Night FPV Cameras: Starlight, IR, and Low-Light Picks

A night FPV camera is not a day camera with the brightness turned up. It is a different sensor, a different filter, and a different set of settings. Pick the sensor first, check whether the camera can see infrared light, fit a fast wide lens, and set the OSD. The buying picks live in the companion guide linked below.

How does a starlight sensor see in the dark?

A starlight sensor is a CMOS sensor built to convert very few photons into a usable image. It is the first of three things that make a night camera different from a day camera. The name starlight is a marketing term, not a standard, so judge the sensor by its size, its pixel design, and its published sensitivity.

Back-illuminated pixels. In a back-illuminated sensor the light-sensitive area faces the lens directly, with the wiring behind it, so more of each pixel collects light. Starlight sensors in this class commonly use back-illuminated designs such as Sony STARVIS, named by UAVMODEL for the Ratel 2 and the Cat 3. Source: UAVMODEL.

Pixel size beats pixel count. A sensor with fewer, larger pixels collects more light per pixel, so a 1200TVL starlight camera can out-see a higher-resolution day camera at dusk. Source: Oscar Liang; IRLAB.

Gain, noise, and color. Night flying often pushes gain to 60dB or more. Oscar Liang notes that a good starlight sensor at 60dB of gain looks cleaner than a budget sensor at 40dB, and the Ratel 2 publishes a signal-to-noise ratio of 60dB with AGC off, per the Caddx spec sheet. As light falls, color goes first, so most night cameras switch to black-and-white. Source: Oscar Liang; Caddx spec sheet.

What does a lux figure actually mean?

Lux measures illuminance, the light falling on a surface. A camera lux figure, properly called minimum illumination, is the least light the camera needs to make a usable image. A lower number means the camera sees in less light. The number means nothing without the test conditions behind it.

How much light is out there. Make: Magazine puts real light levels in context: moonless overcast sky 0.0001 lux, moonless clear sky 0.002, full moon 0.27 to 1.0, civil twilight limit 3.4, full daylight 10,000 to 25,000. A 0.0001 lux camera claims moonless starlight. Source: Make: Magazine.

Why two lux figures cannot be compared directly. Makers measure minimum illumination under different shutter speeds, gain limits, lenses, and definitions of a usable image, so treat a lux figure as a starting point, not a ranking. IRLAB states the rule: a lower published figure indicates a more sensitive camera, provided the figures are quoted under comparable conditions. Source: IRLAB.

Lux vs sensitivity in mV/lux-sec. Some makers state sensitivity in millivolts per lux-second instead of lux: RunCam lists the Phoenix 2 SP V5 at 13,000 mV/lux-sec and the Night Eagle 3 at 11,390 mV/Lux-sec. A sensitivity figure and a lux figure cannot be ranked against each other. Source: post 13426, citing the RunCam manuals via Manuals+.

The only lux figures you can quote. State a lux figure only where the manufacturer published it: the Caddx manual rates the Ratel 2 at 0.0001 lux, and the Foxeer manual rates the Cat 3 at 0.00001 lux. Every other camera here states “not published”.

Camera Sensor Min illumination Source of figure
CADDXFPV Ratel 2 1/1.8-inch starlight 0.0001 lux Caddx manual
Foxeer Cat 3 (reference, not stocked) 1/3-inch CMOS 0.00001 lux Foxeer manual
Foxeer Micro Toothless 3 1/2-inch CMOS starlight Not published Foxeer publishes none
RunCam Phoenix 2 Nite 1/2.8-inch 2MP starlight Not published RunCam publishes none

Starlight or IR: which technology fits your flying?

Starlight amplifies the visible light already there, so it works at dusk, under streetlights, and in moonlight, with no extra hardware. Its limit is total darkness: under a moonless overcast sky with no streetlights, even the best starlight sensor runs out of photons. IR adds light the human eye cannot see, from an illuminator the camera reads. Source: UAVMODEL; Oscar Liang.

IR: bring your own light. An IR illuminator shines near-infrared light, usually at 850nm or 940nm, onto the scene. Oscar Liang built his IR torch from a 48-LED board costing about 8 US dollars, wired to a 3S balance plug and mounted on a GoPro mount. High-power IR units run 5 to 15W and 30 to 60g. Source: Oscar Liang; UAVMODEL.

850nm vs 940nm. An 850nm illuminator emits a faint red glow and cameras see it well; a 940nm illuminator is completely invisible but slightly worse, and it needs a camera with no IR-cut filter. For most pilots 850nm is the practical pick. Source: UAVMODEL.

The IR-cut filter decides everything. A camera can only use IR light if no IR-cut filter sits in the light path. There are four filter designs, and they behave very differently at night.

