LiPo Storage Voltage Guide: 1S to 6S Tables

Store a LiPo battery at about 3.8V per cell: about 7.6V for a 2S pack, 11.4V for a 3S pack, 15.2V for a 4S pack, and 22.8V for a 6S pack. Use your charger storage mode to get there, check each cell first, and re-check stored packs every two to four weeks. Never store a pack full at 4.20V per cell for weeks, and never store one flat near 3.0V per cell. The 3.8V figure is the commonly cited figure, not a manufacturer spec.

What is LiPo storage voltage?

Storage voltage is the per-cell voltage a LiPo pack rests at between uses. For a standard LiPo pack the commonly cited target is about 3.8V per cell, with published guides giving a 3.80 to 3.85V range. It sits in the middle: full is 4.20V per cell, the floor is about 3.0V per cell.

A pack left fully charged rests at maximum voltage, where the side reactions inside the cell run fastest: capacity fades, internal resistance climbs, and gas builds up, which is the puffing pilots recognise. Heat makes all of it worse. A pack left empty fails the other way: resting voltage drifts slowly downward until the damage is structural and irreversible, and charging a deeply over-discharged cell is a safety problem, not a recovery project. Storage voltage avoids both at once.

About 3.8V per cell is a commonly cited figure, not a manufacturer spec, and no official datasheet was found for the packs QRC stocks. Sources disagree slightly on the band: SwellRC gives 3.80 to 3.85V per cell, HobbyKing gives 3.7 to 3.85V, and Gens Ace gives a wider 3.6 to 3.9V, reported in the Medium storage guide. This draft uses 3.80 to 3.85V as the target band and treats 3.7 to 3.85V as acceptable, where the sources overlap.

Storage voltage is a per-cell number, not a pack total. A 4S pack at storage reads about 15.2V total, but the four individual cell readings are the real record, because cells drift apart as packs age. Judge a pack by its worst cell, not its total.

What voltage do you store each pack at?

Multiply the per-cell figure by the number of cells. A pack is on target when every cell reads inside the 3.80 to 3.85V band.

Pack Full (4.20V per cell) Storage low (3.80V per cell) Storage high (3.85V per cell) Nominal (3.70V per cell) Minimum (about 3.0V per cell)
1S 4.20V 3.80V 3.85V 3.70V About 3.0V
2S 8.40V 7.60V 7.70V 7.40V About 6.0V
3S 12.60V 11.40V 11.55V 11.10V About 9.0V
4S 16.80V 15.20V 15.40V 14.80V About 12.0V
5S 21.00V 19.00V 19.25V 18.50V About 15.0V
6S 25.20V 22.80V 23.10V 22.20V About 18.0V

A 3S pack is on target when every cell reads between 11.40V and 11.55V total. Do not aim for the nominal voltage: 3.70V per cell is the average label figure, not a storage target. Never charge a standard LiPo cell past 4.20V, and never run a cell below about 3.0V at rest: cells run that low are damaged, and many chargers will refuse them.

What does a voltage reading mean?

Read each cell on the checker, find the band, and act on the lowest cell, not the average.

Per-cell reading What it means What to do
Above 4.20V Overcharged Do not charge it or fly it. Retire the pack.
4.20V Full Fine if you fly within a day or two. Storage-charge it down if the pack will sit longer.
3.86V to 4.19V Above the storage band Storage-charge it down before the pack sits for more than a few days.
3.80V to 3.85V On target for storage Put it away. Re-check every two to four weeks.
3.70V to 3.79V Below target, inside the wider range Fine for a short rest. Top it back to target for a long rest.
3.60V to 3.69V Low for storage Bring it back to storage voltage soon. Watch the low cell.
Below 3.60V Too low to leave sitting Bring it back promptly. Never store below 3.6V per cell.
About 3.0V or below Damaged, likely unrecoverable Do not force it on NiMH mode. Retire the pack.
0.00V on one cell Dead cell The pack is done. Retire it and dispose of it following local rules.

The bands follow the cited ranges, not a maker spec: 3.80 to 3.85V from SwellRC, 3.7 to 3.85V from HobbyKing, 3.6 to 3.9V from Gens Ace as reported in the Medium storage guide, and the 3.6V floor from Hanery. Your pack maker guidance wins when it gives its own number.

After a storage cycle the cells should read close together; a cell clearly apart from its siblings is a flag. At full charge, every cell should read 4.20V, or within about 0.03V of it.

How do you check a pack before storage?

Check the pack cell by cell, every time, before it goes on the shelf.

  1. Let the pack cool. Wait until the pack is at room temperature. Never charge a hot pack, and never charge a frozen or very cold pack.
  2. Inspect the pack. Do not storage-charge a swollen, hot, leaking, punctured, or crushed pack.
  3. Plug the balance lead into the checker. The CellMeter8 LiPo Battery Checker (ID 3485) reads up to 8 cells through the balance lead, and the 3-in-1 Battery Voltage Checker Balancer and Discharger (ID 12052) shows cell voltages on its LCD display. Plug it in fully and wait for the reading to settle.
  4. Read every cell, not the total. The lowest cell decides what happens next, using the reading bands table above.
  5. Unplug the pack from the model first. A switched-off model is not a disconnected model. Unplug the main lead after every session, so nothing can drain the pack while it sits.

A multimeter on the main lead is a weaker check: it reads the pack total only, so it cannot see a single low cell hiding inside a healthy-looking total. The Jönköping chapter uses a multimeter on the XT60 contacts to read a 3S pack total, between about 11.1V at storage and 12.6V full. For storage, use a checker that reads each cell.

How do you storage-charge a pack on a balance charger?

Storage mode works in both directions: it charges a flown pack up, and it discharges a full pack down. Run it after every session for packs you will not use within a day or two. The steps below use the B6 80W Mini LiPo Balance Charger and Discharger with Power Supply (ID 18960), whose listing states a storage charge function, 1 to 6 cells, and LiPo, Li-ion, and LiFe support.

  1. Let the pack cool, inspect it, and put it in the safe bag. Never storage-charge a swollen, hot, or damaged pack. Set the Zeee Small LiPo Safe Bag (ID 20106) on a non-flammable surface, pack inside, leads out where you can reach them.
  2. Connect the main lead, then the balance lead. Without it the charger steers by the pack total, and one high cell can finish above the target.
  3. Select LiPo storage mode. Not balance charge, not fast charge, not plain charge.
  4. Confirm the cell count on the display. It should match the label. If it shows fewer cells, or a cell reads 0.00V, stop.
  5. Start the cycle and stay in the room. A storage discharge takes longer than a storage charge, because most hobby chargers can only shed a small amount of power as heat when discharging. Start storage work when flying ends.
  6. Verify with the checker when the charger reports done. Every cell should read 3.80 to 3.85V. Flag a cell that sits clearly apart.
  7. Unplug the balance lead first, then the main lead. Label the pack with the date and the word storage.

How do you storage-charge with the stocked checker and discharger?

3-in-1 Battery Voltage Checker Balancer and Discharger (ID 12052), $12.49. The listing states it checks pack voltage, balances cells, and discharges packs for storage, with cell voltages on its LCD display. Use it to bring a full pack down to storage voltage: plug in the balance lead, read each cell, select the discharge mode, and verify that every cell lands in the 3.80 to 3.85V band. It discharges; it does not charge a flown pack up. Run it on a non-flammable surface with its airflow unobstructed, attended, because it gets hot doing its job.

CellMeter8 LiPo Battery Checker (ID 3485), $19.99. A checker and balancer for up to 8 cells. It reads each cell through the balance lead, which is the check this whole guide depends on. It does not charge or discharge, so pair it with the B6 80W Mini for the storage cycle.

ImaxRC B3 Pro Balance Charger (2S/3S) (ID 16863), $15.99. A compact balance charger for 2S and 3S LiPo packs only, per its listing, which states no storage program: check the manual before you count on one.

No storage mode on your charger? Charge the pack and stop when the per-cell reading reaches about 3.8V, watching the checker as it climbs. That tip follows the Medium storage guide: after a normal run a pack is usually below storage voltage. If the pack is full instead, run the charger discharge function, or use the 3-in-1 discharger above.

How long can a pack sit at each voltage?

How long a pack can sit depends on where it starts.

Starting voltage How long it can sit What to do
Full, 4.20V per cell A day or two Normal between sessions. Past that, storage-charge it down.
Storage, 3.80 to 3.85V per cell Weeks to months, with checks The resting state. Re-check every two to four weeks.
Nominal, 3.70V per cell Weeks, with checks Below the target band, so it has less margin. Top it back to the storage band before a long rest.
Flat, below 3.60V per cell Do not leave it sitting Bring it back promptly. A flat pack left over 7 days can over-discharge, per Traxxas guidance.
Below about 3.0V per cell Already damaged Do not store or force-charge it. Retire the pack.

The sources split on check cadence: the QRC storage guide says every two to four weeks, Gens Ace suggests every few months. This draft recommends the two to four week check. Label every pack with its storage date and a rough cycle count.

