxeer Cat 3 (reference, not stocked) 1/3-inch CMOS 0.00001 lux Foxeer manual
Foxeer Micro Toothless 3 1/2-inch CMOS starlight Not published Foxeer publishes none
RunCam Phoenix 2 Nite 1/2.8-inch 2MP starlight Not published RunCam publishes none

Starlight or IR: which technology fits your flying?

Starlight amplifies the visible light already there, so it works at dusk, under streetlights, and in moonlight, with no extra hardware. Its limit is total darkness: under a moonless overcast sky with no streetlights, even the best starlight sensor runs out of photons. IR adds light the human eye cannot see, from an illuminator the camera reads. Source: UAVMODEL; Oscar Liang.

IR: bring your own light. An IR illuminator shines near-infrared light, usually at 850nm or 940nm, onto the scene. Oscar Liang built his IR torch from a 48-LED board costing about 8 US dollars, wired to a 3S balance plug and mounted on a GoPro mount. High-power IR units run 5 to 15W and 30 to 60g. Source: Oscar Liang; UAVMODEL.

850nm vs 940nm. An 850nm illuminator emits a faint red glow and cameras see it well; a 940nm illuminator is completely invisible but slightly worse, and it needs a camera with no IR-cut filter. For most pilots 850nm is the practical pick. Source: UAVMODEL.

The IR-cut filter decides everything. A camera can only use IR light if no IR-cut filter sits in the light path. There are four filter designs, and they behave very differently at night.

Filter design How it works Night behavior Example
No IR-cut filter Nothing blocks IR Sees IR light at all times RunCam Phoenix 2 Nite
Removable filter Filter lifts out for night mode Color by day, IR night with filter out CADDXFPV Gazer
Switchable IR-cut (ICR) Filter moves out in the dark Color by day, black-and-white IR night Day/night security-style cameras
Fixed IR-cut filter Filter always in place True color by day, blind to IR at night Most standard day FPV cameras

The Phoenix 2 Nite has no IR-cut filter at all, which is why it is the darkest-flying analog camera in stock. A fixed-filter camera will not see an IR illuminator no matter how bright it is, so check the filter before you buy the light. Source: post 13426; Oscar Liang.

Which lens should a night FPV camera use?

The lens decides how much light reaches the sensor and how much of the scene you see.

Lens choice What it does Night pick
Focal length Sets the field of view; shorter is wider and shows obstacles earlier 2.1mm, 165-degree FOV on the Ratel 2; the Nite is narrower at up to 125 degrees
Aperture (F number) Sets how much light gets in; lower F passes more light F1.0 on the Gazer, widest of any stocked night camera
M12 swap Most micro cameras use M12 threaded lenses, so the lens is replaceable Fit a 2.1mm M12 lens for a wider night view; keep it clean, since a smudged lens scatters streetlight like fog
IR-corrected lens A normal lens focuses visible light and IR at different points, so a day-sharp image goes soft under IR The Cat 3 ships with a large-aperture night-vision lens, per the Foxeer manual

Source: post 13426; Oscar Liang; Make: Magazine; Foxeer Cat 3 manual.

How do you set up a night camera in the OSD?

Most analog night cameras are tuned through an on-screen display menu, reached with the camera joystick or the OSD cable. Change one setting at a time so you know which change fixed the image. Source: UAVMODEL; Oscar Liang; Make: Magazine.

Setting Day value Night value Why it changes
Shutter / exposure Auto, fast Auto, max 1/30s or 1/25s Slower shutter lets in more light
Gain / AGC Low or auto Maximum auto gain Gain brightens the image; the cost is noise
2D noise reduction Off or low Medium to high Cuts grain at the cost of slight softening
3D noise reduction Off On where the camera has it Combines frames to cut noise
WDR On Off or low WDR amplifies noise in dark areas
Day / Night mode Color Auto, or black-and-white Black-and-white drops color noise and improves contrast
White balance Auto Fixed value Auto white balance swings color between lit areas

Step 1: shutter and gain. Set shutter to auto with a maximum exposure of 1/30s or 1/25s. Set the maximum gain as high as the camera allows, often 60dB or more. Accept the grain. Source: UAVMODEL; Oscar Liang.

Step 2: noise reduction. Set 2D noise reduction to medium or high, and 3D noise reduction on. 3D noise reduction combines frames, which cuts noise but creates slight ghosting on fast motion. Source: UAVMODEL; Caddx spec sheet.

Step 3: WDR, white balance, and color. Turn WDR off or low at night: it amplifies noise in dark areas and creates artifacts that look like obstacles. Fix the white balance to one value. Switch Day/Night to auto or straight to black-and-white. Source: UAVMODEL; Oscar Liang.

Step 4: check the power feed. A noisy power feed shows up as rolling lines in the video. Feed the camera from a clean 5V pad or a separate BEC where you can, and keep the camera signal wire away from motor wires and the VTX antenna. Source: post 13426.

What light level are you actually flying in?

Light level Ambient light What works What fails
Dusk 10 to 100 lux Any starlight camera, color mode A small day sensor
Streetlit park 1 to 10 lux Starlight camera, WDR low, B/W optional A day camera with a fixed IR-cut filter
Full moon, clear sky 0.27 to 1.0 lux Starlight camera, high gain, noise reduction on A 0.01 lux day camera
Moonless, clear sky 0.002 lux Starlight at max gain, or IR Any camera that needs 0.01 lux or more
Moonless, overcast 0.0001 lux IR plus a filterless camera Starlight alone, with no ambient light
Total dark, indoors Near zero IR plus a filterless camera Every visible-light camera

Ambient figures from the Make: Magazine lux table. Each step down needs a more sensitive camera or added light. With streetlights, a starlight camera is enough.

How do sensor size, TVL, and latency fit together?

Spec What it means at night What to buy on
Sensor size Bigger gathers more light, so the image holds up longer as light fades 1/2-inch (Toothless 3) or 1/1.8-inch (Ratel 2, Gazer, Moonlight kit); the Nite is 1/2.8-inch but has no IR-cut filter
TVL Analog horizontal resolution; matters least at night 1200TVL on most stocked analog night cameras, 1500TVL on the Nite and Gazer
Latency Analog runs about 20 to 26 ms and degrades gracefully; digital is sharper but a weak signal freezes or breaks up Fly analog for the live feed, record digital for the footage

Source: post 13426; Oscar Liang; IRLAB.

What mistakes ruin a night camera image?