Filter design How it works Night behavior Example
No IR-cut filter Nothing blocks IR Sees IR light at all times RunCam Phoenix 2 Nite
Removable filter Filter lifts out for night mode Color by day, IR night with filter out CADDXFPV Gazer
Switchable IR-cut (ICR) Filter moves out in the dark Color by day, black-and-white IR night Day/night security-style cameras
Fixed IR-cut filter Filter always in place True color by day, blind to IR at night Most standard day FPV cameras

The Phoenix 2 Nite has no IR-cut filter at all, which is why it is the darkest-flying analog camera in stock. A fixed-filter camera will not see an IR illuminator no matter how bright it is, so check the filter before you buy the light. Source: post 13426; Oscar Liang.

Which lens should a night FPV camera use?

The lens decides how much light reaches the sensor and how much of the scene you see.

Lens choice What it does Night pick
Focal length Sets the field of view; shorter is wider and shows obstacles earlier 2.1mm, 165-degree FOV on the Ratel 2; the Nite is narrower at up to 125 degrees
Aperture (F number) Sets how much light gets in; lower F passes more light F1.0 on the Gazer, widest of any stocked night camera
M12 swap Most micro cameras use M12 threaded lenses, so the lens is replaceable Fit a 2.1mm M12 lens for a wider night view; keep it clean, since a smudged lens scatters streetlight like fog
IR-corrected lens A normal lens focuses visible light and IR at different points, so a day-sharp image goes soft under IR The Cat 3 ships with a large-aperture night-vision lens, per the Foxeer manual

Source: post 13426; Oscar Liang; Make: Magazine; Foxeer Cat 3 manual.

How do you set up a night camera in the OSD?

Most analog night cameras are tuned through an on-screen display menu, reached with the camera joystick or the OSD cable. Change one setting at a time so you know which change fixed the image. Source: UAVMODEL; Oscar Liang; Make: Magazine.

Setting Day value Night value Why it changes
Shutter / exposure Auto, fast Auto, max 1/30s or 1/25s Slower shutter lets in more light
Gain / AGC Low or auto Maximum auto gain Gain brightens the image; the cost is noise
2D noise reduction Off or low Medium to high Cuts grain at the cost of slight softening
3D noise reduction Off On where the camera has it Combines frames to cut noise
WDR On Off or low WDR amplifies noise in dark areas
Day / Night mode Color Auto, or black-and-white Black-and-white drops color noise and improves contrast
White balance Auto Fixed value Auto white balance swings color between lit areas

Step 1: shutter and gain. Set shutter to auto with a maximum exposure of 1/30s or 1/25s. Set the maximum gain as high as the camera allows, often 60dB or more. Accept the grain. Source: UAVMODEL; Oscar Liang.

Step 2: noise reduction. Set 2D noise reduction to medium or high, and 3D noise reduction on. 3D noise reduction combines frames, which cuts noise but creates slight ghosting on fast motion. Source: UAVMODEL; Caddx spec sheet.

Step 3: WDR, white balance, and color. Turn WDR off or low at night: it amplifies noise in dark areas and creates artifacts that look like obstacles. Fix the white balance to one value. Switch Day/Night to auto or straight to black-and-white. Source: UAVMODEL; Oscar Liang.

Step 4: check the power feed. A noisy power feed shows up as rolling lines in the video. Feed the camera from a clean 5V pad or a separate BEC where you can, and keep the camera signal wire away from motor wires and the VTX antenna. Source: post 13426.

What light level are you actually flying in?

Light level Ambient light What works What fails
Dusk 10 to 100 lux Any starlight camera, color mode A small day sensor
Streetlit park 1 to 10 lux Starlight camera, WDR low, B/W optional A day camera with a fixed IR-cut filter
Full moon, clear sky 0.27 to 1.0 lux Starlight camera, high gain, noise reduction on A 0.01 lux day camera
Moonless, clear sky 0.002 lux Starlight at max gain, or IR Any camera that needs 0.01 lux or more
Moonless, overcast 0.0001 lux IR plus a filterless camera Starlight alone, with no ambient light
Total dark, indoors Near zero IR plus a filterless camera Every visible-light camera

Ambient figures from the Make: Magazine lux table. Each step down needs a more sensitive camera or added light. With streetlights, a starlight camera is enough.

How do sensor size, TVL, and latency fit together?

Spec What it means at night What to buy on
Sensor size Bigger gathers more light, so the image holds up longer as light fades 1/2-inch (Toothless 3) or 1/1.8-inch (Ratel 2, Gazer, Moonlight kit); the Nite is 1/2.8-inch but has no IR-cut filter
TVL Analog horizontal resolution; matters least at night 1200TVL on most stocked analog night cameras, 1500TVL on the Nite and Gazer
Latency Analog runs about 20 to 26 ms and degrades gracefully; digital is sharper but a weak signal freezes or breaks up Fly analog for the live feed, record digital for the footage

Source: post 13426; Oscar Liang; IRLAB.

What mistakes ruin a night camera image?