For a winter or off-season rest, put every pack at storage voltage before the break, keep them in a cool, dry, stable indoor spot, and keep the two to four week check going. Before the first use after a long rest, balance-charge the pack and check that all cell voltages ended close together.

What about LiHV and LiFe packs?

LiHV and LiFe packs are not standard LiPo packs. Check the label: the chemistry is printed on the pack, and the setting must match it.

LiHV packs charge to 4.35V per cell instead of 4.20V and need the LiHV setting; charging a normal LiPo on it overcharges it. Use the storage mode your charger specifies for LiHV packs where it offers one. Where it does not, rest LiHV packs at the same about 3.8V per cell region as standard LiPos, per the DroneCamps storage guide; the RobotCombatWiki safety page gives about 3.8 to 3.85V per cell. A LiHV pack left at its full 4.35V rests harder than a standard pack left at 4.20V, so bring LiHV packs down promptly.

LiFe packs use their own setting with a full voltage of about 3.6V per cell, per SwellRC. The RobotCombatWiki safety page gives about 3.3V per cell as the LiFe storage figure. Treat that figure as less settled: it comes from one safety page. Follow the LiFe pack maker docs first.

Never charge a standard LiPo on the LiHV setting, and never charge a LiHV pack on a setting you have not confirmed matches its label.

Which storage setup fits your fleet?

Situation Voltage action Gear
Flying in a few days to a week Storage-charge now, so a cancelled session never strands a full pack B6 80W Mini charger (ID 18960)
Not flying for weeks or months Storage voltage, safe bag, checks every two to four weeks B6 80W Mini charger (ID 18960), Zeee safe bag (ID 20106)
Winter or off-season rest Storage voltage before the break, cool dry spot B6 80W Mini charger (ID 18960), Zeee safe bag (ID 20106)
Pack came home full and unflown Discharge it down to storage, do not leave it full 3-in-1 discharger (ID 12052) or B6 80W Mini (ID 18960)

What mistakes ruin packs in storage?

Most stored packs are not ruined by one dramatic mistake. Smaller habits repeat over time.

Mistake What happens Fix
Storing packs full for weeks Cells age fastest at full voltage, gas builds, packs puff Storage-charge to about 3.8V per cell when the pack sits
Storing packs flat Resting voltage drifts down until a cell is damaged for good Never store a pack flat
Storage-charging without the balance lead Charger steers by the pack total, one cell can finish above target Connect the balance lead every cycle
Reading the pack total only A low cell hides inside a healthy-looking total Read each cell; judge by the worst cell
Leaving the pack plugged into the model A switched-off model can still drain the pack while it sits Unplug the main lead after every session
Storing in a hot car or in the sun Heat multiplies every ageing reaction Cool, dry, stable indoor spot, out of direct sun
Packing packs loose together or sealed airtight Loose packs can short terminal to terminal; a failing cell vents gas a sealed box cannot release Keep plugs capped or packs separated, use a vented container or a LiPo safe bag
Forgetting stored packs for months Drift goes unnoticed until a cell is too low to save Check every two to four weeks, label each pack

Why is my pack off storage voltage?

The storage discharge on the charger takes hours. Normal: charger discharge power is small by design. Start storage work when flying ends, or use a dedicated discharger set to the storage endpoint, such as the 3-in-1 checker and discharger (ID 12052).

One cell always finishes below the others. That cell is ageing faster than its siblings. Flag the pack and retire it when the spread keeps growing.

A pack was found resting near empty after a long break. Self-discharge plus time; it was likely stored low or left connected to a load. If any cell is deeply over-discharged, treat it as end of life and dispose of it safely rather than charging it.

The charger reports a low-voltage error and will not start a storage cycle. One or more cells dropped below the safe level, typically about 3.0V per cell. The pack was run too flat, left plugged in, or stored flat. Do not force it by charging on NiMH mode: that bypasses the safety cutoff that refused the pack. If a cell reads 0.00V, the pack is done.

Parts used in this guide

Prices and stock verified live 2026-11-21; all four are in stock and purchasable.

Also named in the body text, verified live in stock and purchasable on 2026-11-21: ImaxRC B3 Pro Balance Charger (2S/3S) (ID 16863) – $15.99. 2S and 3S LiPo only. No storage program is stated in its listing.

Shipped fast and securely from our secure facility in Queensbury, NY, providing fast, high quality USA shipping. QRC ships within the USA only.

Related guides

FAQ

What is the storage voltage for a LiPo battery? About 3.8V per cell, with published guides giving a 3.80 to 3.85V range. A 3S pack stores at about 11.4V and a 6S pack at about 22.8V. Source: SwellRC, Jönköping University, and DroneCamps guides.

What voltage should a 2S or 3S LiPo be stored at? About 7.6V for a 2S pack and 11.4V for a 3S pack, roughly 3.8V per cell. Source: Medium storage guide.

How long can a LiPo stay fully charged? A day or two is normal between sessions. Smart packs start discharging to storage after 72 hours by default. Past that, storage-charge the pack down. Source: Medium storage guide.

Can I store LiPos in the fridge? No. A fridge brings moisture and condensation when the pack comes back out. A cool, dry room is enough, and a cold pack should return fully to room temperature before charging or use. Source: HobbyKing storage guide and Medium storage guide.

Is a slightly puffy pack still safe to use? No. Never use a LiPo that feels soft or has swollen. Retire it and dispose of it through a battery recycling point. Do not puncture it, press it flat, or charge it one more time. Source: Medium storage guide and DroneCamps storage guide.

How often should I check stored LiPo packs? Every two to four weeks, per the QRC storage guide. Source: QRC storage guide 19753.

Sources

Last updated: 2026-11-21

Low-Power ESP32 Battery Projects: Deep Sleep and Solar

A battery ESP32 project lives or dies on one number: average current. Get it right and a single 3000 mAh cell runs a field sensor for months. Get it wrong and the same cell is dead before dinner.

This guide covers the five power modes, every wake source, board-level sleep drain, battery sizing, solar sizing, and the mistakes that drain a pack in days. The sensor node build is covered in ESP32 Battery Sensor Node: Deep Sleep and Power Budget, and LiPo wiring in How to Power ESP32 and Arduino Projects on LiPo Power.

How long can an ESP32 really run on battery?

Battery life in hours equals usable battery capacity divided by average current. Average current is the awake share times the awake current, plus the sleep share times the sleep current. Source: ProjectECH; DroneBot Workshop; Hubble.

Take a node that wakes for 20 seconds at 180 mA and sleeps at 15 microamps, on one 18650 cell with a realistic usable capacity of 2400 mAh. Source: ProjectECH.

Report interval Average current Battery life from 2400 mAh
Every 10 minutes (180 x 20 + 0.015 x 580) / 600 = about 6.0 mA About 400 hours, about 16 days
Every 60 minutes (180 x 20 + 0.015 x 3580) / 3600 = about 1.01 mA About 2376 hours, about 99 days

Three lessons fall out of that table. First, the interval dominates: 60-minute reports give roughly 6 times the battery life of 10-minute reports. Second, sleep current matters: with a 5 mA sleep the 60-minute column collapses to about 17 days. Third, awake time is the other lever: Wi-Fi can spend 3 to 8 seconds just joining the network, so cut the awake window to 5 seconds. Source: ProjectECH.

Radios differ too: Wi-Fi transmit runs about 160 to 260 mA, BLE about 95 to 130 mA, and LoRa about 20 to 120 mA transmit with about 0.2 microamps in sleep. Source: ProjectECH; Hubble.

Which sleep mode does your project need?

The ESP32 has five power states. The figures below are chip-level typicals; your board will draw more. Source: DroneBot Workshop; Espressif sleep modes documentation.

Mode CPU and peripherals Radio Typical chip current What survives
Active On On or off 240 mA Wi-Fi transmit peak Everything
Modem sleep On Off between checks About 3 to 20 mA Everything, Wi-Fi association kept
Light sleep Paused Off About 0.8 mA RAM and registers, resumes where it stopped
Deep sleep Off Off About 10 to 25 microamps RTC memory only, 8 KB slow memory
Hibernation Off Off About 2.5 microamps Nothing guaranteed, not even RTC memory

Active is the normal running state; the only saving is lowering the CPU clock. Modem sleep turns the radios off between transmissions while the CPU keeps running, staying associated with the router by waking the radio on the DTIM interval. Light sleep pauses the CPU clock but preserves RAM and registers. Deep sleep powers down almost everything; only the RTC domain and optionally the ULP coprocessor stay alive. Hibernation is the deepest state: even the 8 MHz RTC oscillator and the ULP coprocessor are off, and RTC memory is not guaranteed. The only wake source is an EXT0 GPIO interrupt. Source: DroneBot Workshop.

What wakes the ESP32 from deep sleep?

The wake source defines the whole power profile. Source: ProjectECH; DroneBot Workshop; Hubble.

