Filament Refill Spool Adapter Guide: Fit and Load

A filament refill spool adapter lets a spool-less coil of filament ride on a spool it was not made for. A refill is filament wound as a coil with no spool included. It costs less per kilo than the same filament on a spool, but it cannot print until it sits on something that holds its shape and keeps it centered. When they come from different systems, the adapter is the bridge.

This guide covers what an adapter does, the four adapter types, how to check the fit, and how to load a refill without tangles. For which filament to print RC and drone parts with, read PLA vs PLA+ vs PETG: Pick the Right 3D Printer Filament for Drone Parts. For refill prices and break-even math, read Filament Refill vs Spool: How Anycubic Refills Save You Money.

What does a filament refill spool adapter do?

A refill coil is a wound roll of filament held together by straps or tape, with a hollow center and no flanges. On its own it cannot mount on a printer or feed at a steady tension. A reusable spool gives it flanges to contain the sides, a hub to center the coil, and a lock to hold the two halves together.

An adapter does one of three jobs. It changes the hub size, filling the gap between the refill core and the spool hub so the coil sits centered. It changes the locking interface, carrying the notch, key, or seat the refill expects on one side and the shape the spool expects on the other. Or it changes the coil width, filling the gap when a refill is narrower than the spool. The adapter only changes how the coil is held.

Do you need an adapter, or just the matching spool?

Start here, because the cheapest answer is usually no adapter at all.

Your situation What you need
You buy a refill made for the reusable spool you own Nothing. Load the refill on the matching spool.
You buy your first refill and own no reusable spool The matching reusable spool, not an adapter.
You own a reusable spool from one system and a refill from another An adapter, if one exists for that pair. Check the fit first.

The stocked example makes the point. The Anycubic Reusable Filament Spool for 1kg Refills (ID 23527) at $13.99 takes 1kg Anycubic refill coils in 1.75mm, in PLA, PLA+, and PETG. One spool serves every refill of that size, and the refill chips move onto the spool flanges so an ACE Pro printer still reads the material, color, and remaining volume.

What are the four adapter types?

1. The brand-matched reusable spool

Two spool halves, made for one refill system, twist or snap together around the coil. The Anycubic spool in this guide is this type: two halves, a threaded connection, a twist lock with a click, and a 196 x 67mm size stated on the listing. It is ABS, rated high-temperature resistant up to 80C per the listing. Buy this type first when it exists for your refill. It is the only type where fit is guaranteed by the maker.

2. The adapter plate

An adapter plate is a flat printed ring that sits between one spool half and the refill. It exists because some reusable spools have a notched interface that a refill from another system does not match. Filamentive publishes this design for its refills used with a Bambu Lab reusable spool. The plate only translates the notch. It adds no width and no hub, so it only works when the refill core already fits the spool hub and the coil width already matches the spool.

3. The printed MasterSpool

A MasterSpool is a reusable spool you print yourself, in two halves, and load refill coils onto. Filamentive publishes a printed masterspool for its refills, printed twice, one half per print. A printed Prusament to MasterSpool adapter works the same way in reverse, converting an empty Prusament spool into one that accepts refills with a press fit. The model author recommends PETG, notes PLA might work but is untested, and warns to test print a 1cm tall section of the fit ridge first, because the fit depends on your printer calibration.

A printed spool is only good up to the softening temperature of the filament it was printed from, per forum reports cited in the refill vs spool guide on this site. Print adapter parts in PETG or a higher temperature material when the spool will see dryer heat.

4. The cardboard-spool collar adapter

Some filament ships on cardboard spools. When the filament runs out, the cardboard core is still a usable spool body, and a collar adapter turns it into a reusable spool for refills. The adapter is two collars that connect to each other inside the cardboard core with a tab system, plus a hole that holds the filament end by friction. Published models list separate collar sizes for different cardboard spool brands, because core sizes differ by several millimetres between brands. Measure your spool core before you print.

How do you check the fit before you buy or print an adapter?

Four checks, in order. If any one fails, stop. Do not compress the coil to make it fit, and do not remove filament turns to shrink it. Both moves destabilize the coil, per the KJI 3D loading guide.

