The type of motor driver you need is decided by the motor, not by the microcontroller: a brushed DC motor needs an H-bridge, a stepper motor needs a chopper driver, a brushless motor needs a three-phase ESC, and a hobby servo needs no driver board at all. Pick the type first, then pick the chip.
What is a motor driver?
A motor driver is the circuit between a low-power control signal and a motor that needs real power. An Arduino pin can supply only about 20 to 40 mA, while even a small TT gear motor draws 150 to 250 mA running and close to 1 A stalled. Connect a motor straight to a pin and the pin burns out. A motor driver keeps the high motor current off the board. Source: QRC post 16272.
Every driver type does the same three jobs in a different way: it switches power to the motor windings, controls speed or position, and protects the board and the motor from spikes. The differences come from what the motor needs switched: a brushed DC motor needs its two wires flipped in polarity, a stepper motor needs its two coils energized in sequence with the current capped, and a brushless motor needs three phases energized in a rotating sequence timed to the rotor. Those three switching jobs are three different driver types, and they are not interchangeable.
What are the types of motor drivers?
Six types cover nearly every Arduino and hobby build.
| Driver type | Motor it runs | Control signal | Best for |
|---|---|---|---|
| Brushed DC H-bridge | Brushed DC motor | PWM plus direction pins | Robot wheels, gear motors, winches, pumps |
| Stepper chopper | Bipolar stepper motor | STEP and DIR pulses | 3D printers, CNC axes, camera sliders |
| BLDC driver / ESC | Brushless DC motor | PWM, PPM, or DShot throttle | Drones, RC cars, fans, gimbals |
| Servo control | Hobby RC servo | Position PWM signal | Robot arms, steering, control surfaces |
| Single-direction switch | Any one-way DC load | One logic pin | Fans, one-way pumps, solenoids |
| Smart driver | DC, stepper, or BLDC | SPI, I2C, UART, or STEP/DIR | Builds that need stall detection or telemetry |
Sources: Number Analytics, ElecBlog, ThinkRobotics, Schneider Electric.
How does a brushed DC H-bridge driver work?
A brushed DC motor spins when voltage is applied across its two wires and reverses when the polarity flips. An H-bridge is four switches in the shape of the letter H, with the motor as the crossbar: one diagonal pair drives current one way, the other pair the other way. Source: ThinkRobotics motor driver basics; ElecBlog motor driver selection guide.
Two switch technologies do this job. Bipolar H-bridges, such as the L298N, use bipolar transistors: the ST L298 datasheet DS0218 Rev 5 lists a total saturation drop of 1.8 V to 3.2 V at 1 A, so on a 7.4 V battery the motor sees about 4.2 V to 5.6 V. MOSFET H-bridges, such as the TB6612FNG and DRV8833, use MOSFETs: the Toshiba TB6612FNG datasheet lists about 0.5 ohm total on-resistance, so at 1 A it drops about 0.5 V, and the TI DRV8833 datasheet SLVSAR1E Rev E lists about 0.36 ohm, so at 1 A it drops about 0.36 V. A MOSFET driver delivers nearly the full battery voltage to the motor. Source: QRC post 23379; ST L298, Toshiba TB6612FNG, and TI DRV8833 datasheets.
Never turn on both switches on the same side at once: that shorts the supply to ground, a fault called shoot-through, and it destroys the switches. An H-bridge also decides how the motor stops: shorting the terminals brakes the motor fast, and letting them float lets it coast. Source: ElecBlog motor driver selection guide; TrueGeometry motor driver circuits guide; QRC post 16272.
How does a stepper chopper driver work?
A stepper motor moves in fixed angles as its coils are energized in sequence. A stepper driver takes two signals, STEP and DIR, and handles the coil sequencing itself. Source: ElecBlog motor driver selection guide; QRC post 16272.