Wake source How it works Best for
Timer wake RTC timer fires after N microseconds Periodic sensing: wake, read, send, sleep
EXT0 wake One RTC GPIO goes high or low One event: a PIR motion sensor, a float switch, a door switch
EXT1 wake Any of several RTC GPIOs changes Several events at once
Touch pad wake A configured touch pad crosses its threshold A manual “report now” button on a sealed enclosure
ULP coprocessor Runs while the main CPUs sleep, about 150 microamps typical Wake the main CPU only on a threshold

Timer wake is the workhorse: call esp_sleep_enable_timer_wakeup(), then esp_deep_sleep_start(). EXT0 and EXT1 wake on a pin: EXT0 watches one RTC GPIO at one level, ideal for a PIR sensor, and EXT1 watches several. On the standard ESP32, RTC-capable GPIOs are 0, 2, 4, 12 to 15, 25 to 27, and 32 to 39. Touch wake uses the capacitive touch pins. The ULP coprocessor can poll an ADC channel or a GPIO while the main CPUs sleep and wake the main CPU only on a threshold. Source: ProjectECH; DroneBot Workshop; Hubble.

Always configure a wake source first, or the chip sleeps forever. Source: ProjectECH.

State survives deep sleep through RTC slow memory: variables declared with RTC_DATA_ATTR survive deep sleep, but not a power loss or a hard reset. Source: ProjectECH; TheLinuxCode; post 23387.

Why does your dev board never reach the datasheet sleep current?

The datasheet deep sleep figure is the bare chip. A dev board adds parts that draw current around the clock, and those parts dominate the sleep budget. Source: ProjectECH; DroneBot Workshop; post 23387.

A typical 30-pin DevKit board carries an AMS1117-3.3 linear regulator with a quiescent current of about 5 mA typical. With the USB chip, power LED, and pull-ups added, a “sleeping” dev board typically draws 5 to 15 mA. At 10 mA, a 3000 mAh cell lasts 300 hours, under two weeks. Source: ProjectECH; DroneBot Workshop.

Fix it in one of three ways: power the board through the 3V3 pin from an efficient external regulator; use a bare ESP32 module on a minimal breakout; or use a board designed for battery use. Measure the sleep current yourself first. Source: ProjectECH.

The XIAO boards stocked at QRC are the battery-friendly end of this scale, and the figures conflict across sources, so they are stated here as a sourced range, never as a single bench-tested number. Seeed’s wiki lists the plain XIAO ESP32S3 at 14 microamps in deep sleep, 2 mA in light sleep, and 27 mA in modem sleep. The XIAO ESP32S3 Sense with its expansion board attached is listed at 3 mA in deep sleep: the expansion board costs roughly 200 times the plain board’s sleep current, so detach it for a battery build and use the detachable camera only when the project needs it. The XIAO ESP32S3 Plus is listed at 33.51 microamps in deep sleep, and the XIAO ESP32C3 at 44 microamps. CircuitDigest measured a plain XIAO ESP32S3 board at 130 microamps in deep sleep, against a bare ESP32-S3 chip rating of 7 to 8 microamps. Plan with the worst figure in the range. Source: Seeed Studio XIAO ESP32S3 wiki; CircuitDigest; Embedded Nerd.

How do you size the battery?

Measure the build that will actually run from the battery. Source: UMA Technology; Hubble.

Step 1: measure each operating state. Record current in each state with a USB power meter, and use a multimeter in series with the battery lead for sleep. Source: UMA Technology; Hubble.

Step 2: calculate the average current. For each state, multiply current by time in that state, then sum and divide by the cycle time. Example: wake every 15 minutes, transmit for 5 seconds at 150 mA, sleep the other 895 seconds at 15 microamps. Average equals (5 x 150 + 895 x 0.015) / 900, which is 0.85 mA. Source: Hubble.

Step 3: divide capacity by average current, then derate. A 3000 mAh battery at 0.85 mA average gives about 3,500 hours, about 146 days. Now derate: usable capacity is about 70 to 80 percent of the label after aging, temperature, and self-discharge, so plan on about 2400 mAh usable from a 3000 mAh cell. Source: ProjectECH; Hubble; e-fm.tech.

Step 4: pick the chemistry. A standard LiPo at 3.7 V is workable for 6 to 12 month projects. A LiFePO4 cell at 3.2 V has low self-discharge around 3 percent per year, so it suits solar recharging. A CR2032 at 220 mAh suits only the lowest-power applications. Source: Hubble.

The biggest lever is the awake time: every second of Wi-Fi connect time at 150 mA costs as much as 150 seconds of sleep at 1 mA. Source: post 23387.

How do you size a solar panel for an ESP32 project?

A solar panel only has to replace what the board uses, plus the charging losses. Size it from the worst month, not the average: a panel sized for summer sun dies by mid-December. Source: Hubble solar sizing guide; e-fm.tech.

Step 1: daily energy. Daily energy equals average current times supply voltage times 24 hours. The 0.85 mA node at 3.7 V uses about 76 mWh per day. Source: Hubble solar sizing guide.

Step 2: battery autonomy. Size for three cloudy days: three days at 76 mWh per day is 228 mWh, or about 62 mAh at 3.7 V. Source: e-fm.tech; post 23188; post 15185.

Step 3: worst-month peak sun hours. Peak sun hours are the hours per day of full sunlight that would deliver the same energy as the real day. Look it up for your coordinates with PVGIS or NASA POWER, and use the worst month. Source: e-fm.tech.

Step 4: panel watts. Panel watts are about equal to daily energy divided by (charging efficiency times peak sun hours times a derating factor). The worked example comes out to about 0.021 to 0.11 W. In practice, fit a panel several times larger than the paper minimum. Source: e-fm.tech; Hubble solar sizing guide.

Step 5: charge controller. A small panel charging a single lithium cell needs a charger that terminates at 4.2 V and a protection circuit. The TP4056 module below charges a single cell from USB or a solar panel at up to 1 A. Standard lithium-ion and LiPo cells should not be charged below about 0 degrees C. Source: ProjectECH; e-fm.tech.

No solar panel is stocked at QRC as of 2026-11-21, so no panel is linked in this guide. The BirdBox build in Run a BirdBox Camera for Months on Solar Power shows the same pattern: panel in full sun, short cable, battery sized for three cloudy days.

How do you charge and protect the pack?

Charging, protection, and regulation are three separate jobs, and one module does not always do all three. The full wiring chain is covered in How to Power ESP32 and Arduino Projects on LiPo Power. Source: post 19087.

The TP4056 load-sharing trap. The TP4056 has no load sharing: it cannot tell current going into the battery from current drawn by your circuit. With the load on the battery terminals, the charger sees the load current as charge current, never detects the proper termination taper, and can keep pushing current into an already-full cell. Wire battery to B+ and B-, supply to IN+ and IN-, and take system power from OUT+ and OUT-. The proper fix is a load-sharing power-path circuit. Source: ProjectECH; post 19087.

The cutoff voltage has no single agreed number. Sources disagree on the per-cell cutoff, with figures from 3.0 V to 3.5 V per cell. This guide states that range and does not pick one number. Read the cutoff from the docs for the protection module and the battery you own, and wire the protection so it disconnects the pack from everything. The stocked 3000 mAh pack below has a built-in protection board. Source: post 19087.

What mistakes drain a battery pack in days?

  • Trusting the chip sleep figure for the whole board. The chip sleeps at 10 to 25 microamps; the board sleeps at milliamps. Measure the whole board.
  • Leaving Wi-Fi on between readings. A board that idles with Wi-Fi connected draws 35 mA or more. Sleep between readings.
  • Letting Wi-Fi join slowly, every cycle. Every awake second at 150 mA costs as much as 150 seconds of sleep at 1 mA. Use a static IP and cap retries at three.
  • Sizing the solar panel for summer. The panel must cover the worst month, not the average. Size from worst-month peak sun hours, and test through a cloudy week.
  • Never measuring the sleep current. Every battery estimate in this guide is arithmetic from stated inputs. Measure your own board’s sleep current and redo the math.

How do you fix a low-power project that dies too soon?

The board draws milliamps in deep sleep. Measure the board alone, then the regulator or converter alone. The likely causes are the power LED, the USB-to-serial chip, or a regulator with high standby draw. Power the 3V3 pin directly from a regulated 3.3 V supply, or remove the power LED where the board allows it. Source: DroneBot Workshop; post 23387.

The node boot-loops when the battery gets low. A nearly empty cell sags under a Wi-Fi transmit burst, and if the sag crosses the brownout threshold the chip resets mid-transmission. Treat 3.2 to 3.3 V under load as the effective empty point. The brownout fix is covered in ESP32-CAM Troubleshooting: Brownout and Camera Init Failed. Source: ProjectECH.

The battery voltage falls every week even with solar. The panel is too small for the worst month, the panel is shaded or flat, or the charge current never tapers. Check the battery voltage after the first week, and add panel size if it keeps falling. Source: post 23188; ProjectECH.

Which low-power setup fits your project?