  1. Coil inner diameter against the hub. The refill core must slide onto the hub or the adapter with a snug fit and no wobble.
  2. Coil width against the spool width. The coil must sit inside the flanges with no section riding above the sidewall. A coil that is too wide keeps the spool halves from closing.
  3. Notch and key alignment. If the spool or the refill has a notch, a cutout, or a key, find it before you place the coil. On the Bambu Lab system the refill has a small cutout next to the identification tag, and the spool has a plastic notch that lines up with it. Forcing a coil against its key pinches the inner turns.
  4. Chip and label placement. Some refills carry identification chips that must move onto the spool flanges. On the Anycubic system, remove both stickers and both chips from the refill, if present, and install the new chip stickers onto both spool flanges before you load the coil.

Before you load filament into the extruder, mount the finished spool on the holder and confirm it rotates freely, with no scraping against the holder, the printer frame, a wall, or a dryer.

How do you load a refill on the stocked reusable spool?

These steps follow the Anycubic loading sequence stated on the live listing for the Anycubic Reusable Filament Spool for 1kg Refills (ID 23527), plus the control principles from the KJI 3D loading guide. The order is the whole method: lock first, straps last.

  1. Label the filament. Remove both stickers and both chips from the refill, if present, and install the new chip stickers onto both spool flanges. The chips travel with the refill, not with the spool.
  2. Open the spool. Separate the two halves and lay the half with the hub facing up on a clean, flat surface. Check both halves for cracked tabs.
  3. Load the coil with its straps still on. Set the refill coil onto the open half, align the filament with the latch, and snap the coil into place. Check the unwind direction so the filament leaves toward the inlet without a sharp bend.
  4. Lock the spool. Close the spool, press firmly, and rotate until you hear a click.
  5. Remove the straps last. Only once the spool is locked, remove the bonding strap and thread the filament into the spool hole. Remove the straps one at a time, keeping one hand on the outer turns. Never remove all restraints at once and then search for the filament end. Put the filament end straight into the retaining hole or clip.
  6. Mount and watch the first minutes. Place the spool on its holder, confirm it turns freely, and feed the filament through any guide tube, sensor, or dry box inlet before it reaches the extruder. Watch the spool turn for the first few minutes. It should unwind smoothly, without the filament catching under a loop or rubbing hard on a spool edge.

For PETG refills, dry the filament first: Anycubic states drying at 55 to 65C for 6 to 8 hours before printing. The stocked spool is ABS and rated high-temperature resistant up to 80C per its listing, so check your dryer temperature against that rating first.

How do you load a refill with an adapter plate or a printed spool?

The pattern is the same for an adapter plate and a printed MasterSpool. Only the parts change.

Adapter plate, following the Filamentive sequence for its refills on a Bambu Lab reusable spool: one half notched side up, adapter on it and lined up with the notch, refill on the adapter with its straps still on, second half on top and spun to lock, then remove the straps. SparkLab states the same sequence: twist apart, align the notch with the cutout, spin until you hear a click, remove the tabs, apply the sticker.

Printed MasterSpool: print both halves in PETG or a higher temperature material, not PLA, if the spool will see dryer heat. For a press-fit adapter, test print a 1cm tall section of the fit ridge first. Place one half flat, set the refill on the core with its straps still on and lined up with the cutouts, place the second half over it and lock it per the model, then unwrap the straps through the cutouts one at a time. Park the filament end in a hole or clip in the flange, then mount the spool and check that it turns freely.

What mistakes tangle a refill?

Most refill tangles are not factory knots. They happen when the free filament end slips under another loop after handling. The KJI 3D guide states the rule plainly: never let go of the filament end unless it is secured in a spool hole, held in your hand, or fed into the printer.

  • Cutting the straps before the spool is locked. The coil loosens, loops cross, and the print jams halfway through.
  • Removing all restraints at once. Cut or release one tie at a time, with a hand on the outer turns.
  • Pulling several feet of filament off the spool to find the end. Release only what the printer route needs.
  • Tucking the loose end between the flanges instead of in the retaining hole. A loose end migrates during storage and creates a crossover that is hard to spot until the print fails.
  • Loading the coil upside down or against its key. If the coil will not sit flush, stop and inspect.
  • Mixing systems without checking the fit first.

Troubleshooting: what went wrong and how do you fix it?

