OV2640 NoIR Night Vision Camera Module for BirdBox Builds

OV2640 NoIR night vision camera module for a BirdBox camera

OV2640 NoIR Night Vision Camera Module for BirdBox Builds

A BirdBox is dark inside. That is the whole problem with putting a normal camera in one. The standard OV2640 module on an ESP32-CAM or ESP32-S3-CAM board has a 650nm IR-cut filter built into the lens holder. That filter blocks infrared light and gives true color in daylight. Inside a closed nest box, there is no daylight, and the filter blocks the only light that would let the camera see. The picture stays black.

The fix is the NoIR version of the same 24-pin OV2640 module. NoIR means no IR-cut filter. The sensor itself is IR-sensitive once the filter is out, so with 850nm IR illumination in the box, the camera sees in the dark. This guide explains what the NoIR module is, why the standard module fails in a BirdBox, and what you need to make night vision work.

What a NoIR module is

The NoIR module uses the same OV2640 sensor as the standard module: 2MP, 1600×1200 UXGA, JPEG, YUV, and RGB output. The difference is the lens holder. On the standard module, a 650nm IR-cut filter sits in front of the sensor. On the NoIR module, that filter is not there. The sensor sees visible light and infrared light, including 850nm IR from an illuminator.

The module in the store is the OV2640 NoIR Night Vision Camera Module, 850nm, 160-Degree Wide Angle, 24-Pin DVP for ESP32-CAM ($22.99). It has a 160-degree wide-angle lens, a 24-pin DVP connector, a 21mm FPC cable, and it runs on 2.8V. It drops into the same camera socket as the standard OV2640 module, so it fits ESP32-CAM and ESP32-S3-CAM boards with a 24-pin DVP camera connector, including the ESP32-S3-CAM N16R8.

Why the standard module fails in a dark box

A standard OV2640 module is built for daylight. The IR-cut filter passes visible light and blocks infrared. In daylight, that gives true color. In a dark nest box, there is no visible light to pass. An 850nm IR illuminator will not help either, because the filter blocks the IR light before it reaches the sensor. The result is a black frame, no matter how much IR light you add.

The NoIR module has no filter in the way. The same 850nm IR light reaches the sensor, and the camera produces a usable night image. That is the only change that matters for a BirdBox: the filter is gone, so IR light gets through.

The pink tint trade-off

A NoIR module is a night and IR setup, not a true-color daytime setup. Without an IR-cut filter, daytime images have a pink or purple tint, because the sensor is seeing infrared light along with visible light. If your box gets daylight through the entrance hole, daytime shots will look tinted.

That is normal for any NoIR camera, and it is the trade to accept for night vision. If you want true-color daytime only, keep the standard OV2640 module with the 650nm IR-cut filter. If you want to see inside a dark box at night, use the NoIR module and accept the tint in daylight. You cannot have both from one module.

What you need besides the module

The NoIR module sees infrared light, it does not make its own. You need 850nm IR illumination in the box. The module does not include an IR light, so add your own 850nm IR illuminator or IR LED array. Place it so it lights the nest area without shining straight into the lens.

You also need a board to plug the module into. The ESP32-S3 Development Board with OV2640 Camera, Dual-Core 240MHz, WiFi + Bluetooth 5 LE, 45 GPIOs ($22.99) takes the module in its 24-pin DVP socket. If your board already has a standard OV2640 fitted, swap the module: lift the old one out of the socket and seat the NoIR module in its place, FPC contacts facing the right way, then power the board and check the stream before you mount anything.

A microSD card for local recording is worth adding. The ESP32-S3-CAM boards record to SD, so you can keep clips even when WiFi drops. Check the board pinout before you wire anything else, and see the ESP32-S3-CAM guide for camera project basics.

Quick facts

Fact Value
Sensor OV2640, 2MP, 1600×1200 UXGA
Night vision NoIR, no IR-cut filter, sensitive to 850nm IR
Lens 160-degree wide angle
Interface DVP, 24-pin, 0.5mm FPC, 21mm cable
Voltage 2.8V
Fits ESP32-CAM and ESP32-S3-CAM with 24-pin DVP connector
Price $22.99

How to swap in the NoIR module

  1. Power the board off and remove it from the box.
  2. Open the camera socket latch and lift the standard OV2640 module out.
  3. Seat the NoIR module in the socket, FPC fully in and straight, then close the latch.
  4. Power the board and open the camera stream in daylight first. Expect a pink or purple tint. That confirms the filter is gone.
  5. Turn the room lights off, switch on your 850nm IR light, and check the stream again. The image should come back in black and white IR.
  6. Mount the board and IR light in the box, then test once more with the lid on.

Parts that fit this guide

Prices below are the live store prices verified November 19, 2026. In-stock parts ship from New York in 1-2 business days.

OV2640 NoIR Night Vision Camera Module, 850nm, 160-Degree Wide Angle, 24-Pin DVP for ESP32-CAM ($22.99)

NoIR OV2640 2MP camera module with 850nm night vision, 160-degree lens, and 24-pin DVP. Drop-in night-vision upgrade for ESP32-CAM and ESP32-S3-CAM boards.

ESP32-S3 Development Board with OV2640 Camera, Dual-Core 240MHz, WiFi + Bluetooth 5 LE, 45 GPIOs ($22.99)

ESP32-S3 camera board with OV2640 2MP camera, dual-core 240MHz, 45 GPIOs, WiFi plus Bluetooth 5 LE, and USB OTG. The board the NoIR module plugs into.

Shop the full range in the ESP32 and ESP8266 category at Quality RC Parts. See also: ESP32-S3-CAM vs ESP32-CAM board comparison.

Frequently asked questions

Does the NoIR module fit my ESP32-S3-CAM board?

Yes, if your board has a 24-pin DVP camera connector. It drops into the same socket as the standard OV2640 module, including on the ESP32-S3-CAM N16R8.

Do I need extra light?

Yes. The module sees infrared light, it does not make its own. Add 850nm IR illumination in the box for night vision.

Will daytime images look normal?

No. Without an IR-cut filter, daytime images have a pink or purple tint. Use the standard IR-cut OV2640 module for true-color daylight.

Is the NoIR module more expensive than the standard module?

No. The NoIR module is $22.99, and the standard 120-degree OV2640 module runs about the same price. There is no real price penalty for night vision, you just need 850nm IR light in the box.

Last updated: November 19, 2026.