Project Wake source Sleep mode Battery Solar
Temperature sensor, hourly reports Timer Deep sleep 3000 mAh 1S LiPo pack Not needed
PIR wildlife or BirdBox camera EXT0 on the PIR output Deep sleep 3000 mAh pack or larger Yes, worst-month panel
Always-on display or dashboard None, it must stay awake Modem sleep between updates USB power bank or mains No, the radio stays too busy
BLE beacon Timer, duty-cycled BLE scan Deep sleep between scans XIAO board with on-board charging Optional

Parts used in this guide

Prices and stock verified live on 2026-11-21. All four items below are in stock and purchasable.

Also verified live in stock: XIAO ESP32C6 1-Pack (ID 17835) $15.99 sale; XIAO ESP32-C5 1-Pack (ID 18380) $17.99 sale; XIAO ESP32S3 Sense 1-Pack (ID 17842) $32.49 sale, detachable camera; ESP32 DevKit V1, $9.99 sale; USB-C LiPo Module 1200mAh (ID 18959) $14.99 sale; HC-SR501 PIR (ID 14636) $5.99 sale; CellMeter8 (ID 3485) $19.99. No solar panel is stocked at QRC, so none is linked.

Shipped fast and securely from our secure facility in Queensbury, NY. QRC ships within the USA only.

Related guides

FAQ

How long will an ESP32 run on a battery? It depends on the average current, not the pack size alone. A node that wakes 5 seconds at 150 mA every 15 minutes and sleeps at 15 microamps averages about 0.85 mA, so a 3000 mAh battery gives about 146 days. Source: Hubble.

Why does my ESP32 use milliamps in deep sleep? The datasheet figure is the bare chip. The dev board adds a linear regulator with about 5 mA quiescent current, a USB-to-serial chip, and a power LED. Source: ProjectECH; DroneBot Workshop.

What wakes an ESP32 from deep sleep? The RTC timer for periodic work, EXT0 for one pin event such as a PIR sensor, EXT1 for any of several pins, a touch pad for a button, and the ULP coprocessor at about 150 microamps. Source: ProjectECH; Hubble.

How big a battery do I need for an ESP32 sensor? Work out the average current first, then divide capacity by average current, then derate to about 70 to 80 percent usable. Source: ProjectECH; Hubble.

Can I run an ESP32 on solar power? Yes. Work out the daily energy, size the battery for three cloudy days, look up the worst-month peak sun hours, and divide daily energy by charging efficiency times peak sun hours times a derating factor. Source: Hubble; e-fm.tech.

What is a safe cutoff voltage for a LiPo on an ESP32 project? No single cutoff voltage is universal: sources disagree, with figures from 3.0 V to 3.5 V per cell. Use a protected pack or a protection module, read the cutoff from its docs, and wire it so it disconnects the pack from all loads. Source: post 19087.

Sources

Last updated: 2026-11-21

Night FPV Cameras: Starlight, IR, and Low-Light Picks

A night FPV camera is not a day camera with the brightness turned up. It is a different sensor, a different filter, and a different set of settings. Pick the sensor first, check whether the camera can see infrared light, fit a fast wide lens, and set the OSD. The buying picks live in the companion guide linked below.

How does a starlight sensor see in the dark?

A starlight sensor is a CMOS sensor built to convert very few photons into a usable image. It is the first of three things that make a night camera different from a day camera. The name starlight is a marketing term, not a standard, so judge the sensor by its size, its pixel design, and its published sensitivity.

Back-illuminated pixels. In a back-illuminated sensor the light-sensitive area faces the lens directly, with the wiring behind it, so more of each pixel collects light. Starlight sensors in this class commonly use back-illuminated designs such as Sony STARVIS, named by UAVMODEL for the Ratel 2 and the Cat 3. Source: UAVMODEL.

Pixel size beats pixel count. A sensor with fewer, larger pixels collects more light per pixel, so a 1200TVL starlight camera can out-see a higher-resolution day camera at dusk. Source: Oscar Liang; IRLAB.

Gain, noise, and color. Night flying often pushes gain to 60dB or more. Oscar Liang notes that a good starlight sensor at 60dB of gain looks cleaner than a budget sensor at 40dB, and the Ratel 2 publishes a signal-to-noise ratio of 60dB with AGC off, per the Caddx spec sheet. As light falls, color goes first, so most night cameras switch to black-and-white. Source: Oscar Liang; Caddx spec sheet.

What does a lux figure actually mean?

Lux measures illuminance, the light falling on a surface. A camera lux figure, properly called minimum illumination, is the least light the camera needs to make a usable image. A lower number means the camera sees in less light. The number means nothing without the test conditions behind it.

How much light is out there. Make: Magazine puts real light levels in context: moonless overcast sky 0.0001 lux, moonless clear sky 0.002, full moon 0.27 to 1.0, civil twilight limit 3.4, full daylight 10,000 to 25,000. A 0.0001 lux camera claims moonless starlight. Source: Make: Magazine.

Why two lux figures cannot be compared directly. Makers measure minimum illumination under different shutter speeds, gain limits, lenses, and definitions of a usable image, so treat a lux figure as a starting point, not a ranking. IRLAB states the rule: a lower published figure indicates a more sensitive camera, provided the figures are quoted under comparable conditions. Source: IRLAB.

Lux vs sensitivity in mV/lux-sec. Some makers state sensitivity in millivolts per lux-second instead of lux: RunCam lists the Phoenix 2 SP V5 at 13,000 mV/lux-sec and the Night Eagle 3 at 11,390 mV/Lux-sec. A sensitivity figure and a lux figure cannot be ranked against each other. Source: post 13426, citing the RunCam manuals via Manuals+.

The only lux figures you can quote. State a lux figure only where the manufacturer published it: the Caddx manual rates the Ratel 2 at 0.0001 lux, and the Foxeer manual rates the Cat 3 at 0.00001 lux. Every other camera here states “not published”.

Camera Sensor Min illumination Source of figure
CADDXFPV Ratel 2 1/1.8-inch starlight 0.0001 lux Caddx manual
Foxeer Cat 3 (reference, not stocked) 1/3-inch CMOS 0.00001 lux Foxeer manual
Foxeer Micro Toothless 3 1/2-inch CMOS starlight Not published Foxeer publishes none
RunCam Phoenix 2 Nite 1/2.8-inch 2MP starlight Not published RunCam publishes none

Starlight or IR: which technology fits your flying?

Starlight amplifies the visible light already there, so it works at dusk, under streetlights, and in moonlight, with no extra hardware. Its limit is total darkness: under a moonless overcast sky with no streetlights, even the best starlight sensor runs out of photons. IR adds light the human eye cannot see, from an illuminator the camera reads. Source: UAVMODEL; Oscar Liang.

IR: bring your own light. An IR illuminator shines near-infrared light, usually at 850nm or 940nm, onto the scene. Oscar Liang built his IR torch from a 48-LED board costing about 8 US dollars, wired to a 3S balance plug and mounted on a GoPro mount. High-power IR units run 5 to 15W and 30 to 60g. Source: Oscar Liang; UAVMODEL.

850nm vs 940nm. An 850nm illuminator emits a faint red glow and cameras see it well; a 940nm illuminator is completely invisible but slightly worse, and it needs a camera with no IR-cut filter. For most pilots 850nm is the practical pick. Source: UAVMODEL.

The IR-cut filter decides everything. A camera can only use IR light if no IR-cut filter sits in the light path. There are four filter designs, and they behave very differently at night.

Filter design How it works Night behavior Example
No IR-cut filter Nothing blocks IR Sees IR light at all times RunCam Phoenix 2 Nite
Removable filter Filter lifts out for night mode Color by day, IR night with filter out CADDXFPV Gazer
Switchable IR-cut (ICR) Filter moves out in the dark Color by day, black-and-white IR night Day/night security-style cameras
Fixed IR-cut filter Filter always in place True color by day, blind to IR at night Most standard day FPV cameras

The Phoenix 2 Nite has no IR-cut filter at all, which is why it is the darkest-flying analog camera in stock. A fixed-filter camera will not see an IR illuminator no matter how bright it is, so check the filter before you buy the light. Source: post 13426; Oscar Liang.

Which lens should a night FPV camera use?

The lens decides how much light reaches the sensor and how much of the scene you see.

Lens choice What it does Night pick
Focal length Sets the field of view; shorter is wider and shows obstacles earlier 2.1mm, 165-degree FOV on the Ratel 2; the Nite is narrower at up to 125 degrees
Aperture (F number) Sets how much light gets in; lower F passes more light F1.0 on the Gazer, widest of any stocked night camera
M12 swap Most micro cameras use M12 threaded lenses, so the lens is replaceable Fit a 2.1mm M12 lens for a wider night view; keep it clean, since a smudged lens scatters streetlight like fog
IR-corrected lens A normal lens focuses visible light and IR at different points, so a day-sharp image goes soft under IR The Cat 3 ships with a large-aperture night-vision lens, per the Foxeer manual

Source: post 13426; Oscar Liang; Make: Magazine; Foxeer Cat 3 manual.

How do you set up a night camera in the OSD?

Most analog night cameras are tuned through an on-screen display menu, reached with the camera joystick or the OSD cable. Change one setting at a time so you know which change fixed the image. Source: UAVMODEL; Oscar Liang; Make: Magazine.