Symptom Likely cause Fix
Spool halves will not close Wrong spool model, coil too wide, or a packaging insert still around the inner diameter Verify the spool model, remove the insert, and check coil width. Do not remove filament turns.
Spool turns with a scraping sound Off-center coil, warped flange, or contact with the holder Re-center the coil, inspect the flange, and check holder clearance.
Filament catches early in the print A strand crossed under another strand, or a loop caught on the spool rim Pause if safe, free the crossover while keeping tension on the filament, then secure the routing.
Filament pops and prints rough Damp filament, usually PETG Dry the filament before printing. Anycubic lists 55 to 65C for 6 to 8 hours for its PETG refill.
Printer does not identify the material Chips not moved to the flanges Move both chips and both stickers from the refill onto the spool flanges before loading.

Which refill should you buy first?

The full comparison lives in PLA vs PLA+ vs PETG: Pick the Right 3D Printer Filament for Drone Parts and in PLA PLA+ PETG Filament: Which to Print RC Parts With. All three stocked refills are 1.75mm, 1KG coils, refill only, with no spool included. All three need a reusable spool, a previous spool, or a printed spool.

Refill Price What the listing states
Anycubic PLA Filament Refill, 1.75mm, 1KG (ID 17667) $19.99 ACE Pro chip. Strong bed adhesion at just 45C.
Anycubic PLA+ Filament Refill, 1.75mm, 1KG (ID 17695) $24.99 Twice the toughness of standard PLA. Plus or minus 0.02mm tolerance.
Anycubic PETG Filament Refill, 1.75mm, 1KG (ID 17689) $18.99 Twice the impact resistance of standard PLA. Plus or minus 0.02mm tolerance. Vacuum packed.

Buy PLA+ first for drone parts that take hits. Buy PETG first for parts that flex, get wet, or live outdoors. Buy PLA first only if you prototype a lot. For ASA and nylon, read PETG vs ASA vs Nylon: Best Filament for RC Parts. For per-part FPV picks, read Best Filament FPV Drone Builders Use for Frames and Mounts.

Parts used in this guide

All products below were verified live and in stock on 2026-11-21, at the live store prices shown. Re-verify at publish time. In-stock parts ship from our secure facility in Queensbury, NY, within the USA only.

  • Anycubic Reusable Filament Spool for 1kg Refills (ID 23527), $13.99. Two halves, threaded connection, twist lock with a click. Fits 1kg refill coils in 1.75mm, PLA, PLA+, and PETG. Spool size 196 x 67mm, ABS, up to 80C per the listing. No filament included.
  • Anycubic PLA Filament Refill, 1.75mm, 1KG (ID 17667), $19.99. Refill coil only, no spool included. ACE Pro chip, strong bed adhesion at 45C.
  • Anycubic PLA+ Filament Refill, 1.75mm, 1KG (ID 17695), $24.99. Refill coil only, no spool included. Twice the toughness of standard PLA, plus or minus 0.02mm tolerance.
  • Anycubic PETG Filament Refill, 1.75mm, 1KG (ID 17689), $18.99. Refill coil only, no spool included. Twice the impact resistance of standard PLA, plus or minus 0.02mm tolerance, vacuum packed.

No standalone spool adapter product is stocked. The stocked answer is the reusable spool itself (ID 23527), which fits the three refills above with no adapter needed. The adapter section of this guide is method only, not products sold here.

Related guides

Frequently asked questions

What does a filament refill spool adapter do?

It bridges a spool-less refill coil and a spool it was not made for. It changes the hub size, the locking interface, or the coil width so the coil sits centered, stays contained by the flanges, and turns smoothly on the printer.

Do I need an adapter if I buy the matching reusable spool?

No. A refill made for your spool fits out of the box, and the Anycubic reusable spool in this guide takes the three stocked 1kg refills with no adapter needed. You need an adapter only when the refill and the spool come from different systems.

Will any refill fit any reusable spool?

No. A refill that looks close in diameter may still sit too loosely, rub the spool edges, or fail to lock onto the hub. Check the four fit checks in this guide first: coil inner diameter against the hub, coil width against the spool width, notch and key alignment, and chip placement.

Can I print my own spool adapter?

Yes, and the MasterSpool project is the standard way to do it. Print both halves, load the refill with its straps still on, lock the halves, then remove the straps through the cutouts. Use PETG or a higher temperature material, not PLA, if the spool will see dryer heat.

Why does my refill tangle after loading?

Most refill tangles are not factory knots. They happen when the free filament end slips under another loop after handling, or when the straps come off before the spool is locked. Lock the spool first, remove the straps one at a time, and park the filament end in the retaining hole the moment the last strap is off.