  • Buying on the lux figure alone. Check the sensor size and the test conditions too.
  • Fitting a day camera and hoping the settings save it. No OSD setting adds photons the sensor never collected.
  • Leaving the IR-cut filter in place and buying an IR light. A fixed-filter camera cannot see IR light.
  • Mounting the IR panel next to the lens. IR light in the lens creates glare. Mount the panel on top of the quad, away from the lens. Source: Oscar Liang.
  • Leaving WDR on at night. WDR amplifies noise and creates artifacts that look like obstacles.
  • Flying a new spot, or flying fast, at night. Recon in daylight first, then slow down and add 50 percent extra clearance to every gap. Source: UAVMODEL.
  • Skipping the strobe and the buzzer. The strobe keeps the quad legal and visible; a self-powered buzzer finds it in the dark.

How do you fix a night image that is dark, noisy, or washed out?

Most night image problems are settings or power, not a bad camera.

The image is dark even at dusk. Check that Day/Night is set to Auto and not locked to Day. If the camera has an IR-cut filter, the filter is blocking the light you need in near darkness. Check the shutter maximum: if it is capped at 1/120s, raise it to 1/30s.

The image is noisy and grainy. Turn 2D noise reduction to medium or high, and 3D noise reduction on where the camera has it. Switch to black-and-white mode, which drops the color noise.

The image is washed out around lights. Set WDR off or low at night. Angle the camera down so streetlights sit at the top of the frame. Check for a light shining into the lens, including your own strobe or IR panel mounted too close.

The video has rolling lines or interference. The camera power feed is noisy. Move the camera power to a filtered 5V pad or a separate BEC, and keep the camera signal wire away from motor wires and the VTX antenna.

The camera switches between color and black-and-white on its own. Day/Night set to Auto can hunt when the threshold sits in the middle of your light level. Lock it to black-and-white for the flight. Source: Oscar Liang.

Which night camera should you buy for your flying?

Buy for the light level you fly in. The full per-use picks are in the companion buying guide, How to Choose an FPV Camera for Night and Low-Light Flying.

Dusk and streetlit flying, one camera for everything. Buy the CADDXFPV Ratel 2 (ID 20161) at $68.99 sale, $82.99 regular: the only manufacturer-published 0.0001 lux rating in stock, a 1/1.8-inch starlight sensor, and a 165-degree view from the 2.1mm lens. If the budget is tight, buy the Caddx Ratel 2 V2 (ID 13206) at $44.99 instead: same sensor, resolution, lens, and voltage range. Note: the two listings are the same camera model; keeping both is Alex’s call.

After dark, or flying with IR. Buy the RunCam Phoenix 2 Nite (ID 20157) at $104.99 sale, $126.99 regular. No IR-cut filter, 1500TVL, and automatic color to black-and-white switching. It is the darkest-flying analog camera in stock.

Dusk freestyle where sensor size matters most. Buy the Foxeer Micro Toothless 3 (ID 20159) at $89.99 sale, $108.99 regular. Its 1/2-inch CMOS sensor is the largest sensor on any stocked analog camera here. Foxeer publishes no lux figure for it.

Reference only, not stocked. The Foxeer Cat 3 (0.00001 lux per the Foxeer manual) is not stocked at QRC.

Parts used in this guide

Prices and stock were verified live on qualityrcparts.com on 2026-11-21. All four items below are in stock and purchasable.

Shipped fast and securely from our secure facility in Queensbury, NY. QRC ships within the USA only.

Related guides

FAQ

What is a starlight FPV camera? A starlight FPV camera uses a large, sensitive CMOS sensor built to make a flyable image in very low light. “Starlight” is a marketing term, not a standard, so judge it by sensor size and manufacturer-published sensitivity. Source: UAVMODEL; Oscar Liang.

What lux rating do I need for night FPV flying? For dusk and streetlit flying, a camera rated at 0.0001 lux, like the Ratel 2 per the Caddx manual, holds a flyable image. For moonless dark with no streetlights, no lux rating is enough on its own: you need an IR illuminator plus a camera with no IR-cut filter. Source: Caddx manual.

Can I compare two cameras by their lux figures? Only if the figures were measured the same way, and they rarely are. Use the lux figure as a starting point, then check sensor size and filter type. Source: IRLAB.

What is the difference between starlight and IR night vision? Starlight amplifies the visible light already in the scene and needs some ambient light. IR adds near-infrared light from an illuminator, which an IR-sensitive camera reads and the human eye cannot see. Source: Oscar Liang; UAVMODEL.

Should I use 850nm or 940nm IR light for FPV? Use 850nm for most flying: cameras see it well. 940nm is completely invisible with no red glow, but performance is slightly worse, and it needs a camera with no IR-cut filter. Source: UAVMODEL.

What OSD settings should I change for night flying? Set the shutter to auto with a maximum of 1/30s, raise the gain limit to maximum, turn 2D and 3D noise reduction on, turn WDR off or low, fix the white balance, and switch to black-and-white mode. Source: UAVMODEL; Oscar Liang.

Sources

Last updated: 2026-11-21

Analog FPV Capture Guide: Record Video on PC and Phone

To record analog FPV video, feed your receiver output into a recorder and start it before takeoff. Three routes work: a USB capture adapter into a PC running OBS Studio, a DVR built into your goggles or a monitor, or a UVC app on a phone. The recording shows exactly what the receiver saw, static included, so fix the picture before you press record. Fly from your goggles, not from the recording screen.

How does analog FPV video reach a recorder?

Analog FPV video travels as a continuous composite video signal, not as digital data. The chain is short: the camera sends composite video to the video transmitter, the transmitter sends it over the air on the 5.8GHz band, a receiver on the bench picks it up, and the receiver hands composite video out of its RCA video socket. A recorder sits at the end of that chain and saves what the receiver outputs. If you have not got the signal into a computer yet, read the QRC conversion guide first: How to Convert Analog FPV Video to USB on a Computer. It covers the two routes in full, receiver plus USB capture adapter and UVC OTG receiver, with signal troubleshooting. Digital FPV systems (DJI, Walksnail, HDZero) do not use this chain: their video is a digital stream, not analog composite video, so this adapter does not work with them.

What are the three ways to record analog FPV video?

Pick the recorder by where you want the file and what you already own. All three record the same feed: what the receiver saw, including every breakup.

Route Where the file lands Best for Main limit
PC with USB capture adapter PC hard drive Best files to edit and share, streaming Needs a PC at the field or bench
Goggle or monitor DVR Micro SD card in the goggles or monitor Crash investigation, zero extra gear while flying Lower quality than PC capture, card not included
Phone with UVC receiver Phone storage Spectating, ride-along video, no PC QRC does not currently stock a UVC receiver

The PC route gives the cleanest editable files. The DVR route is the one most pilots actually use, because it needs nothing extra while flying.

What will the recording look like?

Analog FPV video is low resolution by modern standards, and every recorder here saves the received signal, not the camera’s original picture.