Setting Day value Night value Why it changes
Shutter / exposure Auto, fast Auto, max 1/30s or 1/25s Slower shutter lets in more light
Gain / AGC Low or auto Maximum auto gain Gain brightens the image; the cost is noise
2D noise reduction Off or low Medium to high Cuts grain at the cost of slight softening
3D noise reduction Off On where the camera has it Combines frames to cut noise
WDR On Off or low WDR amplifies noise in dark areas
Day / Night mode Color Auto, or black-and-white Black-and-white drops color noise and improves contrast
White balance Auto Fixed value Auto white balance swings color between lit areas

Step 1: shutter and gain. Set shutter to auto with a maximum exposure of 1/30s or 1/25s. Set the maximum gain as high as the camera allows, often 60dB or more. Accept the grain. Source: UAVMODEL; Oscar Liang.

Step 2: noise reduction. Set 2D noise reduction to medium or high, and 3D noise reduction on. 3D noise reduction combines frames, which cuts noise but creates slight ghosting on fast motion. Source: UAVMODEL; Caddx spec sheet.

Step 3: WDR, white balance, and color. Turn WDR off or low at night: it amplifies noise in dark areas and creates artifacts that look like obstacles. Fix the white balance to one value. Switch Day/Night to auto or straight to black-and-white. Source: UAVMODEL; Oscar Liang.

Step 4: check the power feed. A noisy power feed shows up as rolling lines in the video. Feed the camera from a clean 5V pad or a separate BEC where you can, and keep the camera signal wire away from motor wires and the VTX antenna. Source: post 13426.

What light level are you actually flying in?

Light level Ambient light What works What fails
Dusk 10 to 100 lux Any starlight camera, color mode A small day sensor
Streetlit park 1 to 10 lux Starlight camera, WDR low, B/W optional A day camera with a fixed IR-cut filter
Full moon, clear sky 0.27 to 1.0 lux Starlight camera, high gain, noise reduction on A 0.01 lux day camera
Moonless, clear sky 0.002 lux Starlight at max gain, or IR Any camera that needs 0.01 lux or more
Moonless, overcast 0.0001 lux IR plus a filterless camera Starlight alone, with no ambient light
Total dark, indoors Near zero IR plus a filterless camera Every visible-light camera

Ambient figures from the Make: Magazine lux table. Each step down needs a more sensitive camera or added light. With streetlights, a starlight camera is enough.

How do sensor size, TVL, and latency fit together?

Spec What it means at night What to buy on
Sensor size Bigger gathers more light, so the image holds up longer as light fades 1/2-inch (Toothless 3) or 1/1.8-inch (Ratel 2, Gazer, Moonlight kit); the Nite is 1/2.8-inch but has no IR-cut filter
TVL Analog horizontal resolution; matters least at night 1200TVL on most stocked analog night cameras, 1500TVL on the Nite and Gazer
Latency Analog runs about 20 to 26 ms and degrades gracefully; digital is sharper but a weak signal freezes or breaks up Fly analog for the live feed, record digital for the footage

Source: post 13426; Oscar Liang; IRLAB.

What mistakes ruin a night camera image?

  • Buying on the lux figure alone. Check the sensor size and the test conditions too.
  • Fitting a day camera and hoping the settings save it. No OSD setting adds photons the sensor never collected.
  • Leaving the IR-cut filter in place and buying an IR light. A fixed-filter camera cannot see IR light.
  • Mounting the IR panel next to the lens. IR light in the lens creates glare. Mount the panel on top of the quad, away from the lens. Source: Oscar Liang.
  • Leaving WDR on at night. WDR amplifies noise and creates artifacts that look like obstacles.
  • Flying a new spot, or flying fast, at night. Recon in daylight first, then slow down and add 50 percent extra clearance to every gap. Source: UAVMODEL.
  • Skipping the strobe and the buzzer. The strobe keeps the quad legal and visible; a self-powered buzzer finds it in the dark.

How do you fix a night image that is dark, noisy, or washed out?

Most night image problems are settings or power, not a bad camera.

The image is dark even at dusk. Check that Day/Night is set to Auto and not locked to Day. If the camera has an IR-cut filter, the filter is blocking the light you need in near darkness. Check the shutter maximum: if it is capped at 1/120s, raise it to 1/30s.

The image is noisy and grainy. Turn 2D noise reduction to medium or high, and 3D noise reduction on where the camera has it. Switch to black-and-white mode, which drops the color noise.

The image is washed out around lights. Set WDR off or low at night. Angle the camera down so streetlights sit at the top of the frame. Check for a light shining into the lens, including your own strobe or IR panel mounted too close.

The video has rolling lines or interference. The camera power feed is noisy. Move the camera power to a filtered 5V pad or a separate BEC, and keep the camera signal wire away from motor wires and the VTX antenna.

The camera switches between color and black-and-white on its own. Day/Night set to Auto can hunt when the threshold sits in the middle of your light level. Lock it to black-and-white for the flight. Source: Oscar Liang.

Which night camera should you buy for your flying?

Buy for the light level you fly in. The full per-use picks are in the companion buying guide, How to Choose an FPV Camera for Night and Low-Light Flying.

Dusk and streetlit flying, one camera for everything. Buy the CADDXFPV Ratel 2 (ID 20161) at $68.99 sale, $82.99 regular: the only manufacturer-published 0.0001 lux rating in stock, a 1/1.8-inch starlight sensor, and a 165-degree view from the 2.1mm lens. If the budget is tight, buy the Caddx Ratel 2 V2 (ID 13206) at $44.99 instead: same sensor, resolution, lens, and voltage range. Note: the two listings are the same camera model; keeping both is Alex’s call.

After dark, or flying with IR. Buy the RunCam Phoenix 2 Nite (ID 20157) at $104.99 sale, $126.99 regular. No IR-cut filter, 1500TVL, and automatic color to black-and-white switching. It is the darkest-flying analog camera in stock.

Dusk freestyle where sensor size matters most. Buy the Foxeer Micro Toothless 3 (ID 20159) at $89.99 sale, $108.99 regular. Its 1/2-inch CMOS sensor is the largest sensor on any stocked analog camera here. Foxeer publishes no lux figure for it.

Reference only, not stocked. The Foxeer Cat 3 (0.00001 lux per the Foxeer manual) is not stocked at QRC.

Parts used in this guide

Prices and stock were verified live on qualityrcparts.com on 2026-11-21. All four items below are in stock and purchasable.

Shipped fast and securely from our secure facility in Queensbury, NY. QRC ships within the USA only.

Related guides

FAQ

What is a starlight FPV camera? A starlight FPV camera uses a large, sensitive CMOS sensor built to make a flyable image in very low light. “Starlight” is a marketing term, not a standard, so judge it by sensor size and manufacturer-published sensitivity. Source: UAVMODEL; Oscar Liang.

What lux rating do I need for night FPV flying? For dusk and streetlit flying, a camera rated at 0.0001 lux, like the Ratel 2 per the Caddx manual, holds a flyable image. For moonless dark with no streetlights, no lux rating is enough on its own: you need an IR illuminator plus a camera with no IR-cut filter. Source: Caddx manual.

Can I compare two cameras by their lux figures? Only if the figures were measured the same way, and they rarely are. Use the lux figure as a starting point, then check sensor size and filter type. Source: IRLAB.

What is the difference between starlight and IR night vision? Starlight amplifies the visible light already in the scene and needs some ambient light. IR adds near-infrared light from an illuminator, which an IR-sensitive camera reads and the human eye cannot see. Source: Oscar Liang; UAVMODEL.

Should I use 850nm or 940nm IR light for FPV? Use 850nm for most flying: cameras see it well. 940nm is completely invisible with no red glow, but performance is slightly worse, and it needs a camera with no IR-cut filter. Source: UAVMODEL.

What OSD settings should I change for night flying? Set the shutter to auto with a maximum of 1/30s, raise the gain limit to maximum, turn 2D and 3D noise reduction on, turn WDR off or low, fix the white balance, and switch to black-and-white mode. Source: UAVMODEL; Oscar Liang.

Sources

Last updated: 2026-11-21

RC Boat Battery Guide: Best Battery for Your RC Boat

Match your boat’s cell count first, then pick capacity, C rating, plug, and size in that order. A boat battery lives in a sealed, hot hull, it can get splashed, and it is the heaviest thing on the boat, so it decides how the boat balances. Check your manual for the cell count, measure your battery tray before you buy, and match the plug before you order.

Which battery does my RC boat use?

Check the manual first. Boat makers set the battery, and the numbers are different from cars. The RC Ocean guide lists the common hobby-grade setups: small boats take one small 3S pack, mid-size boats take one 3S pack, and big boats take two matched packs.

Boat type Battery it usually takes
Small ready-to-run boat, 18 inch class One 3S 1300mAh 30C LiPo
Mid-size boat, 24 to 26 inch class One 3S 3200mAh 30C LiPo
Large boat, 36 to 42 inch class Two 4S packs, matched, for 8S
Dual-pack boat, Spartan class Two matched 3S packs for 6S
Small toy or beginner boat Maker’s own small pack, often 7.4V 1200mAh or 3.7V 800mAh

Never run a higher cell count than your ESC is rated for. Raising the voltage makes the boat faster, but heat and electrical load go up with it, so only do it if the motor, ESC, and wiring are rated for it. The RC Ocean guide gives the example of a boat rated to 4S maximum that should not run on 6S.