Can I use a refill spool in a filament dryer?

It depends on the spool material. The stocked Anycubic reusable spool is ABS and rated high-temperature resistant up to 80C per its listing, so it can go in most dryers. A printed spool is only good up to the softening temperature of the filament it was printed from.

Do I need to move the chip when I load a refill?

If your refill carries identification chips, yes. On the Anycubic system, remove both stickers and both chips from the refill, if present, and install the new chip stickers onto both spool flanges before you load the coil. The printer reads the material, color, and remaining volume from the chips on the flanges.

Sources

PETG vs ASA vs Nylon: Best Filament for RC Parts

PETG is the default pick for most RC and drone parts. ASA is the pick when the part lives outdoors in sun and weather. Nylon is the toughest of the three, and the hardest to print, so it belongs on high-load brackets, gears, and wear parts once you can keep it dry and enclosed. First functional part on an open-frame printer? Start with PETG. Part sits in sun all summer? Print it in ASA. Repeated load and failure is not an option? Nylon earns its extra work.

How to read the numbers in this guide

Datasheet figures vary by brand, grade, test method, and moisture state, so this guide does not mix brands into one table. The comparison table below is qualitative on purpose. Where a figure is given, it comes from one named manufacturer datasheet and describes a lab specimen printed at 100 percent infill, not your part. For PLA and PLA+ basics, read the PLA guide first: PLA vs PLA+ vs PETG: Pick the Right 3D Printer Filament for Drone Parts.

Is PETG good for RC and drone parts?

Yes. PETG is the easy engineering filament and the baseline for rigid drone and RC parts. It prints on most printers without an enclosure, flexes instead of snapping, and holds up better than PLA under knocks, heat, and water. The listing for the stocked PETG refill states impact resistance twice that of standard PLA, with enhanced chemical and water resistance. That figure comes from the live listing.

Heat: PETG handles more heat than PLA but less than ASA or nylon. Polymaker lists 69C and Bambu Lab lists 71C for its PETG Basic, both heat deflection at 0.45 MPa.

Strength: PETG is strong and a little flexible. It bends under load instead of cracking through, and its layers hold together better than any other common filament. CadFlow, using Polymaker datasheets, lists PETG at 48 MPa printed flat and 45.7 MPa printed upright, so it keeps about 95 percent of its strength across the layers.

Warping and enclosure: PETG warps little and needs no enclosure. Fumes: none special.

Settings: typical ranges across the Filwiz, Techietory, and ADP guides are nozzle 230 to 250C, bed 70 to 80C, fan 30 to 60 percent. Too much cooling weakens layer adhesion.

Weaknesses: PETG strings more than PLA, so tune retraction until the strings stop. It bonds hard to a bare bed, so use a release agent such as a glue stick on smooth PEI. Damp PETG prints rough and weak, so dry it at about 65C for 4 to 6 hours if you hear popping.

Is ASA good for RC and drone parts?

Yes, when the part lives outdoors. ASA is essentially ABS with UV resistance built in. It was developed to fix the weakness that kills ABS outside: yellowing and brittleness after sun exposure. If your part goes outdoors, ASA is the default choice, and every top guide agrees on that point.

Heat: ASA handles more heat than PETG by a clear margin. Polymaker lists 103C and Bambu Lab lists 100C for its ASA, both heat deflection at 0.45 MPa.

Strength: ASA is tough on impact and rigid enough for structural parts, but it is not stronger than PETG in a straight pull. Polymaker lists ASA at 43.8 MPa printed flat and 32 MPa printed upright, against PETG at 48 and 45.7 MPa. Pick ASA for sun and heat, not for raw tensile strength.

UV and weather: this is the reason ASA exists. It holds its color and structure under UV, where ABS yellows and turns brittle and PLA breaks down in direct sunlight over time. Use ASA for antenna mounts, drone housings, and RC car bodies.

Warping and enclosure: ASA warps significantly without an enclosure, and it is the number one ASA printing problem across the guides. It shrinks as it cools, so drafts cause warping and layer splitting. An enclosure is strongly recommended, with a warm chamber around 35 to 50C. A brim of 5 to 10 mm helps on large parts.

Fumes: ASA emits styrene fumes while printing, so ventilation is required, not optional. Print in a well-ventilated area or exhaust the fumes outside. A carbon filter is the minimum for ASA, per the Filwiz guide.