Resolution. The analog DVR guide at UAVModel notes most analog DVRs record at 30 frames per second, with bitrate typically locked between 6 and 12 Mbps, which is adequate for 640×480 or 720×576 resolution but breaks down with complex detail, rapid motion, or static interference. The QRC capture adapter listing states 720P USB video output, NTSC and PAL.

Static is recorded, not removed. The recording shows the same breakups you saw while flying. The QRC goggles guide puts it plainly: a DVR records exactly where the quad went down, and the recording is lower quality than an action camera and shows the same breakups you saw while flying. Clean footage of the flight itself needs an onboard recorder or an action camera on the quad.

Latency. The analog link itself adds effectively no processing delay, because the signal is a continuous waveform with no encode and decode step, A USB capture adapter and OBS add a processing step, so the PC screen lags behind the goggles. No latency number in milliseconds is stated here, because no primary source or named test was found to support one. Fly from the goggles, never from the recording screen.

Audio. Most analog FPV cameras send video only, so expect a silent file unless your camera has a microphone. The adapter passes audio through if the source carries it.

How do I record analog FPV video on a PC with a USB capture adapter?

This is the full OBS setup. It assumes the receiver is already locked onto the VTX channel and the picture is clean. Recording a bad signal only preserves it.

1. Connect the chain. Plug the receiver composite video output into the adapter RCA input, using the yellow plug for video. Plug the adapter into a USB port on the computer. The Media-Tech MT4169 video grabber manual advises using a USB port on the back of a desktop computer and avoiding front panel USB ports or hubs, because they can cause signal problems.

2. Check the computer sees the adapter, then add it in OBS Studio. On Windows, open the Camera app. On Mac, open Photo Booth or FaceTime and look for the adapter in the camera list. If nothing appears, try a different USB port and cable. OBS Studio is free, runs on Windows, Mac, and Linux, and is the program the MT4169 manual recommends. In the Sources panel, click the plus sign, select Video Capture Device, create a new source, and pick the adapter from the device list. If the feed does not appear in the OBS preview, check the Windows camera permission first: Settings, Privacy and Security, Camera. If your camera has a microphone, add an Audio Input Capture source in OBS and pick the adapter. If you hear nothing, check the Windows microphone permission at Settings, Privacy and Security, Microphone.

3. Set the recording output before you record. Open File, Settings, Output, Recording. Set the recording format to MKV, not MP4. The QuantumWarp analog capture guide recommends MKV, because if the computer crashes mid-recording, an MKV file is usually still playable, while an MP4 file is often lost. OBS can remux the finished MKV to MP4 afterwards under File, Remux Recordings. Set the recording path to a drive with free space, and record a short test clip first.

OBS setting What to pick Why
Recording format MKV Survives a crash mid-recording; remux to MP4 later
Recording path A drive with free space A full drive stops the recording
Encoder Hardware encoder if OBS offers one, otherwise software x264 Keeps the PC responsive while recording
Source One Video Capture Device, the adapter One source keeps the file clean
Test clip Record 30 seconds, play it back Confirms picture, format, and file location before the flight

4. Record. In the Controls panel, click Start Recording, then fly. Click Stop Recording before you power anything down. Keep the scene to the single capture source: anything on screen in OBS is burned into the recording and cannot be removed later.

How do I record with a DVR in goggles or on a monitor?

A DVR built into goggles or a monitor records the received feed onto a micro SD card. It is the simplest route because it needs no computer and no extra box, and it records exactly what you saw.

Start the DVR before takeoff. The QRC goggles guide notes that Oscar Liang starts the DVR before every takeoff for exactly this reason: the last seconds of the flight are the ones that show where the quad went down.

Use a fast card, and format it in the goggles. The UAVModel DVR guide advises a high-quality U3 or V30 rated micro SD card with at least 64GB capacity, formatted in the goggles before each session. The Eachine EV800D goggles stocked at QRC do not include a card in the box, so buy one separately.

Turn off the overlays that get burned into the file. If your goggles allow it, disable the on-screen recording timer and recording status indicator. The UAVModel guide is direct about why: these overlays are burned into the video and cannot be removed later.

Pick the file format if the menu offers one, and play it back in the goggles. The UAVModel guide advises setting the recording format to MOV rather than AVI when the goggles offer the choice, because MOV files handle dropped frames more gracefully. Most goggles with a DVR let you play the footage back inside the goggles, so you can watch the last seconds at the field and walk straight to the crash site. The stocked DVR units are in the Parts block below. The basic 4.3-inch monitor and the 3-inch micro monitor have no DVR, so they can show the feed but cannot record it.

How do I record analog FPV video on a phone?

The phone route uses a UVC receiver: a 5.8GHz receiver with a USB output built in, plugged straight into the phone. The phone treats it like a webcam, and the UVC app records the feed. The conversion guide states the key point in one line: a UVC receiver also works as a cheap DVR, because your phone records the feed. Use the app that came with the receiver first. If the app shows the feed but has no record button, use the phone screen recorder instead: an Instructables build from 2016 notes that the EasyCAP Viewer app did not record at the time, and the author captured the screen with a screen recorder. That workaround records whatever is on the phone screen, so keep notifications off. Quality RC Parts does not currently stock a UVC receiver, so buy one that lists UVC support for your phone. For the full phone setup, see Method 2 in the conversion guide linked above. iPhone support for UVC is thinner than Android, so check compatibility for your exact phone before you buy.

What do I do with the files after the flight?

Copy the files off the card or drive before you edit anything. Do not edit from the SD card: a card that is still in the goggles is easy to format by accident, and editing from it is slow.

Convert variable frame rate to constant frame rate before editing. The UAVModel guide notes that many goggle DVRs produce variable frame rate files that cause audio sync issues and stuttering in editing software, and advises converting to a constant frame rate with a tool like HandBrake in a single pass. Do this before you cut anything.

Clean up the picture lightly, and upscale before uploading. The UAVModel post-processing advice is a subtle sharpen filter at 0.3 to 0.5 strength, a slight contrast boost, and a saturation increase of 10 to 15 percent. Upscale analog DVR footage to 1080p when rendering for YouTube or social media, because the higher resolution forces the platform to use a better compression codec.

What are the common mistakes?

  • Starting the recorder after takeoff. The useful seconds are the last ones. Start the DVR or OBS recording before the quad leaves the ground.
  • Recording a weak link and blaming the recorder. Static in the file means static in the feed. Fix antennas, channel, and VTX power first.
  • Leaving the recording timer on screen. It is burned into the file and cannot be removed later.
  • Recording to MP4 in OBS. A crash mid-recording can lose the whole file. Record MKV and remux afterwards.
  • Forgetting the SD card. The EV800D does not include one. A DVR with no card records nothing.
  • Using a slow card. A card below U3 or V30 can drop frames or stop the recording. Format it in the goggles before the session.
  • Flying from the PC screen. The USB capture path lags behind the goggles. Watch and record on the PC, fly from the goggles.