What types of RC boat batteries are there?

Five chemistries cover nearly every RC boat. Only LiPo and Li-ion are stocked as boat batteries at QRC.

Battery type Best for Main advantage Main limitation
LiPo Racing and brushless boats High power and low weight Needs careful use
Li-ion Small boats, spares Light, compact, steady power Lower C rating than LiPo
NiMH Beginners, casual use Easy and safe Heavy and less power
LiFePO4 Scale models Long life and safe Lower voltage per cell
Lead-acid Large scale boats Low cost per amp hour Very heavy

Source: Ufine battery guide comparison table, with lead-acid detail from Building Model Boats.

LiPo. LiPo batteries are the standard for fast RC boats: light, high current, and good with brushless motors. Packs are marked 2S, 3S, 4S, and more, where S means cells in series. A 2S pack is 7.4V, a 3S pack is 11.1V, and a 4S pack is 14.8V. Use a balance charger. Source: Ufine battery guide.

Li-ion. Li-ion packs are the small-boat spare. The RC Ratings guide lists 7.4V 1200mAh 2S 15C Li-ion packs built for small high-speed boats, and the QRC boat battery below is a 7.4V 600mAh Li-ion 2-pack.

NiMH. NiMH batteries suit beginners. They are heavier but easier to use, and they do not need balance charging. They give less power than LiPo, so they are not ideal for high speed. A NiMH cell is rated at 1.2V. Source: Ufine battery guide, Building Model Boats.

LiFePO4. LiFePO4 batteries are safer and last longer, but they have lower voltage per cell than LiPo. They suit scale boats. Source: Ufine battery guide.

Lead-acid. Lead-acid is heavy and is not common in small RC boats. It suits large displacement hulls such as tug boats, where the weight doubles as ballast. Sealed gel packs can mount in any orientation inside the hull. Source: Building Model Boats.

NiCad is left out on purpose. Building Model Boats notes NiCad is on its way out and advises beginners to avoid it.

How do I read a boat battery label?

Five numbers on the label decide whether the pack fits your boat.

Cells (S). 2S is 7.4V, 3S is 11.1V, 4S is 14.8V, and 6S is 22.2V. Match the ESC. Source: RC Ocean guide.

Capacity (mAh). Run time. Most boat packs run 1500 to 6000mAh. Small boats use 1500 to 3000mAh, and medium to high-speed boats use 4000 to 6000mAh. Source: RC Ocean guide, Ufine battery guide.

C rating. How fast the pack can deliver current. Maximum continuous current equals capacity in amps times the C rating. A 5000mAh 50C pack can deliver 5 times 50, or 250A. Use 30C or more for brushless boats, and 50C or more for performance boats. Source: RC Ocean guide, Ufine battery guide.

Connector. IC3, IC5, EC5, XT60, XT90, T connector, or Traxxas iD, plus the small SM-2P and SM-5P plugs on small boat packs. Match your boat, or buy an adapter.

Size and case. The pack must fit the tray and keep the boat balanced. Hard cases protect cells in impacts. Soft case packs are lighter. Source: RC Ocean guide.

How much run time will a bigger battery give?

A bigger battery gives more run time, but no fixed number of minutes applies to every boat. Run time depends on the hull, the motor, and how much throttle you use, so this guide gives no run time in minutes for any specific boat or pack. Ufine gives a method to estimate it: estimated run time in minutes equals battery capacity in amp hours divided by average current draw in amps, times 60, times 0.8, where the 0.8 factor adds a safety margin. Its worked example is a 5000mAh pack at 25A average draw: 5 divided by 25, times 60, times 0.8, which is about 9.6 minutes. That example is arithmetic, not a measured result. A bigger pack also weighs more, so the longest run time on paper is not always the fastest boat on the water, and a pack that is too small for the motor’s draw will run hot and sag under load.

Will a car LiPo battery work in an RC boat?

Often yes, if the cell count, plug, and size match. The RC Ocean guide answers this directly: a car pack works in a boat when those three match, and the pack must fit the tray and keep the boat balanced. That is why the Parts block below includes 3S LiPo packs sold for cars and planes alongside the one dedicated boat battery. A T connector pack does not plug into an EC5 boat without an adapter, and shorty packs at about 75 mm long fit trays a full-size pack will not.

What plug and size fit my boat?

Measure before you buy: tray length, width, and height, plus the hatch opening, since a pack that fits the tray but not the hatch is useless. Check the plug on your boat against the plug on the listing, and check the wire direction.

Small boats with SM plugs. The QRC boat battery (ID 18619) uses the black SM-2P 2-pin plug and fits H100, H102, H106, H108, and H120 boats, plus Q2, Q3, and Q7 series boats that use the same battery. It measures 38 x 36.5 x 18.5 mm, and two SM-2P to male mini Tamiya adapter cables are included. The listing warns that some newer boat versions use a different plug, so check your plug before ordering. The RC Ratings guide lists the same pattern on other small boats: 7.4V 1200mAh packs with SM-5P plugs for R208 and R308 boats, and SM-2P plugs on H101, H103, and H105 boats. Same voltage does not mean the same plug.

Hobby boats with T, EC, and XT plugs. Hobby-grade boats use the same plugs as cars: T connector, EC3, EC5, XT60, and XT90. The 3S packs in the Parts block use a T connector, and the shorty packs measure about 75 mm long, which fits compact trays. If your boat uses EC5 or XT90, buy the pack with that plug rather than adapting a T connector pack.

Bay fit and balance. The battery is the heaviest thing on the boat, so where it sits decides how the boat balances. Fix the battery in place so it cannot move during use: the Ufine checklist lists this as a pre-run check, since a loose battery shifts the boat’s balance. If the pack can slide, add a strap or a foam block to hold it, and check the fit again after the first run.

Do I need two batteries for a big boat?

Big boats use two packs wired together, and the two packs must match. For most owners, two 3S 11.1V packs work better than a single 6S pack. Match them on the same capacity, C rating, connector type, and use history. Source: RC Ocean guide, CNHL guidance quoted there.

Buy the pair together when you can, and keep them together: charge, run, and store them together, so their use history stays matched. Do not pair a new pack with an old pack, and do not pair packs of different capacities. If one pack in a matched pair swells or fails, replace the pair, not just the failed pack. For small boats, a second pack is a spare, not a pair: it doubles your time on the water, so buy the same model as the pack your boat came with.

How do I keep a boat battery dry?

A boat battery lives where water is, so sealing and drying matter more than on any other RC model. No stocked QRC boat battery listing publishes a waterproof rating, so this guide claims none. Keep the pack sealed and dry, take it out after the run, and dry the compartment. Source: RC Ocean safe battery habits.

After every session, take the pack out of the hull as soon as the boat is back on shore. Dry the compartment, the pack, and the connectors: a wet connector corrodes and a corroded connector runs hot. Never charge a wet pack: let it dry fully first, and never charge a swollen pack. Check the hatch seal before the next run, since a worn seal is how water gets in. Keep the leads routed clear of the prop shaft and the hatch edge. Before the run, check the pack for damage or swelling, make sure the connectors are tight, fix the battery in place, and set the ESC low-voltage cutoff for LiPo. Source: Ufine pre-run checklist.

How do I charge a boat battery?

Charge it like any LiPo, with one boat difference: let it cool first. A pack that just came out of a sealed, hot hull is warm, so let it cool to room temperature, dry it if it is wet, then balance charge it.

Balance charge every LiPo pack: connect the main lead and the balance lead to a LiPo balance charger, set LiPo balance mode, match the cell count to the label, and stay in the room until it finishes. Never use a NiMH charger for a LiPo pack. Never leave a charging battery unattended. The full step-by-step, with the per-cell voltage table and the 1C charge current rule, is in the QRC charging guide linked below, and this guide does not repeat its tables. For storage, store LiPo packs at 3.7V to 3.85V per cell, in a cool, dry place, and do not store them fully charged. Source: Ufine battery guide.

What are the common mistakes?

  • Running a higher cell count than the ESC allows. Check the ESC rating first.
  • Buying on mAh alone. High mAh adds weight, and extra weight can reduce speed and upset the balance.
  • Ignoring the C rating. Use 30C or more for brushless boats, and 50C or more for performance boats.
  • Buying the wrong plug. Same voltage does not mean the same plug.
  • Skipping the tray measurement. A pack that does not fit the tray or the hatch is a return, not a run.
  • Using the wrong charger. LiPo needs a balance charger, NiMH needs a NiMH charger. Never mix charger types.
  • Forgetting water protection. Dry the compartment after the run, and never charge a wet pack.
  • Leaving a LiPo fully charged in storage. Store at 3.7V to 3.85V per cell, in a cool, dry place.

How do I fix a boat battery problem?