What makes a stepper driver a different TYPE is current chopping. A stepper coil is a low-resistance winding that would draw far more current than it is rated for at the supply voltage. The driver measures the coil current and switches off the instant it reaches the rated limit, then switches back on, thousands of times per second. That holds the coil at its rated current while the supply runs much higher than the motor rated voltage, so a low-voltage NEMA 17 runs safely from 12 V or 24 V. A DC H-bridge has no current limit, so the supply voltage must stay near the motor rating. Source: QRC post 16272; ElecBlog motor driver selection guide.
Microstepping. A chopper driver can split each full step into smaller steps. The A4988 runs full step to 1/16 step, the DRV8825 runs full step to 1/32 step, and the TMC2209 runs to 1/256 interpolated steps. Microstepping makes motion smoother and quieter, but it does not add holding torque. The A4988 listing states up to 1.2 A continuous per phase, and the DRV8825 listing states 1.5 A per coil, with the chip maximum at 2.5 A per coil with heatsinking at 24 V and 25 C. Set the current limit with the onboard trim potentiometer before connecting the motor. Source: QRC product listings 17896 and 23573; QRC post 16272.
How does a BLDC driver work?
A brushless DC motor has no brushes and no mechanical commutator. The magnets sit on the rotor and the windings sit on the stator, so the driver must commutate electronically, switching current between the three phases in a rotating sequence timed to the rotor position. The power stage is a three-phase inverter: three half-bridges, six switches in total. No H-bridge board in this guide can run a brushless motor: if your motor has three wires and no brushes, shop for an ESC, not a driver module. Source: ElecBlog motor driver selection guide; MIKROE motor control basics guide; QRC post 16272.
Six-step vs field-oriented control. The basic method is six-step, also called trapezoidal drive: two phases conduct at a time and the third floats, which works but produces torque ripple. The advanced method is field-oriented control (FOC), which controls torque and flux separately for smooth torque, high efficiency, and full torque at zero speed. FOC needs position feedback and clean phase-current sensing. For a hobby drone or RC car, six-step is the normal choice; for a gimbal, FOC is worth it. Source: MIKROE motor control basics guide; Wevolver motor controller guide.
Sensored vs sensorless. The driver must know where the rotor is to time the phase switching. Sensored drivers read Hall-effect sensors and start reliably at low speed. Sensorless drivers read back-EMF from the unpowered phase, which works once the motor is spinning but is unreliable at a standstill, so a sensorless ESC that stutters on startup is usually losing the rotor. Source: ElecBlog motor driver selection guide; Daily Slate ESC and driver basics.
When to use a BLDC driver. Use one for drones, RC vehicles, fans, and gimbals. Do not use one for a brushed motor or a stepper. Source: ElecBlog motor driver selection guide; Schneider Electric motor driver guide.
What about servos and single-direction loads?
Servo control is not a driver board. A hobby RC servo has its own driver, gears, and feedback built into the case. The Arduino sends it a position signal and the servo moves to that angle and holds it. What a servo needs is its own power: feed it from a separate 5 to 6 V supply, join the grounds, and send only the signal wire to the Arduino. Powering even one servo from the Arduino 5 V pin can brown the board out when the servo moves under load. Source: QRC post 16272; ThinkRobotics motor driver basics.
Single-direction switches. Some loads never reverse: a one-way pump, a fan, a solenoid. Those need no H-bridge at all. A single logic-level MOSFET and a flyback diode do the job: the MOSFET switches the load on and off, PWM sets the speed, and the diode gives the inductive kick a safe path when the switch turns off. Source: TrueGeometry motor driver circuits guide; QRC post 16272.
Integrated vs discrete vs smart drivers
Driver types also split by how the power stage is built: integrated driver ICs hold the MOSFETs, the gate drivers, and the protection (thermal shutdown, overcurrent trips, undervoltage lockout) in one chip. The L298N, TB6612FNG, DRV8833, A4988, and DRV8825 are all integrated drivers. Discrete drivers use separate MOSFETs, gate driver ICs, diodes, and current-sense resistors on your own board. They scale to high-power systems an integrated chip cannot reach, such as the 43 A peak BTS7960 class, but you design the gate timing and protection yourself. Smart drivers add a microcontroller interface and on-chip sensors: SPI, I2C, UART, or STEP/DIR control, plus stall detection and telemetry. The TMC2209 is the example in the QRC store: StallGuard4 stall detection, CoolStep current reduction, and UART configuration. The Trinamic TMC2209 datasheet Rev 1.05 lists 2 A RMS and 2.8 A peak per coil. Source: ElecBlog motor driver selection guide; PCBSync motor controller PCB design guide; QRC post 16272; Trinamic TMC2209 datasheet Rev 1.05.