How do I fix a recording problem?

OBS sees the adapter but shows no image. Check the Windows camera permission at Settings, Privacy and Security, Camera. Then check that the receiver is powered and on the right channel, and try a rear motherboard USB port instead of a front panel port or hub.

OBS shows the video but there is no sound. Check the Windows microphone permission at Settings, Privacy and Security, Microphone, then add an Audio Input Capture source for the adapter in OBS.

The recording stutters or drops frames. Close other programs, switch OBS to a hardware encoder if one is available, and record to a drive with free space. If the finished file stutters in an editor but plays fine in a player, convert it from variable frame rate to constant frame rate with HandBrake.

The DVR did not record. Check the card is in the goggles, has free space, and was formatted in the goggles. Check that you started the DVR before takeoff. A card that works in a computer does not always work in goggles.

The file will not play. Try VLC first, since it plays more formats than most players. If an OBS MKV file will not open in your editor, remux it to MP4 in OBS under File, Remux Recordings. If a DVR file will not open, try the MOV format next time.

The recording stops early. The card is full, too slow, or failing. Copy the files off, format the card in the goggles, and replace a card that keeps failing.

Which recording route should I pick?

Your goal Pick this route Why
Crash record while flying with goggles Goggle DVR Already there, playback in the goggles at the field
Best files to edit, share, or stream PC with USB capture adapter and OBS Record MKV, remux to MP4, convert frame rate before editing
Big shared screen at the field Monitor with a DVR A spotter sees the same feed, and the DVR records it
Spectate or record on a phone, no PC UVC receiver with a UVC app Simplest setup, but QRC does not currently stock a UVC receiver
Cleanest possible footage of the flight None of these All record the received feed. That needs an onboard recorder or an action camera on the quad
## Parts used in this guide

Prices and stock were verified live on qualityrcparts.com on 2026-11-21. All four items below are in stock and purchasable.

Shipped fast and securely from our secure facility in Queensbury, NY. QRC ships within the USA only.

Related guides

FAQ

Can I record analog FPV video on my PC? Yes. Connect the receiver composite video output to a USB video capture adapter, plug the adapter into the PC, add it as a Video Capture Device in OBS Studio, and press Start Recording. Source: Media-Tech MT4169 video grabber manual.

What resolution does a USB capture adapter record at? It records the analog signal it is given, not a fixed high resolution. The QRC adapter listing states 720P USB video output. The ivcan CVBS to USB converter lists 800×600 and 640×480 at 30 frames per second for its own device. Expect standard definition footage, not HD.

Do I need drivers for a USB video capture adapter? Usually no. The QRC adapter listing says its driver installs automatically when you plug it into a PC, and the MT4169 manual says Windows 10 and 11 detect this class of device automatically.

Can I use a USB video capture adapter for live streaming? Yes. OBS Studio records and streams from the same source, so the adapter feed can go to a stream as well as to a file. The ivcan converter FAQ lists live streaming as a supported use for this class of device.

Why does my DVR footage look worse than what I saw in the goggles? Analog DVRs compress video in real time with hardware encoders that prioritize low latency over image quality, and most record at 30 frames per second with bitrate locked between 6 and 12 Mbps. Source: UAVModel FPV goggle DVR guide.

What SD card should I use in a goggle DVR? A high-quality U3 or V30 rated micro SD card with at least 64GB capacity, formatted in the goggles before each session. Source: UAVModel FPV goggle DVR guide.

Can I record FPV video on my phone? Yes, with a UVC receiver and a UVC app: the phone records the feed, so the receiver works as a cheap DVR. If the app shows the feed but has no record button, use the phone screen recorder instead. Source: QRC conversion guide, Instructables EasyCAP build.

Why is there no sound in my recording? Most analog FPV cameras send video only, so a silent file is normal. If your camera has a microphone, check the Windows microphone permission and add an Audio Input Capture source for the adapter in OBS. Source: Media-Tech MT4169 video grabber manual.

Sources

Last updated: 2026-11-21

PETG vs ASA vs Nylon: Best Filament for RC Parts

PETG is the default pick for most RC and drone parts. ASA is the pick when the part lives outdoors in sun and weather. Nylon is the toughest of the three, and the hardest to print, so it belongs on high-load brackets, gears, and wear parts once you can keep it dry and enclosed. First functional part on an open-frame printer? Start with PETG. Part sits in sun all summer? Print it in ASA. Repeated load and failure is not an option? Nylon earns its extra work.

How to read the numbers in this guide

Datasheet figures vary by brand, grade, test method, and moisture state, so this guide does not mix brands into one table. The comparison table below is qualitative on purpose. Where a figure is given, it comes from one named manufacturer datasheet and describes a lab specimen printed at 100 percent infill, not your part. For PLA and PLA+ basics, read the PLA guide first: PLA vs PLA+ vs PETG: Pick the Right 3D Printer Filament for Drone Parts.

Is PETG good for RC and drone parts?

Yes. PETG is the easy engineering filament and the baseline for rigid drone and RC parts. It prints on most printers without an enclosure, flexes instead of snapping, and holds up better than PLA under knocks, heat, and water. The listing for the stocked PETG refill states impact resistance twice that of standard PLA, with enhanced chemical and water resistance. That figure comes from the live listing.

Heat: PETG handles more heat than PLA but less than ASA or nylon. Polymaker lists 69C and Bambu Lab lists 71C for its PETG Basic, both heat deflection at 0.45 MPa.

Strength: PETG is strong and a little flexible. It bends under load instead of cracking through, and its layers hold together better than any other common filament. CadFlow, using Polymaker datasheets, lists PETG at 48 MPa printed flat and 45.7 MPa printed upright, so it keeps about 95 percent of its strength across the layers.

Warping and enclosure: PETG warps little and needs no enclosure. Fumes: none special.

Settings: typical ranges across the Filwiz, Techietory, and ADP guides are nozzle 230 to 250C, bed 70 to 80C, fan 30 to 60 percent. Too much cooling weakens layer adhesion.

Weaknesses: PETG strings more than PLA, so tune retraction until the strings stop. It bonds hard to a bare bed, so use a release agent such as a glue stick on smooth PEI. Damp PETG prints rough and weak, so dry it at about 65C for 4 to 6 hours if you hear popping.

Is ASA good for RC and drone parts?

Yes, when the part lives outdoors. ASA is essentially ABS with UV resistance built in. It was developed to fix the weakness that kills ABS outside: yellowing and brittleness after sun exposure. If your part goes outdoors, ASA is the default choice, and every top guide agrees on that point.

Heat: ASA handles more heat than PETG by a clear margin. Polymaker lists 103C and Bambu Lab lists 100C for its ASA, both heat deflection at 0.45 MPa.