The boat is slow on a new pack. Check the cell count first: a 2S pack in a 3S boat runs slow by design. Then check the C rating and that the plug is fully seated.

Run time dropped sharply. Check the pack for swelling or damage, and do not charge a damaged pack. Check the connectors for corrosion from a wet run.

The pack is hot after a run. A hot pack is working too hard. Check that the C rating covers the motor’s draw and that the cell count matches the ESC rating. Let it cool before charging.

The boat handles differently than it did. The battery moved. A loose battery shifts the boat’s balance, so fix the pack in place and check the tray fit.

The pack got wet. Take it out, dry it and the compartment, and let it dry fully before charging. If the pack is swollen, punctured, or smells odd, stop using it. Never charge a wet or swollen pack. Source: RC Ocean FAQ, Ufine checklist.

One pack in a dual setup runs hotter than the other. The pair is mismatched. Check that both packs have the same capacity, C rating, connector, and use history.

Which battery should I buy for my boat?

Small boat with an SM-2P plug, H100 to H120 class. Buy the 7.4V 600mAh Li-ion RC Boat Battery, 2 Pack (ID 18619) at $28.99 on sale, $34.99 regular. It is the only dedicated boat battery stocked at QRC at the time of writing, and it fits H100, H102, H106, H108, and H120 boats. Match your plug before ordering: some newer boat versions use a different plug.

Mid-size speedboat on 3S with a T connector. Buy the OVONIC 3S Short LiPo Battery, 2200mAh, 120C, 11.1V (ID 19386) at $26.99 on sale, $32.99 regular. The listing states it fits boats with a matching connector, and at 75.14 x 33.49 x 25.87 mm it fits compact trays.

Mid-size boat on 3S where a shorty pack fits better. Buy the Zeee 3S LiPo Battery, 2200mAh, 50C, 11.1V, Shorty, T Connector, 1-Pack (ID 19979) at $23.99 on sale, $28.99 regular. Same 2200mAh and 50C as the standard pack below, at 75 x 34 x 26.5 mm.

First 3S spare, standard size. Buy the 3S LiPo Battery, 2200mAh, 50C, 11.1V, T Connector (ID 18815) at $25.99 on sale, $31.99 regular. It measures 105 x 33 x 20 mm and weighs 179 g.

Big boat on 6S or 8S. Buy two matched packs, not one large pack, and size them from the 6S guide linked below. Read post 23568 before ordering.

Parts used in this guide

Prices and stock were verified live on qualityrcparts.com on 2026-11-21. All four items below are in stock and purchasable. Only one dedicated boat battery is stocked at QRC at the time of writing (ID 18619); the other three are 3S LiPo packs whose listings state they fit boats with a matching connector.

Shipped fast and securely from our secure facility in Queensbury, NY. QRC ships within the USA only.

Related guides

FAQ

What battery does my RC boat use? Check the manual. Small boats use one small 3S pack, mid-size boats use one 3S pack, and large boats use two matched packs. Source: RC Ocean FAQ.

Can I use a car battery in an RC boat? Often yes, if the cell count, plug, and size match. Source: RC Ocean FAQ.

How many mAh do I need for an RC boat battery? Most RC boat batteries range from 1500mAh to 6000mAh. Small boats use 1500mAh to 3000mAh, while medium or high-speed boats use 4000mAh to 6000mAh. Source: Ufine FAQ, RC Ocean FAQ.

What C rating should I buy? Use 30C or more for brushless boats, and 50C or more for performance boats. Source: RC Ocean FAQ.

Can I run a 4S pack in a 3S boat? Only if the ESC and motor are rated for it. Higher voltage means more heat and load. Source: RC Ocean FAQ, Ufine FAQ.

Is LiPo better than NiMH for RC boats? LiPo is better for speed and power-to-weight ratio. NiMH is better for simple use and beginner charging. Source: Ufine FAQ.

How should I store RC boat LiPo batteries? Store at 3.7V to 3.85V per cell in a cool, dry place. Do not store them fully charged. A fire-resistant LiPo bag or metal box can improve safety. Source: Ufine FAQ.

Sources

Last updated: 2026-11-21

How to Charge a LiPo Battery: Balance Guide

To charge a LiPo battery, balance charge it: connect the main lead and the balance lead to a LiPo balance charger, set LiPo balance mode, match the cell count to the label, set the charge current to 1C, and stay in the room until every cell reads 4.20V. A 2200mAh pack charges at 2.2A at 1C, and a 5000mAh pack at 5A. Put the pack in a LiPo safe bag on a non-flammable surface first, and never charge a swollen, punctured, or hot pack. If you will not fly for more than a few days, use the charger storage mode instead of leaving the pack full.

What are the numbers that run every LiPo charge?

Every LiPo decision comes down to voltage per cell. A standard LiPo cell is 3.7V nominal, 4.20V when fully charged, and about 3.8V at storage voltage, the commonly cited figure, with several published guides giving a 3.80 to 3.85V range. Multiply the per-cell figure by the number of cells.

Pack Nominal (3.7V) Full (4.20V) Storage (about 3.8V) Minimum (about 3.0V)
1S 3.7V 4.2V About 3.8V About 3.0V
2S 7.4V 8.4V About 7.6V About 6.0V
3S 11.1V 12.6V About 11.4V About 9.0V
4S 14.8V 16.8V About 15.2V About 12.0V
6S 22.2V 25.2V About 22.8V About 18.0V

Three rules follow. Never charge a standard LiPo cell past 4.20V. Never run a cell below about 3.0V: cells run that low are damaged, and many chargers will refuse them. And the cell count on the charger must match the label: a 3S pack charged on a 4S setting is pushed toward 4S voltage. Sources disagree slightly on the exact storage figure and on the low-voltage floor, from 3.0V to 3.5V per cell, so follow the battery maker docs for your pack.

The other number is the charge rate, or C rate. 1C means a charge current in amps equal to the pack capacity in amp-hours: divide the capacity in mAh by 1,000. A 650mAh pack charges at 0.65A at 1C, a 2200mAh pack at 2.2A, and a 5000mAh pack at 5A. 1C is the safe default every published guide in the Sources list agrees on. Charge slower than 1C when the pack is old, has drifted cells, or sat unused for months. Charge faster than 1C only when the battery maker prints a higher charge rate on the label.

What gear do you need before you plug in?

Four items cover a first charging setup. The charger matters most: it must be a LiPo balance charger, not a NiMH or NiCd charger, which follows a different charging method and will damage a LiPo pack or overheat it. A balance charger has a balance port in addition to the main output, and it reads each cell through the balance lead while it charges.

  • A LiPo balance charger that covers your cell counts. A 2S and 3S only charger cannot charge a 4S or 6S pack.
  • The right leads. The main lead carries the full charge current, so it needs the plug that matches your pack, usually XT60 or XT30. The balance lead is the small multi-pin plug that lets the charger see each cell. If the balance lead is too short, or the plug does not match the charger port, use an adapter lead from the adapter-cable guide linked below.
  • A LiPo safe bag. Charge in a LiPo bag or fireproof container, on a non-flammable surface.
  • A cell checker. It reads each cell through the balance lead before you charge, so a weak cell shows up before current flows.

Do not charge with a phone charger or a USB power brick: a general USB charger has no balance port, no cell-count check, and no LiPo cutoff. The only USB option is a proper single-cell lithium charging module, such as the TP4056 module in the charger-choice guide.

How do you balance charge a LiPo, step by step?

Balance charge in this order every time: the charger must see the right cell count before current flows.

  1. Let the pack cool. After a run, wait until the pack is at room temperature: never charge a hot pack or a frozen or very cold pack.
  2. Inspect the pack. Do not charge a swollen, hot, leaking, punctured, or crushed pack. Check the balance lead wires and plug for damage.
  3. Put the pack in the safe bag. Set the bag on a non-flammable surface and put the pack inside, leads out where you can reach them.
  4. Read the label. A 3S 2200mAh pack is three cells and 2200mAh, so 1C is 2.2A.
  5. Connect the main lead. Red goes to positive, black goes to negative.
  6. Connect the balance lead. Plug it into the charger balance port, in the socket that matches the cell count. A 4-pin plug goes in the 3S socket, not the 4S socket. Never force a plug that does not fit.
  7. Set the charger. Select LiPo balance mode, not plain charge or fast charge, and enter the cell count and the charge current from step 4.
  8. Check the display. The charger should show the same cell count you entered and a voltage per cell for every cell. If it shows fewer cells, or a cell reads 0.00V, stop.
  9. Start the charge and stay in the room. The pack and the leads should stay cool, and the cell voltages should climb together. If a cell climbs much faster than the rest, or the pack gets warm, swells, or smells, stop.
  10. Stop when the charger reports full. Every cell should read 4.20V, or within about 0.03V of it. Unplug the balance lead first, then the main lead.

Plan on about 2 to 3 hours from empty at 1C for a complete balance charge, including the saturation stage where the cells equalize. The pack reaches about 70 percent in the first stage, and the saturation stage takes the rest of the time. A pack that finishes in minutes was nearly full already, or the charger cut off early on a fault.

