Maker Supplies: Microcontrollers, Sensors, and Prototyping Parts
Maker supplies are the parts behind every bench project: a microcontroller board, sensors, a display, power, and the wire and hardware that tie them together. This page gathers the maker shelves at Quality RC Parts, from ESP32 and Arduino-compatible boards to sensor modules, displays, and prototyping parts. Shipped fast and securely from our secure facility in New York, providing fast, high quality USA shipping.
Pick a board: ESP32, Arduino-compatible, Pico, STM32
Board choice sets what a project can do. Arduino-compatible boards are the easiest start, with the widest example libraries and simple 5V wiring. ESP32 boards add WiFi and Bluetooth plus more pins and speed, which suits camera projects, remote control, and connected builds. Raspberry Pi Pico and RP2040 boards are tiny, low cost, and precise on timing. STM32 boards offer more performance for builders past the beginner stage. Use the decision tables in Microcontroller Picker: Tables for ESP32, Arduino, Pico to match a board to a job, or start with How to Start with a UNO R3 Board for Arduino Projects and How to Choose ESP32 Development Boards for Your Build.
| Board family | Best for | Watch out for |
|---|---|---|
| Arduino-compatible | First projects, sensors, motors, learning | No built in WiFi on classic boards |
| ESP32 / ESP8266 | WiFi projects, cameras, remote control, more pins | 3.3V logic: check sensor voltage before wiring |
| Raspberry Pi Pico / RP2040 | Small builds, precise timing, USB projects | Smaller example library than Arduino classic |
| STM32 | Performance builds, precise control | Steeper setup than Arduino-compatible boards |
Sensors and displays
Sensors turn a board into a device that reacts. Distance sensors measure range, temperature and humidity sensors feed monitors, gas sensors feed alarms, and joysticks feed manual control. Displays close the loop: a small OLED shows readings without a computer attached. Check three things before ordering a sensor: supply voltage, output type (analog, digital, or I2C), and pin count. How to Use a 0.96 Inch SSD1306 OLED Display covers the most common starter display, and How to Choose the Right Sensors for Robotics Builds compares sensors by job. Shop the shelves: Sensor Modules, Robot Sensors, and Displays & Screens.
Power: the part beginners get wrong
A board on USB power runs code fine. Add motors, servos, or a bright display and the same supply browns out. Power hungry parts from their own battery or BEC, keep logic power steady, and share a ground. Charging modules such as the TP4056 handle single cell LiPo and Li-ion charging for small portable builds. Read How to Power an ESP32 Arduino Robot With a Battery and BEC and TP4056 Charging Module: LiPo and Li-ion Basics Guide before wiring power. Power shelves: Power Distribution & BECs and Batteries & Chargers.
Prototyping: wire it, test it, then make it permanent
Prototype on a breadboard with jumper wires so mistakes cost minutes, not a soldered board. Once the circuit works, move it to solderable perfboard or a PCB, add connectors for the parts you will swap, and use heat shrink and proper strain relief on every wire that moves. Soldering skill decides how long a build lasts: a cold joint fails under vibration. Start with Soldering Iron for Beginners: Your First Iron and How to Choose Solder Wire and Flux for RC Electronics. Shelves: Tools & Soldering, Connectors & Wiring, and Parts & Hardware.
A first maker project, in order
- Pick a board: UNO R3 compatible for the simplest start, ESP32 for wireless or camera work.
- Add one sensor and one output: a temperature sensor plus an OLED display, or a distance sensor plus a buzzer.
- Wire it on a breadboard and get readings on screen before adding anything else.
- Add power planning: battery and BEC or charging module if the build leaves the bench.
- Move the working circuit to a permanent board, add connectors, and mount it in an enclosure or chassis.
Maker guides for every stage
- Microcontrollers for Beginners: Makers Over 50: a gentle start with no assumed background.
- How to Start with RP2040 Boards for Tiny Maker Projects: small boards for small builds.
- Microcontroller Picker: decision tables for ESP32, Arduino, and Pico.
- Robot Starter Kit Shopping List: a full first order with checks.
- Drone Guides hub: the full guide list, including maker, sensor, and power guides.
Shop maker supplies by shelf
- Microcontrollers & Development: the full maker shelf.
- ESP32 & ESP8266: WiFi and Bluetooth boards.
- Arduino-Compatible Boards: UNO, Nano, and compatible boards.
- Raspberry Pi & Pico: Pico, Pico WH, and RP2040 boards.
- Sensor Modules: sensor modules for every job.
- Displays & Screens: OLED and TFT displays.
- STM32 Development Boards: STM32 boards.
Frequently asked questions
What do I need to start with microcontrollers?
A board, a USB cable, a breadboard, jumper wires, one sensor, and one output such as an LED or display. Start with one sensor and one output before adding more.
ESP32 or Arduino-compatible board for a beginner?
Arduino-compatible for the simplest start. ESP32 when the project needs WiFi, Bluetooth, a camera, or more pins. See the Microcontroller Picker.
Can I power a project from USB?
For the board and small sensors, yes. Motors, servos, and bright displays need their own battery or BEC supply. See How to Power an ESP32 Arduino Robot.
Not sure a part fits your project?
Ask a tech before you order and include your board and what you are building.
Shop the maker shelves
Product rows from the shelves on this page. The rows shuffle, so each visit shows a different mix.
Boards
-

ESP8266 ESP-07 Remote Serial Port WiFi Transceiver, AP+STA, 2-Pack
$12.99 Add to cart -

Raspberry Pi 4 Aluminum Armor Case with Dual Cooling Fan and Heatsinks (Board Not Included)
Sale! Original price was: $23.99.$19.99Current price is: $19.99. Add to cart -

ESP32-S3 N16R8 Development Board, Type-C, WiFi + Bluetooth, Single
Sale! Original price was: $15.99.$12.99Current price is: $12.99. Add to cart
Sensors and displays
-

Infrared Flame Sensor Module, 760nm to 1100nm, 3.3V to 5V
$4.49 Add to cart -

TCRT5000 Mini IR Reflective Sensor Module, 3-Pin, Analog + Digital, 10-Pack
Sale! Original price was: $9.99.$7.99Current price is: $7.99. Add to cart -

1.8 Inch SPI TFT LCD Display Module, 128×160 ST7735 with SD Card Slot for Arduino ESP32
Sale! Original price was: $13.99.$10.99Current price is: $10.99. Add to cart -

4.0 Inch SPI TFT LCD Touch Display Module, 480×320, ST7796S Driver
Sale! Original price was: $35.99.$29.99Current price is: $29.99. Add to cart
Tools and power
-

RC Driver and Wrench Kit, 9-Piece
$29.99 Add to cart -

RC Hex Bit Set, 5-Pack, 1.27/1.5/2.0/2.5/3.0mm, S2 Steel, 1/4 Inch Hex Shank for Power Drivers
Sale! Original price was: $16.99.$13.99Current price is: $13.99. Add to cart -

Syringe Epoxy Adhesive, 5-Minute Cure, 3.4oz
$9.99 Add to cart -

Thin Foam Safe Glue, 40ml
$6.99 Add to cart
Building a robot? See Build a Robot. Power questions? See Power and Charging. Guides live on the Drone Guides hub.