Strength: ASA is tough on impact and rigid enough for structural parts, but it is not stronger than PETG in a straight pull. Polymaker lists ASA at 43.8 MPa printed flat and 32 MPa printed upright, against PETG at 48 and 45.7 MPa. Pick ASA for sun and heat, not for raw tensile strength.

UV and weather: this is the reason ASA exists. It holds its color and structure under UV, where ABS yellows and turns brittle and PLA breaks down in direct sunlight over time. Use ASA for antenna mounts, drone housings, and RC car bodies.

Warping and enclosure: ASA warps significantly without an enclosure, and it is the number one ASA printing problem across the guides. It shrinks as it cools, so drafts cause warping and layer splitting. An enclosure is strongly recommended, with a warm chamber around 35 to 50C. A brim of 5 to 10 mm helps on large parts.

Fumes: ASA emits styrene fumes while printing, so ventilation is required, not optional. Print in a well-ventilated area or exhaust the fumes outside. A carbon filter is the minimum for ASA, per the Filwiz guide.

Settings: typical ranges across the Filwiz, Techietory, and ADP guides are nozzle 240 to 260C, bed 90 to 110C, fan 0 to 30 percent, print speed 40 to 80 mm per second.

Weaknesses: without an enclosure ASA warps and splits, and with too much fan it cracks between layers. It costs about a third more per spool than PETG, per the CadFlow price check.

Is nylon good for RC and drone parts?

Yes, for the hardest jobs, and only if you respect its moisture problem. Nylon, also called polyamide or PA, offers the best combination of tensile strength, impact resistance, and abrasion resistance of any common FDM filament. It bends instead of shattering, resists wear, and is slippery enough for gears, bushings, and living hinges. It is also the hardest of these three materials to print.

Heat: nylon handles more heat than PETG and about the same as ASA, with the exact figure depending on grade and annealing. Polymaker lists its nylon copolymer at 111C heat deflection after annealing, the highest of the six filaments CadFlow compared.

Strength: nylon is the strongest of the three in a straight pull and the toughest on impact. CadFlow lists 78 MPa printed flat and 45.8 MPa printed upright, only 59 percent of its flat strength across the layers. Orientation matters most for nylon: print a nylon hook lying down, not standing up.

Wear: nylon is the pick for parts that slide, rub, or hinge. Gears, hinges, bushings, snap-fit clips, wear plates, and living hinges are nylon jobs. A nylon part does not shatter. It bends, absorbs the hit, and returns to shape

Warping and enclosure: nylon warps severely without an enclosure. An enclosure is required, with a warm chamber around 45 to 65C, and a large brim plus a Garolite bed surface helps adhesion.

Moisture: this is the nylon problem that decides everything else. Nylon absorbs moisture from the air fast, and wet nylon prints with popping, stringing, rough surfaces, and weak layer bonds. Filwiz cites up to 9.5 percent moisture by weight for PA6 and Prusa lists up to 10 percent, while CadFlow cites 2.82 percent for Polymaker PolyMide CoPA. Dry it at 70 to 80C for 6 to 12 hours before printing, and print from a dry box if possible.

Settings: typical ranges across the Filwiz, Techietory, and ADP guides are nozzle 240 to 290C depending on grade, bed 70 to 90C, fan 0 to 30 percent, print speed 30 to 60 mm per second. Filled nylon needs a hardened steel nozzle.

Weaknesses: wet filament, no enclosure, and wrong orientation are the three killers. Upright orientation throws away nearly half its strength.

How do PETG, ASA, and nylon compare side by side?

Property PETG ASA Nylon (PA6 / PA12)
Easiest to print Easiest of the three Moderate, needs enclosure Hardest of the three
Heat resistance Moderate, better than PLA High, best for sun and hot cars High, best after annealing
Strength in a straight pull Strong Strong, slightly below PETG Strongest of the three
Strength across the layers Best, about 95 percent of flat strength Weaker, about 73 percent of flat strength Weakest, about 59 percent of flat strength
Impact resistance Good, flexes instead of snapping Good, tougher than PLA on a notched test Excellent, bends and returns to shape
Stiffness Stiff with a little give Rigid Stiff, more flexible in thin layers
UV and weather resistance Moderate Excellent Poor
Warping Low to moderate Moderate to high High
Moisture sensitivity Moderate Low Very high
Chemical resistance Good Good Excellent
Wear resistance Fair Fair Excellent, best for gears and hinges
Enclosure needed No, optional Recommended, near required Required
Ventilation needed No Yes, styrene fumes Good practice
Typical price per kilogram Lowest of the three Middle Highest of the three

Nylon wins flat by a wide margin and loses the most upright. PETG barely loses strength across the layers, so a PETG hook printed upright still holds while a nylon hook printed upright can snap. Turn the part so the main load runs along the layers. Heat figures agree on the order and disagree on the digits across brands, so use the order, not the digits.

Which filament wins for each drone and RC part?

Small frames, whoop frames, and prop guards. PETG first. It is the safest first plastic for a small frame, per the DroneTrader guide, and the default for whoop frames and prop guards, per the Prusa Knowledge Base summary in that guide. For larger builds, DroneTrader recommends a molded carbon kit for frame arms.

Mounts, brackets, and standoffs. PETG for rigid mounts indoors or in shade, ASA for mounts in sun. For a high-load bracket, nylon is the pick, but only after your own validation, per the ADP guide.

Outdoor parts, canopies, and housings. ASA, without a close second. Anything that lives outside, sits on a car dashboard, or flies in direct sun all summer belongs in ASA: antenna mounts, camera housings, field boxes, RC car bodies, and garden and automotive exterior parts. PETG ages faster in sun, PLA breaks down in sun, and nylon has poor UV resistance.

High-heat parts, motor mounts, and enclosures. ASA first, nylon second, and the stocked HT-PLA Pro as the easy option. Parts near motors and hot electronics need heat resistance PETG does not have. HT-PLA Pro prints like PLA with no enclosure and anneals at 100C for 30 minutes for its best heat resistance.

Gears, hinges, bushings, and wear parts. Nylon, and nothing else in this comparison. Its abrasion resistance and slipperiness are why gears, hinges, and living hinges are nylon jobs in every guide.

RC car and truck parts. PETG for brackets, chassis pieces, and guards that take hits. ASA for bodies and exterior parts in sun. Nylon for gears and suspension parts that wear.

What not to print. Print the parts that hold things. Buy the parts that spin or carry current. No filament here replaces a motor, a speed controller, a flight controller, a battery, or a propeller. Printed propellers are not a safe substitute for molded props. Bench-test every printed structural part with the propellers off, and check it for cracks after every hard landing.

What mistakes should you avoid?