  • Buying on the lux figure alone. Check the sensor size and the test conditions too.
  • Fitting a day camera and hoping the settings save it. No OSD setting adds photons the sensor never collected.
  • Leaving the IR-cut filter in place and buying an IR light. A fixed-filter camera cannot see IR light.
  • Mounting the IR panel next to the lens. IR light in the lens creates glare. Mount the panel on top of the quad, away from the lens. Source: Oscar Liang.
  • Leaving WDR on at night. WDR amplifies noise and creates artifacts that look like obstacles.
  • Flying a new spot, or flying fast, at night. Recon in daylight first, then slow down and add 50 percent extra clearance to every gap. Source: UAVMODEL.
  • Skipping the strobe and the buzzer. The strobe keeps the quad legal and visible; a self-powered buzzer finds it in the dark.

How do you fix a night image that is dark, noisy, or washed out?

Most night image problems are settings or power, not a bad camera.

The image is dark even at dusk. Check that Day/Night is set to Auto and not locked to Day. If the camera has an IR-cut filter, the filter is blocking the light you need in near darkness. Check the shutter maximum: if it is capped at 1/120s, raise it to 1/30s.

The image is noisy and grainy. Turn 2D noise reduction to medium or high, and 3D noise reduction on where the camera has it. Switch to black-and-white mode, which drops the color noise.

The image is washed out around lights. Set WDR off or low at night. Angle the camera down so streetlights sit at the top of the frame. Check for a light shining into the lens, including your own strobe or IR panel mounted too close.

The video has rolling lines or interference. The camera power feed is noisy. Move the camera power to a filtered 5V pad or a separate BEC, and keep the camera signal wire away from motor wires and the VTX antenna.

The camera switches between color and black-and-white on its own. Day/Night set to Auto can hunt when the threshold sits in the middle of your light level. Lock it to black-and-white for the flight. Source: Oscar Liang.

Which night camera should you buy for your flying?

Buy for the light level you fly in. The full per-use picks are in the companion buying guide, How to Choose an FPV Camera for Night and Low-Light Flying.

Dusk and streetlit flying, one camera for everything. Buy the CADDXFPV Ratel 2 (ID 20161) at $68.99 sale, $82.99 regular: the only manufacturer-published 0.0001 lux rating in stock, a 1/1.8-inch starlight sensor, and a 165-degree view from the 2.1mm lens. If the budget is tight, buy the Caddx Ratel 2 V2 (ID 13206) at $44.99 instead: same sensor, resolution, lens, and voltage range. Note: the two listings are the same camera model; keeping both is Alex’s call.

After dark, or flying with IR. Buy the RunCam Phoenix 2 Nite (ID 20157) at $104.99 sale, $126.99 regular. No IR-cut filter, 1500TVL, and automatic color to black-and-white switching. It is the darkest-flying analog camera in stock.

Dusk freestyle where sensor size matters most. Buy the Foxeer Micro Toothless 3 (ID 20159) at $89.99 sale, $108.99 regular. Its 1/2-inch CMOS sensor is the largest sensor on any stocked analog camera here. Foxeer publishes no lux figure for it.

Reference only, not stocked. The Foxeer Cat 3 (0.00001 lux per the Foxeer manual) is not stocked at QRC.

Parts used in this guide

Prices and stock were verified live on qualityrcparts.com on 2026-11-21. All four items below are in stock and purchasable.

Shipped fast and securely from our secure facility in Queensbury, NY. QRC ships within the USA only.

Related guides

FAQ

What is a starlight FPV camera? A starlight FPV camera uses a large, sensitive CMOS sensor built to make a flyable image in very low light. “Starlight” is a marketing term, not a standard, so judge it by sensor size and manufacturer-published sensitivity. Source: UAVMODEL; Oscar Liang.

What lux rating do I need for night FPV flying? For dusk and streetlit flying, a camera rated at 0.0001 lux, like the Ratel 2 per the Caddx manual, holds a flyable image. For moonless dark with no streetlights, no lux rating is enough on its own: you need an IR illuminator plus a camera with no IR-cut filter. Source: Caddx manual.

Can I compare two cameras by their lux figures? Only if the figures were measured the same way, and they rarely are. Use the lux figure as a starting point, then check sensor size and filter type. Source: IRLAB.

What is the difference between starlight and IR night vision? Starlight amplifies the visible light already in the scene and needs some ambient light. IR adds near-infrared light from an illuminator, which an IR-sensitive camera reads and the human eye cannot see. Source: Oscar Liang; UAVMODEL.

Should I use 850nm or 940nm IR light for FPV? Use 850nm for most flying: cameras see it well. 940nm is completely invisible with no red glow, but performance is slightly worse, and it needs a camera with no IR-cut filter. Source: UAVMODEL.

What OSD settings should I change for night flying? Set the shutter to auto with a maximum of 1/30s, raise the gain limit to maximum, turn 2D and 3D noise reduction on, turn WDR off or low, fix the white balance, and switch to black-and-white mode. Source: UAVMODEL; Oscar Liang.

Sources

Last updated: 2026-11-21