Settings: typical ranges across the Filwiz, Techietory, and ADP guides are nozzle 240 to 260C, bed 90 to 110C, fan 0 to 30 percent, print speed 40 to 80 mm per second.

Weaknesses: without an enclosure ASA warps and splits, and with too much fan it cracks between layers. It costs about a third more per spool than PETG, per the CadFlow price check.

Is nylon good for RC and drone parts?

Yes, for the hardest jobs, and only if you respect its moisture problem. Nylon, also called polyamide or PA, offers the best combination of tensile strength, impact resistance, and abrasion resistance of any common FDM filament. It bends instead of shattering, resists wear, and is slippery enough for gears, bushings, and living hinges. It is also the hardest of these three materials to print.

Heat: nylon handles more heat than PETG and about the same as ASA, with the exact figure depending on grade and annealing. Polymaker lists its nylon copolymer at 111C heat deflection after annealing, the highest of the six filaments CadFlow compared.

Strength: nylon is the strongest of the three in a straight pull and the toughest on impact. CadFlow lists 78 MPa printed flat and 45.8 MPa printed upright, only 59 percent of its flat strength across the layers. Orientation matters most for nylon: print a nylon hook lying down, not standing up.

Wear: nylon is the pick for parts that slide, rub, or hinge. Gears, hinges, bushings, snap-fit clips, wear plates, and living hinges are nylon jobs. A nylon part does not shatter. It bends, absorbs the hit, and returns to shape

Warping and enclosure: nylon warps severely without an enclosure. An enclosure is required, with a warm chamber around 45 to 65C, and a large brim plus a Garolite bed surface helps adhesion.

Moisture: this is the nylon problem that decides everything else. Nylon absorbs moisture from the air fast, and wet nylon prints with popping, stringing, rough surfaces, and weak layer bonds. Filwiz cites up to 9.5 percent moisture by weight for PA6 and Prusa lists up to 10 percent, while CadFlow cites 2.82 percent for Polymaker PolyMide CoPA. Dry it at 70 to 80C for 6 to 12 hours before printing, and print from a dry box if possible.

Settings: typical ranges across the Filwiz, Techietory, and ADP guides are nozzle 240 to 290C depending on grade, bed 70 to 90C, fan 0 to 30 percent, print speed 30 to 60 mm per second. Filled nylon needs a hardened steel nozzle.

Weaknesses: wet filament, no enclosure, and wrong orientation are the three killers. Upright orientation throws away nearly half its strength.

How do PETG, ASA, and nylon compare side by side?

Property PETG ASA Nylon (PA6 / PA12)
Easiest to print Easiest of the three Moderate, needs enclosure Hardest of the three
Heat resistance Moderate, better than PLA High, best for sun and hot cars High, best after annealing
Strength in a straight pull Strong Strong, slightly below PETG Strongest of the three
Strength across the layers Best, about 95 percent of flat strength Weaker, about 73 percent of flat strength Weakest, about 59 percent of flat strength
Impact resistance Good, flexes instead of snapping Good, tougher than PLA on a notched test Excellent, bends and returns to shape
Stiffness Stiff with a little give Rigid Stiff, more flexible in thin layers
UV and weather resistance Moderate Excellent Poor
Warping Low to moderate Moderate to high High
Moisture sensitivity Moderate Low Very high
Chemical resistance Good Good Excellent
Wear resistance Fair Fair Excellent, best for gears and hinges
Enclosure needed No, optional Recommended, near required Required
Ventilation needed No Yes, styrene fumes Good practice
Typical price per kilogram Lowest of the three Middle Highest of the three

Nylon wins flat by a wide margin and loses the most upright. PETG barely loses strength across the layers, so a PETG hook printed upright still holds while a nylon hook printed upright can snap. Turn the part so the main load runs along the layers. Heat figures agree on the order and disagree on the digits across brands, so use the order, not the digits.

Which filament wins for each drone and RC part?

Small frames, whoop frames, and prop guards. PETG first. It is the safest first plastic for a small frame, per the DroneTrader guide, and the default for whoop frames and prop guards, per the Prusa Knowledge Base summary in that guide. For larger builds, DroneTrader recommends a molded carbon kit for frame arms.