  • Jumping straight to nylon. Do not skip PETG and jump straight to nylon. The skills you build dialing in PETG transfer directly to the harder materials.
  • Printing ASA without an enclosure or ventilation. ASA without an enclosure warps and splits, and without ventilation it fills the room with styrene fumes. Get the enclosure and the airflow first.
  • Printing nylon wet. Wet nylon is the most common nylon failure. If you hear popping or see rough surfaces and weak layer bonds, the filament is wet. Dry it and print from a dry box. A strong material printed wet can end up weaker than dry PETG, per the 3DX guide.
  • Buying on the flat tensile number alone. It is the most flattering value on the datasheet. For printed parts, the across-layer strength and the heat deflection figure usually decide whether a part survives, per the 3DX guide.
  • Comparing brands’ datasheets directly. Test settings differ, so compare materials within one brand’s sheets, per the 3DX guide.
  • Ignoring orientation. A part printed standing up, with the load pulling its layers apart, can snap where the same part printed lying down would hold. Think about the crash direction before you slice.
  • Assuming carbon fiber means tougher. Fibers add stiffness, not toughness, and they wear brass nozzles, per the 3DX guide.
  • Skipping the test fit. Print a fit check in PLA or PLA+ before committing to a long ASA or nylon print. A fit check that fails costs minutes instead of hours.

Why is my print failing?

Problem Likely cause Fix
Warping, corners lifting Cold bed, drafts, no enclosure Raise the bed temperature, add a 5 to 10 mm brim, close the enclosure.
Layer splitting or cracking Too much cooling, low nozzle temperature, cold chamber Reduce the fan to near zero for ASA and nylon, raise the nozzle temperature 5 to 10C, keep the enclosure warm.
Stringing Wet filament, high temperature Dry the spool, lower the temperature, tune retraction.
Popping, bubbles, rough surfaces Moisture in the filament Dry the spool fully. For nylon, dry 70 to 80C for 6 to 12 hours and print from a dry box.
Poor bed adhesion Dirty bed, wrong bed temperature, wrong surface Clean the bed with isopropyl alcohol, re-level, use glue stick on smooth PEI. Nylon usually needs Garolite or PVA glue.
Part snaps along a layer line Load across the layers, weak layer bonding Reorient the part so the load runs along the layers, reduce the fan, add walls.
ASA part smells and the room feels stuffy Styrene fumes, no ventilation Stop the print, ventilate the room, and do not print ASA again without a carbon filter.
Nylon part warps on a large flat print No enclosure, damp filament, wrong bed surface Enclose the printer, dry the filament, use a large brim and a Garolite bed surface.

Which filament should you buy?

First functional part, open-frame printer, most RC and drone parts. Buy PETG. It prints without an enclosure, flexes instead of snapping, and covers guards, brackets, chassis pieces, and mounts. The stocked PETG refill is the Anycubic PETG Filament Refill, 1.75mm, 1KG (ID 17689) at $18.99. It is a refill coil only with no spool included, so you need a reusable spool.

Part that lives outdoors, sits in sun, or sits in a hot car. Buy ASA. No ASA filament is stocked at the time of writing, so there is no ASA product link in this guide. Buy ASA from a filament maker whose datasheet you have read, and print it enclosed and ventilated.

High-load bracket, gear, hinge, or wear part, and you own an enclosure and a dryer. Buy nylon. No nylon filament is stocked at the time of writing, so there is no nylon product link in this guide. Buy the grade that matches the job, PA6 for strength, PA12 for lower moisture absorption, and dry it before every print.

Hot spot near a motor or electronics, and you want the easy option. Buy HT-PLA Pro. The stocked Polymaker HT-PLA Pro Filament, 1.75mm, 1KG (ID 17644) is $29.99. It prints like PLA with no enclosed chamber and anneals at 100C for 30 minutes for its best heat resistance.

FAQ

Which filament is strongest, PETG, ASA, or nylon? Nylon is the strongest common FDM filament overall, especially in carbon fiber filled form. On an open-frame printer, PETG is the strongest practical pick, because it needs no enclosure. Source: Techietory FAQ section, 3DX FAQ section.

Is ASA better than PETG for outdoor parts? Yes. ASA resists UV light and weathering far better than PETG, so it keeps its color and structure outdoors while PETG ages faster in sun. PETG is easier to print and stronger across the layers, so use PETG indoors and ASA outside. Source: Techietory FAQ section, Filwiz material comparison.

Do I need an enclosure to print ASA or nylon? Yes, for reliable results. An enclosure holds a stable chamber temperature of roughly 40 to 60C, which reduces warping and layer splitting. ASA warps significantly without one, and nylon warps severely without one. PETG prints fine without one. Source: Techietory FAQ section, Filwiz enclosure guide.

Can I print nylon without drying it first? No. Nylon absorbs moisture from the air within hours, and wet nylon prints with bubbles, rough surfaces, and weak layer bonds. Dry it at 70 to 80C for 8 to 12 hours before printing, store it sealed with desiccant, and print from a dry box when possible. Source: Techietory nylon section, Filwiz nylon section.

Which filament should I use for a drone frame? PETG for a small frame, such as a whoop. ASA for a frame or canopy that lives outdoors in sun. Nylon or carbon fiber nylon only for high-load prototypes, and only after your own validation. For frame arms on a large build, a molded carbon kit is the safer buy. Source: ADP quick reference, DroneTrader component matrix.

Is PETG stronger than PLA? PETG is tougher, more heat resistant, and more chemically resistant than PLA, and it flexes instead of shattering. PLA is stiffer and better for visual models. In Bambu Lab datasheet figures, PETG Basic beats PLA Basic on tensile strength, impact strength, and heat resistance, but other brands publish different numbers. Source: Techietory FAQ section, 3DX FAQ section.

Can you print an entire drone? No. You can print the frame, mounts, prop guards, and battery holders, but motors, flight controllers, speed controllers, batteries, and propellers must be bought. Printed parts hold things; they do not spin or carry current. Source: DroneTrader FAQ section.

Parts used in this guide

Prices and stock were verified live on qualityrcparts.com on 2026-11-21. Both items below are in stock and purchasable. No ASA filament and no nylon filament is stocked at the time of writing: a store search for “asa” returns 0 products, a store search for “nylon filament” returns 0 products, and a store search for “filament” returns 9 products, none of them ASA or nylon filament. The nylon search results are hardware, such as nylon screws, standoffs, propellers, and hinges, not filament. No ASA or nylon product is linked because none exists.

  • Anycubic PETG Filament Refill, 1.75mm, 1KG (ID 17689) – $18.99. Refill coil only, no spool included. Impact resistance twice that of standard PLA per the listing, 1.75mm diameter, 1KG. The PETG pick in this guide.
  • Polymaker HT-PLA Pro Filament, 1.75mm, 1KG (ID 17644) – $29.99. Full 1KG spool. Prints like PLA with no enclosed chamber and no hardened nozzle needed, anneals at 100C for 30 minutes for its best heat resistance. The stocked heat-resistant option for hot spots in this guide.