The TMC2208 current rating is not stated on the QRC listing, and no datasheet figure is quoted for it here: check the Trinamic datasheet for the exact part before buying.
How do the types compare?
| H-bridge (brushed DC) | Stepper chopper | BLDC / ESC | Servo control | |
|---|---|---|---|---|
| Position control | No, speed only | Yes, open loop step count | No, speed only unless sensored FOC | Yes, closed loop angle |
| Holds position at rest | No | Yes, holding torque | No | Yes |
| Reverses | Yes | Yes, DIR pin | Yes, reverse commutation | Yes, angle command |
| Efficiency | MOSFET high, bipolar low | Low, wastes power holding | High, 85 to 95 percent | High for the load |
| Control signal | PWM plus direction | STEP plus DIR | Throttle PWM, PPM, or DShot | Position PWM |
| Example chips | L298N, TB6612FNG, DRV8833 | A4988, DRV8825, TMC2209 | BLHeli_S, BLHeli_32 ESCs | None, built into the servo |
Which type should I use?
Answer these five questions in order.
- What motor is it? Brushed DC with two wires means H-bridge. Stepper with four or five wires means chopper or ULN2003. Brushless with three wires means BLDC driver or ESC. Hobby servo means no driver board.
- Must it hold a position? Yes means stepper chopper or servo: a DC driver cannot hold position, and neither can a BLDC driver without sensored FOC and position feedback.
- Must it reverse? Yes means H-bridge, chopper, or a reversing BLDC driver.
- What is the stall current? Size the driver from the motor stall current, not the running current: continuous current must be at least 1.5 times the motor continuous running current, and peak current must cover the stall current (post 16272). With no datasheet, measure the coil resistance and use I = V / R.
- What is the supply voltage? The driver must cover the full supply range, including a LiPo at full charge: a 3-cell LiPo peaks at 12.6 V, above the DRV8833 10.8 V ceiling, and a 4-cell LiPo at full charge exceeds the TB6612FNG 13.5 V ceiling. Check the ceiling before you buy.
Quick picks by project. Robot car wheels: H-bridge (TB6612FNG battery builds, L298N above 13.5 V). 3D printer or CNC axis: stepper chopper (A4988, DRV8825, TMC2209). Drone or RC car: BLDC ESC (post 21990). Robot arm joint: servo or stepper chopper (post 21979). One-way fan or pump: single MOSFET switch. Big motor above 2 A stall: BTS7960-class H-bridge.
What are the common mistakes?
- Buying a driver for the board instead of the motor. The Arduino does not decide the driver type: an L298N cannot run a brushless motor and an A4988 cannot run a DC motor.
- Using an H-bridge as a stepper driver. A dual H-bridge can energize a bipolar stepper, but it cannot limit current, so it is a poor stepper driver in practice. Source: QRC post 16272.
- Expecting a DC driver to hold position. An H-bridge has no position feedback and no holding torque: a build that must hold still needs a stepper or a servo.
- Sizing by running current instead of stall current. A TT motor that draws 0.25 A while rolling can draw over 1 A stalled against a wall. A driver sized for running current overheats the first time a wheel blocks. Source: QRC post 23379.
- Ignoring the voltage ceiling. A 3-cell LiPo at full charge is 12.6 V, above the DRV8833 ceiling of 10.8 V, and a 4-cell LiPo at full charge is above the TB6612FNG ceiling of 13.5 V. Both look like a dead driver, and both are a wrong type choice.
How do I fix a motor driver problem?
The motor does not move at all. Check the type first: is this driver made for this motor? Then check the common ground and the enable pin: STBY HIGH on the TB6612FNG, EN tied LOW and SLP HIGH on the A4988. A board that does nothing is usually an enable pin.