Mounts, brackets, and standoffs. PETG for rigid mounts indoors or in shade, ASA for mounts in sun. For a high-load bracket, nylon is the pick, but only after your own validation, per the ADP guide.

Outdoor parts, canopies, and housings. ASA, without a close second. Anything that lives outside, sits on a car dashboard, or flies in direct sun all summer belongs in ASA: antenna mounts, camera housings, field boxes, RC car bodies, and garden and automotive exterior parts. PETG ages faster in sun, PLA breaks down in sun, and nylon has poor UV resistance.

High-heat parts, motor mounts, and enclosures. ASA first, nylon second, and the stocked HT-PLA Pro as the easy option. Parts near motors and hot electronics need heat resistance PETG does not have. HT-PLA Pro prints like PLA with no enclosure and anneals at 100C for 30 minutes for its best heat resistance.

Gears, hinges, bushings, and wear parts. Nylon, and nothing else in this comparison. Its abrasion resistance and slipperiness are why gears, hinges, and living hinges are nylon jobs in every guide.

RC car and truck parts. PETG for brackets, chassis pieces, and guards that take hits. ASA for bodies and exterior parts in sun. Nylon for gears and suspension parts that wear.

What not to print. Print the parts that hold things. Buy the parts that spin or carry current. No filament here replaces a motor, a speed controller, a flight controller, a battery, or a propeller. Printed propellers are not a safe substitute for molded props. Bench-test every printed structural part with the propellers off, and check it for cracks after every hard landing.

What mistakes should you avoid?

  • Jumping straight to nylon. Do not skip PETG and jump straight to nylon. The skills you build dialing in PETG transfer directly to the harder materials.
  • Printing ASA without an enclosure or ventilation. ASA without an enclosure warps and splits, and without ventilation it fills the room with styrene fumes. Get the enclosure and the airflow first.
  • Printing nylon wet. Wet nylon is the most common nylon failure. If you hear popping or see rough surfaces and weak layer bonds, the filament is wet. Dry it and print from a dry box. A strong material printed wet can end up weaker than dry PETG, per the 3DX guide.
  • Buying on the flat tensile number alone. It is the most flattering value on the datasheet. For printed parts, the across-layer strength and the heat deflection figure usually decide whether a part survives, per the 3DX guide.
  • Comparing brands’ datasheets directly. Test settings differ, so compare materials within one brand’s sheets, per the 3DX guide.
  • Ignoring orientation. A part printed standing up, with the load pulling its layers apart, can snap where the same part printed lying down would hold. Think about the crash direction before you slice.
  • Assuming carbon fiber means tougher. Fibers add stiffness, not toughness, and they wear brass nozzles, per the 3DX guide.
  • Skipping the test fit. Print a fit check in PLA or PLA+ before committing to a long ASA or nylon print. A fit check that fails costs minutes instead of hours.

Why is my print failing?

Problem Likely cause Fix
Warping, corners lifting Cold bed, drafts, no enclosure Raise the bed temperature, add a 5 to 10 mm brim, close the enclosure.
Layer splitting or cracking Too much cooling, low nozzle temperature, cold chamber Reduce the fan to near zero for ASA and nylon, raise the nozzle temperature 5 to 10C, keep the enclosure warm.
Stringing Wet filament, high temperature Dry the spool, lower the temperature, tune retraction.
Popping, bubbles, rough surfaces Moisture in the filament Dry the spool fully. For nylon, dry 70 to 80C for 6 to 12 hours and print from a dry box.
Poor bed adhesion Dirty bed, wrong bed temperature, wrong surface Clean the bed with isopropyl alcohol, re-level, use glue stick on smooth PEI. Nylon usually needs Garolite or PVA glue.
Part snaps along a layer line Load across the layers, weak layer bonding Reorient the part so the load runs along the layers, reduce the fan, add walls.
ASA part smells and the room feels stuffy Styrene fumes, no ventilation Stop the print, ventilate the room, and do not print ASA again without a carbon filter.
Nylon part warps on a large flat print No enclosure, damp filament, wrong bed surface Enclose the printer, dry the filament, use a large brim and a Garolite bed surface.

Which filament should you buy?

First functional part, open-frame printer, most RC and drone parts. Buy PETG. It prints without an enclosure, flexes instead of snapping, and covers guards, brackets, chassis pieces, and mounts. The stocked PETG refill is the Anycubic PETG Filament Refill, 1.75mm, 1KG (ID 17689) at $18.99. It is a refill coil only with no spool included, so you need a reusable spool.