What charge rate do you use?

Use 1C unless the battery maker states otherwise.

Pack capacity 1C charge current 0.5C charge current
650mAh 0.65A 0.33A
1300mAh 1.3A 0.65A
2200mAh 2.2A 1.1A
5000mAh 5.0A 2.5A

Two limits bind before the current limit does. The first is the charger wattage: charging power is roughly pack voltage times charge current, so a 3S 2200mAh pack at 1C needs about 24W, while a 6S 5200mAh pack at 1C needs about 115W. An 80W charger can deliver 1C to the small pack but not to the big one: it will simply deliver less current and take longer, which is the wattage limit, not a fault. The second limit is the pack label: if it prints a maximum charge rate, that is the ceiling. If it prints no charge rate, stay at 1C.

What do the charger modes do?

Most balance chargers offer the same five modes.

Mode What it does When to use it
Balance charge Charges the pack and equalizes each cell to 4.20V Every normal charge
Charge (no balance) Charges through the main lead only Avoid for multi-cell packs
Fast charge Ends the charge early When time matters more than the last few percent
Storage Brings the pack to about 3.8V per cell Packs that will sit for days
Discharge Drains the pack slowly Before disposal

Plain charge without the balance lead is the mode to avoid: the charger sees only the pack total, so it can stop while one cell sits over 4.20V and another sits under it. Fast charge saves minutes and costs pack life, because it skips the stage where the cells are evened out.

How do you storage charge a pack?

A pack that will sit for more than a few days goes to storage voltage, about 3.8V per cell, the commonly cited figure; several published guides give a 3.80 to 3.85V range. A pack left full at 4.20V per cell for weeks degrades faster, and a pack left flat degrades faster still.

Storage mode works in both directions: it charges a flown pack up, and it discharges a full pack down to it. Run storage mode after every session for packs you will not use within a day or two, and check stored packs every few weeks. For the full storage routine, read the storage guide linked below.

How do you charge a LiPo for the first time?

New packs usually arrive at roughly storage voltage. Before the first run, balance charge the pack at 1C or less, then check that all cell voltages ended within a few hundredths of a volt of each other. A new pack with one cell far off the others is worth reporting to the seller. There is no break-in ritual that a normal balance charge does not cover. Keep the first runs gentle. Do the same for any pack that sat unused for months: charge it at 0.5C the first time back, and retire it if one cell will not hold voltage after balancing.

What about LiHV and LiFe packs?

LiHV and LiFe packs are not standard LiPo packs, and they need their own charger settings. LiHV cells charge to 4.35V per cell instead of 4.20V and need the LiHV setting; charging a normal LiPo on it overcharges it. LiFe cells use their own setting with a full voltage of about 3.6V per cell. Always check the label: the chemistry is printed on the pack, and the setting must match it.

Can you charge more than one pack at once?

Yes, on a parallel balance board, if every pack follows three rules: same cell count, voltages within 0.1V per cell of each other before you connect anything, and charge current set for the combined pack. Six 1300mAh packs in parallel are one 7800mAh pack, so 1C is 7.8A total. Always use balance mode on a parallel board, never fast charge, and stay in the room. Use a fused board. The full rules are in the adapter-cable guide linked below. Parallel charging is not a beginner technique: if you cannot read each cell on every pack with a checker first, charge the packs one at a time.

What mistakes ruin packs or start fires?

Most LiPo fires trace to a small set of avoidable mistakes.

Mistake What happens Fix
Charging on NiMH or NiCd mode Wrong voltage curve, overcharges the pack Always select LiPo balance mode before you start
Wrong cell count on the charger Charger pushes a 3S pack toward 4S voltage Match the display to the label before you press start
Charging through the main lead only Charger cannot see single cells, cannot balance Connect the balance lead every time
Leaving a charge unattended A fault burns unchecked Stay in the room for the whole charge
Charging a swollen or punctured pack Damaged cell vents or catches fire Retire the pack, never charge it
Charging on a flammable surface A fault has fuel at once LiPo safe bag on a non-flammable surface
Storing packs full for weeks Cells degrade at full voltage Storage charge to about 3.8V per cell when the pack sits

Charging on NiMH mode is the classic beginner error: the charger pushes current with the wrong cutoff, and the pack has no protection against it. Leaving a charge unattended turns every other mistake into a fire: a fault caught in the first minute is a ruined pack, while the same fault caught an hour later is a burned bench.

Why is my charger showing an error or a low cell?

Work through the cause in order, cheapest check first.

The charger shows fewer cells than the pack has. The balance lead is not fully seated, or it is in the wrong socket. Reseat the plug on both ends, and check that a 4-pin plug is in the 3S socket. Try the pack lead directly into the charger, skipping any adapter: if the cell count comes back, the adapter is the fault.

One cell reads much lower than the rest. Cells drift with age and use. Run a full balance charge at 0.5C and check again. If one cell stays far off after balancing, retire the pack.

The charger reports a low-voltage error and will not start. One or more cells dropped below the safe level, typically about 3.0V per cell. The pack was run too flat, left plugged in, or stored flat. Do not force it by charging on NiMH mode: that bypasses the safety cutoff that refused the pack for a reason. If a cell reads 0.00V, the pack is done. Retire it and dispose of it following local rules.

The pack gets hot or swells during charging. Stop the charge at once. Move it outdoors on a non-flammable surface if it is safe to do so, and keep people away. A puffed LiPo is a fire risk: do not charge it, recover it, or use it.

Which charger setup should you buy?

Buy for the packs you own. Four profiles cover most pilots.

First RC car or plane, 2S and 3S packs only. Buy the ImaxRC B3 Pro Balance Charger (2S/3S) (ID 16863) at $15.99. Treat it as a starter: the moment you add a 4S pack, you need a charger that covers 4S.

Small bench work, single cells. Buy the TP4056 5V Micro USB 1A Lithium Battery Charging Module (ID 16875) at $1.49, or the 5-pack (ID 83) at $1.99. It charges one lithium cell at 1A and must never be used to charge a series pack.

FPV fleet, 1S to 6S packs, one charger. Buy the B6 80W Mini LiPo Balance Charger and Discharger with Power Supply (ID 18960) at $42.99 on sale (regular $51.99). It covers 1 to 6 cells, includes the power supply, and takes XT60, JST, and T connectors. Add the 3-in-1 Battery Voltage Checker Balancer and Discharger (ID 12052) at $12.49 to read each cell before every charge.

Big 6S packs at full 1C. Buy the B6neo 2 Smart Charger, DC 300W / PD 80W (ID 7225) at $84.99 for the US Plug variation. A 6S 5200mAh pack at 1C needs about 115W, past an 80W input, so plan on the 300W DC input for big packs; the PD input at 80W covers small packs. A Blue variation is also listed at $99.99.

Add a LiPo safe bag before any of it if you do not already own one: the Zeee Small LiPo Safe Bag, Fireproof Pouch, 11 x 8.7in (ID 20106) is $11.99 on sale (regular $14.99). If your balance lead is short or the plug does not match your charger port, add the JST-XH balance extension leads from the adapter-cable guide below.

Parts used in this guide

Prices and stock were verified live on 2026-11-21. All five items below are in stock and purchasable.

Shipped fast and securely from our secure facility in Queensbury, NY. QRC ships within the USA only.

Related guides

FAQ

How long does it take to charge a LiPo battery? About 2 to 3 hours from empty at 1C for a complete balance charge, including the saturation stage where the cells equalize. The pack reaches about 70 percent in the first stage. A pack that finishes in minutes was nearly full already. Source: Battery University BU-409.

Can I charge a LiPo battery without a balance charger? You can charge through the main lead only, but the charger cannot see single cells that way, so it cannot balance them. One cell can end up overcharged while the pack total looks right. Source: EuroRC charging guide and SwellRC charging guide.

What is the storage voltage for a LiPo battery? About 3.8V per cell, with several published guides giving a 3.80 to 3.85V range. A 3S pack stores at about 11.4V. Use the charger storage mode. Source: SwellRC charging guide, FPV Bible charging guide, and Tech1RC safety guide.

Can I leave a LiPo battery charging overnight? No. Charge only when you can watch it, and store packs at storage voltage instead of keeping them full. Source: SwellRC charging guide and EuroRC charging guide.

What do I do if one cell is below 3.0V? Stop. Do not force it by charging on NiMH mode. Most chargers refuse to start below about 3.0V per cell, and a cell that reads 0.00V means the pack is done. Retire it and dispose of it following local rules. Source: HobbiesDirect not-charging guide and SwellRC charging guide.

Can I charge a LiPo battery with a phone charger? No. A general phone charger or USB power brick has no balance port, no cell-count check, and no LiPo cutoff. The only USB option is a proper single-cell lithium charging module, such as the TP4056 module. Source: QRC charger-choice guide and MakeUseOf charging guide.

How do I know my LiPo battery is fully charged? Every cell should read 4.20V, or within about 0.03V of it. Check the per-cell display, not just the pack total. Source: QRC adapter-cable guide and SwellRC charging guide.

Sources

Last updated: 2026-11-21