The motor is slow and weak. On a bipolar H-bridge such as the L298N, the driver drops 1.8 V to 3.2 V at 1 A, and that loss becomes heat. Raise the supply by about 2 V above the motor rating, or switch to a MOSFET driver such as the TB6612FNG. On a stepper, the current limit is set too low: check VREF. Source: QRC posts 16272 and 23379.
The driver overheats and shuts down. The motor stall current exceeds the driver limit, or the headline current is being treated as continuous. Plan for roughly half the headline number for sustained running, add a heatsink and airflow, and do not force the motor against a stall.
The stepper vibrates but does not turn. Coil pairs are mismatched, or VREF is too low. Find the coil pairs with a multimeter, then check the current limit. A stepper that loses steps mid-move is usually accelerating too fast, or hitting mid-band resonance at 2 to 4 revolutions per second: slow the ramp or switch to a TMC2209. Source: QRC post 16272.
Parts used in this guide
Prices and stock were verified live on qualityrcparts.com on 2026-11-21. All four items below are in stock and purchasable, each an example of one driver type in this guide, not a per-chip recommendation: post 16272 and post 23379 cover chip picks in depth.
- HiLetgo L298N Motor Driver Board, Dual H-Bridge DC and Stepper Motor Controller for Arduino (ID 19615) – $6.99 sale, $8.99 regular. Bipolar H-bridge type. 5 to 35 V DC, up to 2 A per channel.
- TB6612FNG Dual DC/Stepper Motor Driver Module, 3-Pack (ID 18849) – $13.99 sale, $17.99 regular. MOSFET H-bridge type. 2 DC motors at 1.2 A continuous per channel, 4.5 to 13.5 V per the Toshiba datasheet.
- A4988 Stepper Motor Driver Module with Heat Sink, Single (ID 17896) – $6.99. Stepper chopper type. Step and direction interface, full step to 1/16 microstepping, up to 35 V, up to 1.2 A continuous per phase.
- DRV8825 Stepper Motor Driver Module with Heatsink, Single (ID 23573) – $6.99. Stepper chopper type. StepStick format, full step to 1/32 microstepping, rated 1.5 A per coil, chip maximum 2.5 A per coil.
Shipped fast and securely from our secure facility in Queensbury, NY. QRC ships within the USA only.
Related guides
- How to Choose the Right Motor Drivers for Arduino Use
- L298N vs TB6612 vs DRV8833: Which Motor Driver for Your Robot
- How Stepper Motors Work: Steps, Coils, and Microstepping
- Stepper DC Driver Choice: ULN2003, L298N, A4988, and More
- Servo vs Stepper for a Small Robot Arm
- ESC Current Rating, Motor KV, and Battery Match for FPV
FAQ
What is a motor driver? A motor driver is an electronic circuit between a microcontroller and a motor: it takes a low-power control signal and switches the larger motor current from a separate supply, controlling speed, direction, or position. Source: Number Analytics motor drivers in robotics FAQ.
What are the different types of motor drivers? The main types are brushed DC H-bridge drivers, stepper chopper drivers, BLDC drivers and ESCs, servo control, single-direction switches, and smart drivers.
Can I run a motor without a motor driver? Technically yes, with switches or relays, but it is inefficient and unsafe: without a driver you cannot regulate speed or direction precisely, and you risk damaging both the motor and the control unit. Source: Schneider Electric motor driver FAQ.
Can I use a motor driver with any type of motor? No. Motor drivers are designed for specific motor types: H-bridge for brushed DC, chopper for stepper, three-phase ESC for brushless. Source: Number Analytics motor drivers in robotics FAQ.
What is the difference between a motor driver and an ESC? An ESC is a BLDC driver packaged for radio control: it takes a throttle signal and handles three-phase electronic commutation. A motor driver module is the same power stage sold for microcontroller builds. Source: Daily Slate ESC and driver basics.