Shipped fast and securely from our secure facility in Queensbury, NY. QRC ships within the USA only.

Related guides

Sources

Last updated: 2026-11-21

LiPo Battery Straps: How to Mount a LiPo Battery

A LiPo battery strap holds the pack to the model so it cannot shift, slide, or come off in flight. On most FPV quads that means one or two straps around the pack and the frame, with a grip pad or hook-and-loop patch under the pack to stop sideways movement. On a plane or a car it usually means a strap around the pack and its tray or plate. Too short will not close, too loose lets the pack move and change the balance, and too tight can dent a soft case pack. Measure the loop, pick the strap to fit it, and shake-test the mount before you fly.

Why does battery mounting matter?

A loose battery is a safety problem first and a handling problem second. A pack that shifts moves the center of gravity, so the model handles differently from one minute to the next. A pack that comes off in a crash can take out a prop, and a flailing lead can damage electronics. A pack that slides sideways can rub its wrapper against a sharp frame edge until the wrapper wears through. The WildAir drone battery mounting guide puts it plainly: how you secure the battery matters more than many pilots realize, and a battery that comes loose can cause power loss or damage from flailing leads. Check the mount before every flight and after any crash.

What types of LiPo battery straps are there?

Five strap types cover nearly every RC job. No stocked listing publishes a load rating, so this guide states none. Pick by width, length, grip, and closing method.

Strap type How it holds Grip Best for
Rubberized hook-and-loop strap Hook-and-loop, rubberized grip coating High Most quads, planes, helicopters, and cars
Kevlar stitched strap with metal buckle Metal D-ring buckle cinches tight High FPV racing and long-range quads
Plain hook-and-loop strap Hook-and-loop, no grip coating Moderate Light packs, small models, general gear
Adhesive-back hook-and-loop strap Sticks to a flat surface, mates with a patch High on the stuck side Fuselage, tray, canopy
Elastic hook-and-loop strap Stretches, then pulls tight Moderate to high An extra-tight hold where a pack changes size slightly with temperature

The rubberized coating collects dirt, so replace the strap when grip fades. Keep a metal buckle clear of the battery leads and balance plug. A plain strap can slip on a smooth pack, so pair it with a grip pad or a hook-and-loop patch. The WildAir guide also rates silicone-backed straps as the best grip for racing and freestyle, but the store does not stock one at the time of writing, so none is listed in the Parts block below.

What size strap do I need?

Size a strap by the loop it closes around, not by the battery alone. The loop goes around the pack and the plate or tray under it. Measure it with a piece of string run around the pack and plate, then add overlap for the hook-and-loop to grip. Ufine recommends 20 to 30 percent adjustment margin, so a strap that only just closes with no overlap left is too short.

Worked example: the 3S LiPo Battery, 2200mAh, 50C, 11.1V, T Connector (ID 18815) measures 105 x 33 x 20 mm and weighs 179 g. Strapped across its 33 mm width, the loop around the pack and plate is roughly 2 times (33 + 20) plus the plate, about 110 to 120 mm before overlap, so a 200 mm strap closes it with plenty of overlap left. That matches listing 18973, which states it fits most 3S and 4S LiPo packs.

Wider straps spread the load and grip better. WildAir recommends 20 mm straps for most builds, 25 to 30 mm for larger batteries, and 15 to 20 mm for smaller builds. The Kevlar listing (ID 13602) agrees: 20 mm suits larger packs, 10 and 13.5 mm suit smaller builds.

Pack or model Strap width to start with Strap length to start with
1S to 2S whoop or micro pack 10 to 13.5 mm 130 to 160 mm
3S to 4S 1300 to 2200mAh pack, 5-inch quad 20 mm 200 mm
4S to 6S 1300 to 1800mAh pack, freestyle or racing 20 mm, two straps 200 to 260 mm
6S large pack, long-range quad 20 mm, two straps 260 mm
Plane or car pack on a tray 20 mm, or 1 inch (25.4 mm) hook-and-loop Measure the tray loop, then add overlap

Which strap is right for which model?

5-inch freestyle or racing quad. Two 20 mm rubberized straps, one near each end. Two straps stop the pack pivoting and give you a spare hold if one fails. WildAir recommends two 20 mm straps over a single 30 mm strap.

Long-range quad. Two 20 mm Kevlar straps, 20 x 260 mm if the pack is large.

Whoop, micro, or 3-inch quad. One narrow strap, 10 to 13.5 mm, is usually enough. A 20 mm strap on a tiny frame adds weight and slows battery changes.

RC plane. A strap around the pack and a mounting plate inside the fuselage, with a hook-and-loop patch between pack and plate so you can slide the pack to set the balance point. The RC Universe pattern-plane thread describes exactly this setup: two small hook-and-loop pieces on the pack mating with strips on a fixed plate, plus two outer straps holding the pack down.

RC car or truck. A strap around the pack and the battery tray, with a hook-and-loop patch under the pack if the tray is flat. Cars take hard landings and side loads, so check the strap after every run.

What are the mounting methods?

Parallel straps. Two straps running parallel, one near each end of the pack, spreading the pressure and making battery changes easy.

Cross straps. Two straps in an X pattern across the pack. This gives the most security and stops movement in every direction, at the cost of slower battery changes. Use it for racing and aggressive freestyle.

Loop-through. The strap threads through slots or cutouts in the frame itself, so it cannot slide along the frame. This needs a frame with strap slots, so check your frame before you buy straps for this method.

Tray and strap. The pack sits in a tray or on a plate, and the strap holds it down. The tray stops sideways movement and the strap stops lift. This is the standard method for planes and cars, and it works on quads with a battery plate.

Pad and strap. A grip pad, foam pad, or hook-and-loop patch sits under the pack, and the strap holds it down. The pad supplies friction and the strap supplies clamping force. Do not rely on a pad alone, and do not rely on hook-and-loop alone: WildAir warns that hook-and-loop by itself can fail during aggressive maneuvers, and the Flite Test thread reports a pack sliding out of its own heat shrink in a head-on crash when only hook-and-loop held it.

How do you mount a LiPo on a quad? Step by step

  1. Put a grip pad or a hook-and-loop patch on the frame plate where the pack will sit. If the frame has strap slots, thread both straps through them now.
  2. Set the pack on the plate where it balances the quad. Start centered, then slide it slightly forward or back to adjust the feel.
  3. Route the first strap around the pack and plate near the front end. Pull it snug and press the tail down flat, clear of the prop line.
  4. Route the second strap the same way near the rear end. Pull it snug and press the tail down flat.
  5. Push the pack sideways and try to slide it forward and back. It should not move. If it slides, tighten the straps first, then add a pad.
  6. Hold the quad and shake it firmly in every direction, then upside down. This is the WildAir shake test: if the battery moves at all, the mount needs work before you fly.