Part that lives outdoors, sits in sun, or sits in a hot car. Buy ASA. No ASA filament is stocked at the time of writing, so there is no ASA product link in this guide. Buy ASA from a filament maker whose datasheet you have read, and print it enclosed and ventilated.

High-load bracket, gear, hinge, or wear part, and you own an enclosure and a dryer. Buy nylon. No nylon filament is stocked at the time of writing, so there is no nylon product link in this guide. Buy the grade that matches the job, PA6 for strength, PA12 for lower moisture absorption, and dry it before every print.

Hot spot near a motor or electronics, and you want the easy option. Buy HT-PLA Pro. The stocked Polymaker HT-PLA Pro Filament, 1.75mm, 1KG (ID 17644) is $29.99. It prints like PLA with no enclosed chamber and anneals at 100C for 30 minutes for its best heat resistance.

FAQ

Which filament is strongest, PETG, ASA, or nylon? Nylon is the strongest common FDM filament overall, especially in carbon fiber filled form. On an open-frame printer, PETG is the strongest practical pick, because it needs no enclosure. Source: Techietory FAQ section, 3DX FAQ section.

Is ASA better than PETG for outdoor parts? Yes. ASA resists UV light and weathering far better than PETG, so it keeps its color and structure outdoors while PETG ages faster in sun. PETG is easier to print and stronger across the layers, so use PETG indoors and ASA outside. Source: Techietory FAQ section, Filwiz material comparison.

Do I need an enclosure to print ASA or nylon? Yes, for reliable results. An enclosure holds a stable chamber temperature of roughly 40 to 60C, which reduces warping and layer splitting. ASA warps significantly without one, and nylon warps severely without one. PETG prints fine without one. Source: Techietory FAQ section, Filwiz enclosure guide.

Can I print nylon without drying it first? No. Nylon absorbs moisture from the air within hours, and wet nylon prints with bubbles, rough surfaces, and weak layer bonds. Dry it at 70 to 80C for 8 to 12 hours before printing, store it sealed with desiccant, and print from a dry box when possible. Source: Techietory nylon section, Filwiz nylon section.

Which filament should I use for a drone frame? PETG for a small frame, such as a whoop. ASA for a frame or canopy that lives outdoors in sun. Nylon or carbon fiber nylon only for high-load prototypes, and only after your own validation. For frame arms on a large build, a molded carbon kit is the safer buy. Source: ADP quick reference, DroneTrader component matrix.

Is PETG stronger than PLA? PETG is tougher, more heat resistant, and more chemically resistant than PLA, and it flexes instead of shattering. PLA is stiffer and better for visual models. In Bambu Lab datasheet figures, PETG Basic beats PLA Basic on tensile strength, impact strength, and heat resistance, but other brands publish different numbers. Source: Techietory FAQ section, 3DX FAQ section.

Can you print an entire drone? No. You can print the frame, mounts, prop guards, and battery holders, but motors, flight controllers, speed controllers, batteries, and propellers must be bought. Printed parts hold things; they do not spin or carry current. Source: DroneTrader FAQ section.

Parts used in this guide

Prices and stock were verified live on qualityrcparts.com on 2026-11-21. Both items below are in stock and purchasable. No ASA filament and no nylon filament is stocked at the time of writing: a store search for “asa” returns 0 products, a store search for “nylon filament” returns 0 products, and a store search for “filament” returns 9 products, none of them ASA or nylon filament. The nylon search results are hardware, such as nylon screws, standoffs, propellers, and hinges, not filament. No ASA or nylon product is linked because none exists.

  • Anycubic PETG Filament Refill, 1.75mm, 1KG (ID 17689) – $18.99. Refill coil only, no spool included. Impact resistance twice that of standard PLA per the listing, 1.75mm diameter, 1KG. The PETG pick in this guide.
  • Polymaker HT-PLA Pro Filament, 1.75mm, 1KG (ID 17644) – $29.99. Full 1KG spool. Prints like PLA with no enclosed chamber and no hardened nozzle needed, anneals at 100C for 30 minutes for its best heat resistance. The stocked heat-resistant option for hot spots in this guide.

Shipped fast and securely from our secure facility in Queensbury, NY. QRC ships within the USA only.

Related guides

Sources

Last updated: 2026-11-21