Why does my L298N get so hot? Because the L298N uses bipolar transistors, about 2 V to 3 V is lost across it while current flows, and that loss turns into heat: at 1 A the driver produces about 2 W of heat. Keep the current low or switch to a MOSFET driver. Source: QRC post 16272; ST L298 datasheet.
Sources
- Quality RC Parts, How to Choose the Right Motor Drivers for Arduino Use: https://qualityrcparts.com/best-motor-drivers-for-arduino-usa/
- Quality RC Parts, L298N vs TB6612 vs DRV8833: Which Motor Driver for Your Robot: https://qualityrcparts.com/l298n-vs-tb6612-vs-drv8833/
- Quality RC Parts, How Stepper Motors Work: Steps, Coils, and Microstepping: https://qualityrcparts.com/how-stepper-motors-work/
- Quality RC Parts, Stepper DC Driver Choice: ULN2003, L298N, A4988, and More: https://qualityrcparts.com/stepper-dc-driver-choice-uln2003-l298n-a4988/
- Quality RC Parts, L298N Robot Car: Wire and Drive Two DC Motors: https://qualityrcparts.com/l298n-robot-car-motor-control/
- Quality RC Parts, Servo vs Stepper for a Small Robot Arm: https://qualityrcparts.com/servo-vs-stepper-small-robot-arm/
- Quality RC Parts, ESC Current Rating, Motor KV, and Battery Match for FPV: https://qualityrcparts.com/esc-current-rating-motor-kv-battery-match-fpv/
- Quality RC Parts, DM542 and DM860H Driver Sizing: https://qualityrcparts.com/dm542-dm860h-driver-sizing/
- Quality RC Parts store listings, checked live 2026-11-21 (IDs 19615, 18849, 17896, 23573)
- ST L298 Dual Full-Bridge Driver datasheet, DS0218 Rev 5, October 2023 (via QRC post 23379)
- Toshiba TB6612FNG datasheet, 2014-10-01 edition (via QRC post 23379)
- Texas Instruments DRV8833 Dual H-Bridge Motor Driver datasheet, SLVSAR1E Rev E, July 2015 (via QRC post 23379)
- Trinamic TMC2209 datasheet Rev 1.05 (via QRC post 16272)
- Number Analytics, Motor Drivers in Robotics: https://www.numberanalytics.com/blog/ultimate-guide-motor-drivers-robotics
- Number Analytics, Motor Drives in Mechatronics: A Comprehensive Guide: https://www.numberanalytics.com/blog/ultimate-guide-to-motor-drives-in-mechatronics
- AI Future School, Motor driver functions and types in electronics: https://www.ai-futureschool.com/en/electronics/understanding-motor-drivers-for-electronics.php
- Schneider Electric, Motor Driver: Types, Working and Applications: https://eshop.se.com/in/blog/post/motor-driver-guide.html
- ElecBlog, Motor Drivers: Selection, Wiring, and Troubleshooting for Robust Motion Control: https://elecblog.com/motor-drivers-selection-wiring-and-troubleshooting-for-robust-motion-control/
- ThinkRobotics, What is a Motor Driver? Understanding the Basics and Applications: https://thinkrobotics.com/blogs/learn/what-is-a-motor-driver-understanding-the-basics-and-applications
- TrueGeometry, Motor Driver Circuits: https://blog.truegeometry.com/api/exploreHTML/2d10dcc13630641a84f831662225eb17.exploreHTML
- MIKROE, Motor Control Basics: The Embedded Engineer’s Complete Guide: https://www.mikroe.com/blog/motor-control-basics
- PCBSync, Motor Controller PCB Design: BLDC, Stepper and VFD: https://pcbsync.com/motorcontroller-pcb-design/
- Wevolver, Motor Controller: Types, Design Considerations, Control Strategies, and Selection for Engineers: https://www.wevolver.com/article/motor-controller-types-design-considerations-control-strategies-and-selection-for-engineers
- Daily Slate, Choosing the Right Motor Controller: ESC and Driver Basics: https://www.dailyslate.site/choosing-the-right-motor-controller-esc-and-driver-basics
Last updated: 2026-11-21