How do you mount a LiPo in a plane or a car? Step by step

  1. Fix a mounting plate or tray in the fuselage or chassis where the pack will sit. In a plane, glue or screw a plywood plate across the fuselage formers so it cannot move. In a car, use the tray the chassis provides.
  2. Stick a hook-and-loop patch on the plate and the matching patch on the pack, so you can slide the pack to set the balance point.
  3. Run one strap around the pack and the plate or tray, and pull it snug. On a longer pack, run a second strap near the other end.
  4. Set the balance point with the pack strapped in. Move the pack, not the plate, until the model balances, then re-check the straps: moving the pack can slacken a strap.
  5. Check that the strap does not press on the battery lead or the balance plug, and that the lead cannot reach a prop or a moving part. Shake the model firmly before you fly or drive. If the pack moves, tighten the straps or add a second one.

Where should the battery sit?

Battery position sets the balance, and balance sets how the model flies. Too far forward makes the model nose-heavy and fast in forward flight. Too far back makes it tail-heavy and quick to pitch. WildAir recommends a centered pack for freestyle and general flying, and a slightly forward pack for racing and long-range cruising. For a plane, set the pack so the model balances at the point the instructions give, and mark the plate so the next pack goes in the same place. For a car, center the pack in the tray so the weight is even side to side. The battery lead must reach the plug without strain or crossing a prop, and the balance plug must be reachable without removing straps.

What are the common mistakes?

  • One strap where two are needed. A single strap lets the pack pivot around it. Two straps, one near each end, stop the pivot and give you a spare hold if one fails.
  • Strapping too loose. A strap you can slide a finger under easily is too loose. The WildAir guide says the strap should be tight enough that the battery cannot move under moderate force, but not so tight that it deforms the pack.
  • Strapping too tight. A soft case LiPo dents under too much pressure. Tighten until the pack cannot move, then stop.
  • Relying on hook-and-loop alone. A hook-and-loop patch holds the pack from sliding, but it does not hold it down in a crash or in negative G flight. Always pair it with a strap.
  • Letting the strap tail stick up. A loose strap tail can catch a prop. Press the tail down flat every time.
  • Running the strap over the balance plug or the lead. A strap pressing on a plug can unplug it or chafe the wires. Route the strap clear of every wire.
  • Using a worn strap. A strap with frayed edges, a stretched hook-and-loop section, or a buckle that no longer cinches is a failed strap. WildAir reports losing a drone to worn straps that let the battery shift in a flip. Replace a strap at the first sign of wear, not after it fails.

How do you fix a battery that keeps moving?

The pack slides forward and back. Add a hook-and-loop patch or a grip pad under the pack, and move the straps closer to the ends. A strap in the middle of a long pack does not stop the ends from sliding.

The pack slides sideways. The pad is missing or worn, or the strap is too narrow for the pack. Add a grip pad or step up to a wider strap. On a quad, check the straps run through the frame slots.

The pack lifts off the plate in flips or hard turns. Add a second strap or switch to the cross-strap pattern. One strap cannot hold a heavy pack down in negative G flight.

The pack comes off in a crash but the straps look fine. That can be the mount working as designed: a strap that releases in a hard crash lets the pack carry its own energy away instead of tearing the frame apart. If the pack comes off in normal flight, the mount is wrong.

Which strap should you buy?

5-inch freestyle or racing quad, 3S to 6S packs. Buy the LiPo Battery Straps, Rubberized Non-Slip, 20 x 200mm, 5-Pack (ID 18973) at $13.99 on sale, $16.99 regular. The 200 mm length fits most 3S and 4S packs per the listing. Run two per pack; five in the pack means spares.

Long-range quad or heavy pack, or flying where a crash is likely. Buy the Kevlar Battery Straps, 2-Pack, Metal Buckle (ID 13602) at $8.99 to $9.49 depending on size. Pick the size to fit your loop: 10 x 130 mm and 13.5 x 160 mm for small builds, 13.5 x 200 mm and 18 x 210 mm for mid-size packs, 20 x 260 mm for larger packs.

Plane or car on a tray, or general gear strapping. Buy the Hook and Loop Fastener Strap 14in x 1in (ID 192) at $6.99. The 14 inch length and 1 inch width suit tray loops and longer packs, and the 10-pack gives you field spares. Post 16874 lists every size, from 6 inches to 14 inches.

First build, not sure what you need. Buy the rubberized 20 x 200 mm 5-pack (ID 18973) at $13.99 on sale. It fits the most common packs and grips without a pad. Measure your loop first: if your pack loop is longer than about 150 mm after overlap, step up to the 20 x 260 mm Kevlar size instead.

Parts used in this guide

Prices and stock were verified live on qualityrcparts.com on 2026-11-21. All four items below are in stock and purchasable. No strap listing publishes a load rating, so none is stated here.

Shipped fast and securely from our secure facility in Queensbury, NY. QRC ships within the USA only.

Related guides

FAQ

How tight should a LiPo battery strap be? Tight enough that the battery cannot move under moderate force, but not so tight that it deforms the pack. You should be able to slide a finger under the strap with firm pressure. Source: WildAir drone battery mounting guide FAQ.

Is one battery strap enough, or do I need two? Two straps are almost always better than one, even if the single strap is thicker. Two stop the pack pivoting and give you a spare hold if one fails. Source: WildAir drone battery mounting guide FAQ.

How do I know if my battery mounting is secure enough? With the model powered off, shake it firmly in all directions, then upside down. If the battery moves at all, the mount needs work. Source: WildAir drone battery mounting guide FAQ.

What size battery strap do I need for a 5-inch FPV quad? A 20 mm wide strap about 200 mm long, used two at a time, fits most 3S and 4S packs on a 5-inch frame. Measure your loop with a piece of string around the pack and plate, then add overlap for the hook-and-loop to grip. Source: WildAir strap width guidance, Ufine length margin guidance, and QRC listing 18973.

Can I use Velcro alone to hold a LiPo battery? A hook-and-loop patch stops the pack sliding, but do not rely on it alone. It does not hold the pack down in a crash or in negative G flight. Pair it with at least one strap. Source: WildAir drone battery mounting guide, Flite Test forum thread.

How do I mount a LiPo battery in an RC plane? Fix a mounting plate in the fuselage, stick a hook-and-loop patch on the plate and the pack so you can slide the pack to set the balance point, then run one or two straps around the pack and plate and pull them snug. Check the balance with the pack strapped in, then shake the model before you fly. Source: RC Universe pattern-plane thread, Model Flying forum thread.

Sources

Last updated: 2026-11-21